CCNA Introduction to Networks Chapter 2

Which interface allows remote management of a Layer 2 switch? A. the AUX interface B. the switch virtual interface C. the console port interface D. the first Ethernet port interface

B. the switch virtual interface

What is a result of using the service password-encryption command on a Cisco network device? A. All passwords in the configuration are not shown in clear text when viewing the configuration. B. The command encrypts the enable mode password. C. The command encrypts the banner message. D. A network administrator who later logs into the device will be required to enter an administrator password in order to gain access to the Cisco device.

A. All passwords in the configuration are not shown in clear text when viewing the configuration.

What criterion must be followed in the design of an IPv4 addressing scheme for end devices? A. Each IP address must be unique within the local network. B. Each IP address must match the address that is assigned to the host by DNS. C. Each IP address needs to be compatible with the MAC address. D. Each local host should be assigned an IP address with a unique network component.

A. Each IP address must be unique within the local network.

What benefit does DHCP provide to a network? A. Hosts can connect to the network and get an IP address without manual configuration. B. Duplicate addresses cannot occur on a network that issues dynamic addresses using DHCP and has static assignments. C. Hosts always have the same IP address and are therefore always reachable. D. DHCP allows users to refer to locations by a name rather than an IP address.

A. Hosts can connect to the network and get an IP address without manual configuration.

Which two features are characteristics of flash memory? (Choose two.) A. The contents of flash may be overwritten. B. Flash receives a copy of the IOS from RAM when a device is powered on. C. Flash provides nonvolatile storage. D. The contents of flash may be lost during a power cycle. E. Flash is a component in Cisco switches but not in Cisco routers.

A. The contents of flash may be overwritten. C. Flash provides nonvolatile storage.

Which two characters are allowed as part of the hostname of a Cisco device? (Choose two.) A. dash B. space C. tab D. numbers E. question mark

A. dash D. numbers

What is a user trying to determine when issuing a ping 10.1.1.1 command on a PC? A. if there is connectivity with the destination device B. the path that traffic will take to reach the destination C. what type of device is at the destination D. if the TCP/IP stack is functioning on the PC without putting traffic on the wire

A. if there is connectivity with the destination device

What command can be used on a Windows PC to see the IP configuration of that computer? A. ipconfig B. show interfaces C. show ip interface brief D. ping

A. ipconfig

Why is it important to configure a hostname on a device? A. to identify the device during remote access (SSH or telnet) B. a hostname must be configured before any other parameters C. a Cisco router or switch only begins to operate when its hostname is set D. to allow local access to the device through the console port

A. to identify the device during remote access (SSH or telnet)

Which statement is true about the running configuration file in a Cisco IOS device? A. It is automatically saved when the router reboots. B. It affects the operation of the device immediately when modified. C. It should be deleted using the erase running-config command. D. It is stored in NVRAM.

B. It affects the operation of the device immediately when modified.

A network administrator needs to keep the user ID, password, and session contents private when establishing remote CLI connectivity with a switch to manage it. Which access method should be chosen? A. AUX B. SSH C. Console D. Telnet

B. SSH

Which procedure is used to access a Cisco 2960 switch when performing an initial configuration in a secure environment? A. Use Telnet to remotely access the switch through the network. B. Use the console port to locally access the switch from a serial or USB interface of the PC. C. Use Secure Shell to remotely access the switch through the network​. D. Use the AUX port to locally access the switch from a serial or USB interface of the PC.

B. Use the console port to locally access the switch from a serial or USB interface of the PC.

Passwords can be used to restrict access to all or parts of the Cisco IOS. Select the modes and interfaces that can be protected with passwords. (Choose three.) A. boot IOS mode B. VTY interface C. privileged EXEC mode D. Ethernet interface E. console interface F. router configuration mode

B. VTY interface C. privileged EXEC mode E. console interface

A network administrator is planning an IOS upgrade on several of the head office routers and switches. Which three questions must be answered before continuing with the IOS selection and upgrade? (Choose three.) A. Are the devices on the same LAN? B. What models of routers and switches require upgrades? C. What features are required for the devices? D. Do the devices have enough NVRAM to store the IOS image? E. Do the routers and switches have enough RAM and flash memory for the proposed IOS versions? F. What ports are installed on the routers and switches?

B. What models of routers and switches require upgrades? C. What features are required for the devices? E. Do the routers and switches have enough RAM and flash memory for the proposed IOS versions?

A new network administrator has been asked to enter a banner message on a Cisco device. What is the fastest way a network administrator could test whether the banner is properly configured? A. Reboot the device. B. Power cycle the device. C. Exit privileged EXEC mode and press Enter. D. Enter CTRL-Z at the privileged mode prompt. E. Exit global configuration mode.

C. Exit privileged EXEC mode and press Enter.

While trying to solve a network issue, a technician made multiple changes to the current router configuration file. The changes did not solve the problem and were not saved. What action can the technician take to discard the changes and work with the file in NVRAM? A. Close and reopen the terminal emulation software. B. Delete the vlan.dat file and reboot the device. C. Issue the reload command without saving the running configuration. D. Issue the copy startup-config running-config command.

C. Issue the reload command without saving the running configuration.

Which two functions are provided to users by the context-sensitive help feature of the Cisco IOS CLI? (Choose two.) A. providing an error message when a wrong command is submitted B. selecting the best command to accomplish a task C. displaying a list of all available commands within the current mode D. determining which option, keyword, or argument is available for the entered command E. allowing the user to complete the remainder of an abbreviated command with the TAB key

C. displaying a list of all available commands within the current mode D. determining which option, keyword, or argument is available for the entered command

A router has a valid operating system and a configuration stored in NVRAM. When the router boots up, which mode will display? A. global configuration mode B. ROM monitor mode C. user EXEC mode D. setup mode

C. user EXEC mode

Why would a Layer 2 switch need an IP address? A. to enable the switch to receive frames from attached PCs B. to enable the switch to send broadcast frames to attached PCs C. to enable the switch to function as a default gateway D. to enable the switch to be managed remotely

D. to enable the switch to be managed remotely

Refer to the exhibit. A switch was configured as shown. A ping to the default gateway was issued, but the ping was not successful. Other switches in the same network can ping this gateway. What is a possible reason for this? A. The VLAN IP address and the default gateway IP address are not in the same network. B. The ip default-gateway command has to be issued in the VLAN interface configuration mode. C. The local DNS server is not functioning correctly. D. The default gateway address must be 192.168.10.1. E. The no shutdown command was not issued for VLAN 1.

E. The no shutdown command was not issued for VLAN 1.