CDC Set B Vol 1
Which 30 mm cannon is internally mounted in the A-10 aircraft?
GAU-8/A
Why is it important to monitor net explosive weight (NEW) during a bomb buildup operation?
If ignited, excessive NEW may cause propagation of an explosive from one location to another
After 463L pallets are positioned on a rollerized trailer, what can you use to secure the pallets to the trailer?
MB-1 chain assemblies and/or tie-down straps
Before using an electrical drill, what is the first thing you should do?
Make sure the diameter of the hole to be drilled is within the capacity of the drill.
What kind of movement supports on-base activities to or from the flightline?
Operational
The primary difference between a bobtail and a pickup truck is the
bobtail's back end is shortened by about one half
What chapter of TO 11-1-38 covers configuration of the MHU-141 munitions trailer?
one
which tool can initiate cycling ammunition through the universal ammunition loading system (UALS) replenisher manually?
1/2-inch speed wrench
Which TO covers the rapid-assembly and inspection procedures of nonnuclear munitions
11A-1-63
what is the maximum amount of pounds the MB-4 aircraft towing tractor can tow and push?
140,000
What is the maximum load capacity of the MHU-110/M trailer?
15,000 pounds
When specifically authorized for transporting nuclear weapons and materiel, how many CGU-1/B tie down straps need to be used as a substitute for every on MB-1 tie down assembly?
2
The sterring system on the MHU-141/M trailer has a turning radius of how many inches?
200
What munitions item is not loaded into transport modules by munitions personnel?
20mm
. with the forks level, what is the maximum reach of the variable-reach forklift?
22 feet
What is the lifting capacity of the MJ-1 series lift truck?
3,000 pounds
what is the weight capacity of the pneumatic hoist that are attached to the gantry's I-beam of the munitions assembly conveyor (both versions)?
4,000 lbs. (A/E32K-3, MAC); 6,000 lbs. (A/E32K-9, MAC II).
What is the maximum depth of water you may drive a rough-terrain forklift through?
5 feet
what is the minimum number of feet required to assemble the A/E32K-3, munitions assembly conveyor?
50 x 100
What is the lifting capacity of the MHU-83-series lift truck?
7,000 pounds
How many pounds per square inch (psi) of clean, dry air is required at the tool end of the air hose to ensure the tool is operating safely and efficiently?
90
Even though TO 11-1-38 has its own safety section, what other publication should you reference for safely transporting explosive items on base?
AFMAN 91-201
What transport module used for decoy munitions has a maximum capacity of 30 magazines?
ALE-50
When should you replace a nuclear certified MB-1 tie down/chain assembly item?
After finding any cracks, Bent/worn parts, or excessive corrosion
How often should the positive locking device on the doors of munitions transport modules be checked?
After loading, unloading, and periodically between stops
What condition would prevent an operator rom applying power to a hoist or other powered lifting device?
An AF Form 979 is attached to the unit.
Which approved restraining device can be used for securing munitions on USAF vehicles/trailers?
Chains/binders, cargo nets, and tie down straps
which subassembly on the universal ammunition loading system (UALS) replenisher assembly prevents accidentally loading a spent cartridge into the loader assembly
Empty space preclusion device
How often should universal ammunition loading system (UALS) replenisher assemblies be inspected?
Every 30 days when in use and annually when in storage
In regards to ground transportation, when are nuclear weapons moved by convoy?
Every time weapons are moved
which minimum articles of safety gear must be worn when using a bench grinder
Eye and Face protection
What should you do if a conflict is discovered while using TO 11-1-38 between the illustrations and the written procedures?
Follow the written procedures
What type of steering aids the MHU-226 in a tighter steering radius?
Four-wheel double Ackerman
An Electrical saw blade must be operating at what speed before it contacts the material being cut?
Full
Which 30 mm ammuniton loading system is used to service the GPU-5/A gun pod?
GFU-10/E
which items do not require nuclear safety certification for use in operations with nuclear weapons?
General-purpose hand tools
what category or categories are Air Force air compressors classified?
High or low pressure
Which subassembly of the universal ammunition loading system (UALS) provides the means to load live rounds into the aircraft gun system?
Interface Unit
Which component of the munitions assembly conveyor (MAC) can be used as a forklift adapter to raise the gantry to full height?
Interface control board (ICB)
What source is best use to determine the explosive hazard class/division of a specific munitions item?
Joint Hazard Classification System (JHCS)
What is the most difficult job for escort guards during a convoy?
Keeping other vehicles from entering the convoy
How is the yaw positioning from the cradle or boom controls of an MJ-1 lift truck adjusted?
Manually
What provides an itemized list of all equipment authorized for use with nuclear weapons?
Master nuclear certification list
which area is designated as a location used temporarily during a delay of an off-base movement involving nuclear weapons
National defense
when is it permissible to transport explosives in privately owned vehicles (POV)
Never
The annunciators displayed on the Fluke 8025 series millimeter are used to distinguish among.
Ohms, Kilohms, and megohms
which statement about pintle hooks and their use in operations with nuclear weapons is correct?
Original equipment pintle hook assemblies are authorized
Which subassembly of the universal ammunition loading system (UALS) provides the power that cycles the rounds through the system?
Pneumatic regulator
Once verified that an item is nuclear certified, how is it identified as such?
Positive identification by a nameplate, label, appropriate marking, or by official documents
What should be worn anytime there is a potential for injury from overhead objects during a lifting operation.
Protective helmets
What are the two operational modes of the Fluke 8025-series multimeter?
Range and hold
What code word is used when department of Energy (DOE) convoy seeks sanctuary during an emergency?
Safe Haven
what are the key factors to consider during a nuclear weapons movement?
Safety and security
what does Title 49 of the code of federal regulations (CFR) regulate?
Shipments of hazardous material, including explosive within the United States
what piece of equipment must be used with the MHU-110 to prevent the trailer from becoming unstable while using the rail extenders for loading or unloading heavy munitions?
Stabilizer jacks
Which weapons replaceable assembly of the Linkless Ammunition Loading System (LALS) has no moving parts?
Storage container
what is the purpose of the trailer hand valve ( Johnson Bar)?
Test the trailer brakes
When the MHU-141 trailer is loaded or towed with the hinged deck open, what must be done?
The deck-panel supports must be properly positioned and locked in place with quick-release pins.
what is the primary focus when designating primary and alternate explosive movement routes?
Use the safest possible routes
what type of information is given in the general notes on the first card of each trailer and weapon-type section in TO 11-1-38 and is required to be reviewed?
WARNINGS,CAUTION, and NOTES pertaining to each trailer and weapon.
What is the most common type of lifting sling used in the munitions career field?
Wire rope
Which action is not an authorized method for securing loose lengths of chain when using the MB-1 tie down device/ chain assembly?
Wrap the loose ends around the tie down device and secure to the quick release lever
If you cannot fully close the load-binding handle by hand,
adjust the load-binder hooks on the chain
What is the most beneficial attribute of using the swingmaster forklift?
allows you to maximize the available storage space.
What happens to the unfired rounds returning from the loader when the linked ammunition is being processed?
automatically downloading through the second gate in the bottom of the replenisher
The purpose of cutting lubricant in most drilling operations is to increase the
drilling speed and the drill bit life
what is the primary drawback to using the hydraulic hand pump to build hydraulic pressure on the MHU-83 series lift truck?
extremely slow way to build hydraulic pressure
When packing up munitions assembly conveyor (MAC) it is important to cap the ends of the air hose to keep
foreign materials from damaging them.
The following are all good safety practices to follow when using a lifting sling except
inspecting the sling by passing your bare hand over the body of the sling
When using a load binder for securing a load, what is the main reason for not using a cheater bar or extension tool to fully close the handle
it would place too much pressure on the load and/or tie-down points
what gear range should be selected in a tractor with an automatic transmission while going downhill?
low range
what is the purpose behind good operator maintenance of all assigned vehicles?
maintain vehicle serviceability at reduced cost
Which subassembly of the universal ammunition loading system (UALS) house a remaining indicator window that provides the means to visually determine the approximate number of rounds in the unit?
outer drum
The purpose of the transport beam beneath the lift arm assemblies on the MJ-1 series lift truck is to
provide added support and to relieve hydraulic pressure from the lift arms when carrying loads for long distances
The parking brake on the MHU-110/M is applied by
pulling either one of two hand levers located on each side of the front of trailer.
when using the MHU-83 series lift with fork adapters, you immediately
reduce the lifting capability by 1000 pounds
What USAF gun system is loaded and unloaded by the Linkless Ammunition Loading System (LALS)
the M61A1, 20 mm Cannon
what happens when you release the accelerator pedal on vehicle driven with a hydrostatic transmission?
the unit coast to a stop very quickly
How many openings (hinged door panels) are on the deck of the MHU-226 trailer?
three
The triple bomb bar is fitted with bomb slings and is used with each hoist to provide for lifting
three 500 pounds munitions at a time or two 2000 pound munitions items
What are hose couplers (glad hands) used for on tractor/trailer combinations?
to connect the service and emergency brake airlines from the tractor to the trailer
Pintle safety locking pins must remain attached to the pintle assembly
to prevent an unsecure pin from coming out and getting lost.
Which procedure is not a consideration for backing a tractor/trailer combination?
turn toward the passenger's side.
what can be constructed and attached to the bed of a 40-foot trailer to facilitate support of round munitions?
wooden rail sets
