MOD 8 SLAAC DHCPv6

Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server?

Add the ipv6 dhcp relay command to interface Fa0/0.

7. Which destination IP address is used when an IPv6 host sends a DHCPv6 SOLICIT message to locate a DHCPv6 server?

FF02::1:2

8. In which alternative to DHCPv6 does a router dynamically provide IPv6 configuration information to hosts?

SLAAC

5. Which command should be configured on a router interface to set the router as a stateful DHCPv6 client?

ipv6 address dhcp

Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0?

The state is not maintained by the DHCPv6 server under stateless DHCPv6 operation.

10. What process is used in ICMPv6 for a host to verify that an IPv6 address is unique before configuring it on an interface?

DAD

9. A company implements the stateless DHCPv6 method for configuring IPv6 addresses on employee workstations. After a workstation receives messages from multiple DHCPv6 servers to indicate their availability for DHCPv6 service, which message does it send to a server for configuration information?

DHCPv6 INFORMATION-REQUEST

13. A network administrator is entering the command ipv6 unicast-routing to start configuring DHCPv6 operation on a router. Which statement describes the function of this command?

It is required for sending ICMPv6 RA messages.

4. A client is using SLAAC to obtain an IPv6 address for its interface. After an address has been generated and applied to the interface, what must the client do before it can begin to use this IPv6 address?

It must send an ICMPv6 Neighbor Solicitation message to ensure that the address is not already in use on the network.

1. How does an IPv6 client ensure that it has a unique address after it configures its IPv6 address using the SLAAC allocation method?

It sends an ICMPv6 Neighbor Solicitation message with the IPv6 address as the target IPv6 address.

A network administrator configures a router to send RA messages with M flag as 0 and O flag as 1. Which statement describes the effect of this configuration when a PC tries to configure its IPv6 address?

It should use the information that is contained in the RA message and contact a DHCPv6 server for additional information.

A company uses the method SLAAC to configure IPv6 addresses for the workstations of the employees. A network administrator configured the IPv6 address on the LAN interface of the router. The interface status is UP. However, the workstations on the LAN segment did not obtain the correct prefix and prefix length. What else should be configured on the router that is attached to the LAN segment for the workstations to obtain the information?​

R1(config)# ipv6 unicast-routing

12. After booting, a client receives an ICMPv6 RA message with the M flag set to 0 and the O flag set to 1. What does this indicate?

The client should automatically configure an IPv6 address and then contact a DHCPv6 server for more information.

11. What are two characteristics of the SLAAC method for IPv6 address configuration? (Choose two.)

The default gateway of an IPv6 client on a LAN will be the link-local address of the router interface attached to the LAN. IPv6 addressing is dynamically assigned to clients through the use of ICMPv6.

After a host has generated an IPv6 address by using the DHCPv6 or SLAAC process, how does the host verify that the address is unique and therefore usable?

The host sends an ICMPv6 neighbor solicitation message to the DHCP or SLAAC-learned address and if no neighbor advertisement is returned, the address is considered unique

Refer to the exhibit. PC-A is unable to receive an IPv6 address from the stateful DHCPv6 server. What is the problem?

The ipv6 dhcp relay command should be applied to interface Gig0/0.

Refer to the exhibit. A network administrator is implementing the stateless DHCPv6 operation for the company. Clients are configuring IPv6 addresses as expected. However, the clients are not getting the DNS server address and the domain name information configured in the DHCP pool. What could be the cause of the problem?

The router is configured for SLAAC operation.

Refer to the exhibit. A network administrator is configuring a router for DHCPv6 operation. Which conclusion can be drawn based on the commands?

The router is configured for stateless DHCPv6 operation.

3. What two methods can be used to generate an interface ID by an IPv6 host that is using SLAAC? (Choose two.)

random generation EUI-64

2. Which method would an IPv6-enabled host using SLAAC employ to learn the address of the default gateway?

router advertisements that are received from the link router

Refer to the exhibit. Based on the output that is shown, what kind of IPv6 addressing is being configured?

stateless DHCPv6

6. What message informs IPv6 enabled interfaces to use stateful DHCPv6 for obtaining an IPv6 address?

the ICMPv6 Router Advertisement

A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?​

the link-local address of the router interface that is attached to the network