Ag Test
Criteria for identifying sockets include which of the following?
All of the above
Torque means slippage.
False
A center punch is usually how long?
Four to six inches
Most chisels are made of _____
High carbon steel
Which of the following is an advantage of a six-point socket?
It is stronger.
By what size increments does an open end wrench increase?
1/16 inch
How are countersinks sized?
According to weight
Which of the following is an adjustable wrench designed to fit hexagonal nuts?
Adjustable wrench
Which of the following is used to shift parts so corresponding holes align?
Aligning punch
Types of tap include ______
All of the above
A diamond point chisel is used for cutting ____
Big grooves
Safety precautions which should be taken when using a hammer include which of the following?
Both B and C
Which is the following completely surrounds the nut or bolt head?
Box-end wrench
Which of the following is often referred to as a flex-head handles or speeders?
Breaker bars
In which of the following ways is an impact driver set useful?
Breaking loose rusty fasteners
Gasket and carbon scrapers are used ti scrape off which of the following from machine parts?
Carbon
Which of the following is a tool used to make the location of a home which is going to be drilled?
Center punch
A combination square _____
Determines if something is square or at a 90 or 45 degree angle
A feeler gauge _______
Determines the clearance between parts
A screw pitch ______
Determines the clearance between parts
What is the trade name for a tapered screw extractor?
Ezzy-Out
A combination wrench has a different size openings on both ends.
False
A trade name for a three-jaw, plain bearing, key type drill chuck is 'Ezzy-Out.'
False
Ball peens are heavier then blacksmith hand hammers.
False
Hacksaws should be stored in a toolbox.
False
If the handles of plies are plastic-coated, electric shock is prevented.
False
It is permissible to use a hammer on a scratch awl.
False
Phillips, reed, and prince screwdrivers are interchangeable.
False
Screwdrivers are the most common and least misused hand tools.
False
The most common size for slip joint pliers is six inches.
False
Three thread types are standard, national fine and national coarse.
False
Twist drills are usually sharper than twist bits.
False
Which of the following is another term for a breaker bar?
Flex-head handle
How much do ball peens weigh?
Four to 12 ounces
Where is a neoprene insert located?
In a spark plug socket
How are screwdrivers sized?
Length of blade
The edges of a flat chisel are sharpened to a ______
None of the above
In what size range do putty knife blades come?
One-forth inch to six inches
Which of the following is an advantage of a ratchet?
Speed
Which of the following is a reamer mentioned in the production?
Spiral fluted reamer
Which of the following is NOT a type of torque wrench?
Square drive
Which of the following is used when there is NOT enough room for a regular screwdriver?
Standard offset screwdriver
A pin punch is used after which of the following?
Starter punch
Which of the following measurement tools is not considered a precision instrument?
Steel tape
Which tool is used to turn taps?
Tap wrench
What is an easy way to determine the size of a straight fluted screw extractor?
The size is stamped on the turn neck
A hacksaw blade should be installed with the teeth pointed away from the handle.
True
A pipe wrench should not be used to nuts and bolts.
True
If a twist drill is not tightened properly in the chuck it may slip and damage the drill shank.
True
It is possible to determine the size of a nut driver by the color of the handle.
True
Needle nose pliers are mostly used for electrical work.
True
Nut drivers are sized according to the socket size on the end.
True
One type of torque is the one-half inch click-type ratcheting wrench.
True
Twist drills diameters are sized by fractions of an inch.
True
When using chisels, you should always ______
Wear eye protection