Chapter 1; Green Book

Pataasin ang iyong marka sa homework at exams ngayon gamit ang Quizwiz!

When using the architect's scale, the ___ should always be placed on the beginning of the line being scaled.

0.

Interior doors for one-family and multifamily dwellings must be at least ___" thick.

1 3/8"

___ is a method of viewing an object in a pictorial form.

Layering.

The front view of an orthographic projection shows the ___ and height of an object.

Length.

HVAC information for commercial buildings is generally shown on ___ plans.

Mechanical.

Elevations are ___ drawings showing vertical planes of a building.

Orthographic.

___ is the relative size to which an object is drawn.

Scale.

A(n) ___ is created by passing a cutting plane through a portion of a building.

Section.

The ___ Elevation is the view of the south side of a building, not the direction a person faces to see that side of the building.

South.

The most commonly used scale for working drawings is ___.

1'-0" = 1/8"

A(n) ___ line is utilized to show that a detail continues but is not drawn.

Break.

T/F Hollow-core doors may be used for any room or any entrance of a one-family dwelling.

False.

T/F The keyed side of a lock is considered the inside for doors that open between rooms.

False.

T/F The minimum riser height for a commercial stairway is 6".

False.

T/F The two general types of doors are flush and panel.

False.

T/F When the same size and type of windows are shown on a drawing, the dimensions and light size of each are provided for clarity.

False.

T/F Window components are shown in detail on floor plans.

False.

T/F Working drawings include all of the information needed to construct a building.

False.

Cutting planes for sections are generally shown on ___.

Floor plans.

Lines below a surface or behind an object are drawn as ___ lines.

Hidden.

Flush doors may be either solid-core or ___-core.

Hollow.

Window height above a finished floor is usually indicated to the bottom of the top window ___.

Jamb.

Orthographic projections are also referred to as ___ drawings.

Multiview.

When determining door hand, the viewer is considered to be standing on the ___ of the door.

Outside.

The location of all exterior walls and interior ___ are shown on floor plans.

Partitions.

___ plans show the location of existing buildings on the property.

Plot.

The total ___ of a stairway is its total height.

Rise.

Dimensions on a print show ___.

Size, location, and size relationship of parts.

A legal ___ is required to establish the corners or a building lot in relation to official points of measurement in the vicinity.

Survey.

Complex building parts such as doors and windows are simplified and drawn as ___.

Symbols.

Exit passageways must be at least 44" wide except when serving an occupancy load of less than 50.

True.

Four elevations are generally sufficient to clearly show exterior walls of a building.

True.

Interior doors generally require only two hinges.

True.

T/F A floor or landing is required on each side of a door.

True.

T/F A section through the side jamb on a window detail is a slice through the jamb looking down.

True.

T/F Casement windows swing outward.

True.

T/F Concrete walkways and driveways are shown on plot plans.

True.

T/F Details may be part of a plan view, elevation, or section drawn at a larger scale.

True.

T/F Dimensions should not be repeated on prints unless marked REF.

True.

T/F Door openings on plan views are dimensioned in a manner similar to window openings.

True.

T/F Exit passageways must be a minimum of 44" wide except when serving a capacity load of less than 50 people.

True.

T/F Floor plans are generally the most used plans in a set of prints.

True.

T/F Location of water, sewer, and electrical power is generally indicated on plot plans.

True.

T/F Plumbing fixtures are generally shown on residential floor plans.

True.

T/F Software is the operating system of a CAD system that allows hardware components to interact.

True.

T/F Symbols may be used on floor plans and elevations but should not be used on details or sections.

True.

T/F The hinged side of a window is shown by the apex of a dashed triangle drawn on the window in an elevation.

True.

T/F The most common sections are taken through exterior walls.

True.

T/F The unit rise of a stairway is the height of each riser.

True.

T/F Windows in masonry walls are generally dimensioned to the edge of the opening.

True.

T/F Written information is often found in the title block.

True.

Only ___ letters are used for abbreviations on working drawings.

Uppercase.

The conventional representation for stairways on plan views is a series of ___.

Vertical lines representing risers.

The number 30/48 near windows shown on a set of prints indicates that ___.

Window lights are 30" wide and 48" high.

The three classifications of ___ are fixed-sash, sliding-sash, and swinging-sash.

Windows.

Conventional representation of lines used for drawings is prescribed in ANSI ___.

Y14.2M

___ ordinances restrict the use of land to particular types of businesses or dwellings.

Zoning.

Hidden lines are drawn with ___" dashes and 1/32" spaces.

1/8"

The vertical distance between residential stairway landings should not exceed ___'.

12'

A ___ degree angle is formed between the axes in isometric drawings.

120*

Cross-sectional areas of handrails must not be less than 1 1/4" nor more than ___".

2"

The minimum clear width of an exit door is ___.

3'-0"

The minimum size of an exit door is ___ wide by 6'-8" high.

3'-0"

The preferred angle for a stairway is between 30* and ___*.

35*

Interior frame partitions with a gypsum board finish on floor plans are usually indicated as ___" thick.

4"

The cutting plane for a floor plan is generally taken ___ the floor being shown.

5'-0" above.

Minimum headroom required for a stairway is ___.

6'-8".

The ___ has the responsibility of providing all required dimensions for the plans.

Architect.

___ terminate dimension lines.

Arrows, dots, and slashes.

Building ___ specify types of materials that must be used for particular aspects of construction.

Codes.

Finished grade is shown on a plot plan with ___ contour lines.

Dashed.

___ contour lines show existing grade.

Dashed.

___ may be drawn of any part of a building that is not clearly shown on the prints.

Details.

___ are shown to locate points from other points on the prints.

Dimensions.

E

East.

EL

Elevation.

ENT

Entrance.

For a hazardous area or when the occupancy load of a building exceeds 50 occupants, ___.

Exit doors must swing in the direction of travel.

Dimension lines are terminated by ___ lines.

Extension.

The abbreviation for "foundation" is ___.

FDN.

Hollow-core doors have a core of wood blocks

False.

T/F A casement window is a type of sliding-sash window.

False.

T/F A centerline and a cutting plane are drawn with the same linetype.

False.

T/F A standard abbreviation on a print can have only one meaning.

False.

T/F All drawings on a single print sheet must be drawn to the same scale.

False.

T/F All information about windows is shown on floor plans or section views.

False.

T/F An extension line is always terminated by an arrowhead.

False.

T/F As the space between contour lines increases, the lot becomes steeper.

False.

T/F Dimensions indicating the exact room size should be shown in each room on a floor plan.

False.

T/F Elevations are always drawn to the same scale as floor plans.

False.

T/F Exterior elevations are used to show cabinet details.

False.

T/F General information pertaining to drawings on several sheets in a set of prints must be included in the title block.

False.

T/F Hollow-core doors have a core of wood blocks.

False.

T/F Steep stairs have wide treads and low risers.

False.

T/F Symbols are not used on sections in order to avoid confusion on the drawings.

False.

T/F The abbreviation for "center" is CNT.

False.

A right-hand door hinges on the right and opens ___.

Inward.

Extension lines define size or ___.

Location.

All visible print lines are shown with ___ lines.

Object.

Drawings completed with ___ projection techniques are commonly referred to as multiview drawings.

Orthographic.

___ plans show the location and orientation of a building on the lot.

Plot.

R

Riser.

RF

Roof.

___ hinges are required to hang on solid-core doors.

Three.

A ___ block is the logical place to begin reading a set of prints.

Title.

An architect's scale is ___ in shape.

Triangular.

Door hand is the direction in which a door swings.

True.

T/F A code reference near a cutting plane indicates the sheet number on which the identified section is found.

True.

T/F A dimension, without other notion, should only be shown once on a print.

True.

T/F Awning windows swing outward.

True.

T/F Blueprints have white lines on a blue background.

True.

T/F Pictorial drawings show height, length, and depth of an object.

True.

T/F Prehung doors include the door frames and hardware.

True.

T/F The diazo print process produces black lines on a white background.

True.

T/F The use of hidden lines on working drawings is minimized to avoid confusion.

True.

WC

Water closet.

W

Water.

WP

Waterproof.

WS

Weatherstripping.

WD

Wood.

A door designated 2'-8" x 6'-8" x 1 3/4" ___.

may not be used as an exterior door, is a right hand door, and is not a flush door (none of the above).


Kaugnay na mga set ng pag-aaral

Chapter 22: Management of Patients with Upper Respiratory Tract Disorders (2)

View Set

ASQ - Ch 8 - Management Skills & Abilities (P 132 - 198)

View Set

Pharmacolog test 2- Adrenergic AgonistsDrugs that produce activity similar to the neurotransmitter norepinephrine are known as which of the following?

View Set

FLVS Anatomy and Physiology - Semester 1 - Module 2

View Set

Jason Nguyen- AP U.S. Government and Politics: Chapter 14 Vocabulary

View Set

Social Psychology Chapter 12 - Learning Objectives

View Set