OSHA 30 Final Exam Review
Sections _____________ of the Safety Data Sheet (SDS) contains general information about the chemical, identification, hazards, composition, safe handling practices, and emergency control measures.
1 though 8
Nearly ___________ of all serious occupational injuries and illnesses stem from overexertion of repetitive motion
1/3
Citations must be contested within __________ working days of the notice of proposed penalty.
15
All employers covered by the OSHA Act are covered by part __________ regulation, which required employers to record and report injuries and illnesses.
1904
Flammable liquids have been updated and divided into ________ categories.
4
The employer must comply with an employee's or employee representative's request to examine and copy abatement documents within
5
Safety footwear must _________ minimum compression and impact performance standards.
ANSI
Make sure to keep ___________ clear of obstructions to prevent worker injuries and damaged materials.
Aisles and passageways
A permit-required confined space may be reclassified as a non-permit confined space under which of the following conditions?
All of the above
All employees required to enter a confined space should be informed of ______________
All of the above
An emergency action plan contains which of the following?
All of the above
Chemicals are classified as health hazards when they pose which of the following hazardous effects?
All of the above
Employer provided PPE training should include information about:
All of the above
Lockout devices and tagout devices must be :
All of the above
Noise can be reduced by:
All of the above
Power cord can be damaged by which of the following?
All of the above
Types of heat illness include?
All of the above
When left on the floor, which of these will create tripping hazards?
All of the above
When must Exposure Control Plans be updated?
All of the above
Which of the following are flammable gases?
All of the above
Which of the following does the lockout and tagout standard not apply to?
All of the above
Which of the following is a function of a safety device?
All of the above
Which of the following is an example of Hazardous Materials?
All of the above
Which of the following is an exception to the general rule for safeguarding to prevent hazards during servicing and maintenance of machines?
All of the above
Which of the following motions is commonly cited as a cause for back injuries?
All of the above
With the use of calibrated direct-reading instruments, which of the following can be tested in the internal atmosphere of a confined space?
All of the above
You should change your working position frequently by:
All of the above
Which of the following should employers prevent in order to ensure the safety and health of workers in regards to machine guarding?
Allowing workers to use a machine without training
When using eye and face protection you should do all of the following except:
Always remove contact lenses or glasses before use
Ground-fault circuit interrupters must be used for all of the following except?
Any outdoor area
For personal fall arrest systems all of the following apply except:
Are not required to be paid for by employers
Which of the following is the definition of point of operation?
Area on a machine where the work is performed
An emergency response coordinator is responsible for all of the following, except:
Attempting to put a fire, no matter the size
When a hard hat sustains an impact, it should :
Be replaced
Rigging equipment should be proof tested _____________ use to ensure it can handle the loads it will be used for.
Before
Which of the following is most likely to cause a fall
Being too far off of your center of balance
Which of the following is not a possible method of transmission for Hepatitis B, Hepatitis C, or HIV?
Blood splash on properly secured PPE
What requirements are necessary to protect an electric tool user from shock?
Both A and B
Which of the following is manual material handling?
Carrying a heavy tool
Which class of fire extinguisher would be best suited to put out a wood fire?
Class B
Which of the following is not an example of a hazard?
Clean, dry floor surfaces
Empty oxygen cylinders must have their valves:
Closed
Which is NOT protection again poisonous gases.
Closed windows
Which of the following is not a responsibility of a fire watch?
Complete tasks not related to fire watch duty in the work areas
An employer must have and maintain an employee alarm system that _____
Consists only of an audible warning
The leading cause of slips, trips, and falls is
Contaminants on the walking surface
Which is not an insulator?
Copper
Which of the following is not an example of rigging equipment?
Crane
Which of the following is an example of an electricity hazard?
Damaged extension cords
Which of the following is a description of a pullback device?
Device that uses cable attached to hands which allows access to the point of operation when the slide/ram is up and automatically withdraws hands when the slide/ram begins to descend..
Which is NOT an acceptable method for removing or transferring a flammable liquid from a container?
Device to draw liquid from the bottom
Who is responsible for the safe conditions of tools and equipment used in the workplace?
Employers
PPE is used when _______, ________, and _______ controls are not possible or do not provide suitable protection for workers.
Engineering, work practice, and administrative
The 3 parts of an exit route are the exit access, exit, and __________
Exit discharge
Safety belts, lifelines, lanyards, and Personal Fall Arrest Systems are all examples of:
Fall protection equipment
All portable, power-driven circular saws having a blade diameter greater than 3 in. must be equipped with guards above and below the base plate or shoe
False
Cylinder valves must be immediately repaired or sealed if an operator discovers a malfunction.
False
Employees who wear personal protective equipment do not need safety and health training.
False
Employers are not required to have conspicuously posted OSHA notices informing employees of their protection and obligations, and for assistance and information.
False
Engineering controls are the last strategy of control an employer should use for job hazards.
False
Following the application of lockout or tagout devices to energy isolating devices, all potentially hazardous stored or residual energy must be relieved.
False
Hand tools are powered instruments, which can be very hazardous when improperly used due to their power source.
False
Hydraulic jacks exposed to freezing temperatures must be kept warm with an internal temperature lift.
False
In circumstances for which it is impossible to provide such ventilation, airline respirators or hose masks approved for this purpose by OSHA must be used.
False
Industrial hygiene is the science of keeping yourself favorable to health, free from dirt, bacteria.
False
It is not necessary that the lockout or tagout process is performed only by the authorized employees who are performing the servicing or maintenance.
False
Lockout/tagout establishes the maximum performance requirements for the control of such hazardous energy.
False
Pushing carries a greater risk of strain and injury.
False
Reporting symptoms of MSD early does not help in stopping MSD.
False
Under OSHA, employees are not protected from discrimination when reporting a work-related injury, illness, or fatality.
False
When implementing a safety and health program, management leadership does not need employee participation.
False
Which of the following is a type of machine safeguarding?
Feeding and ejection methods
Which of the following types of machine guard is generally preferred because of its simplicity and durability?
Fixed
The ___________ pictogram is used to warn about the oxidizer class of chemical hazards.
Flame over Circle
Acetone is a __________.
Flammable liquid
What is the main danger associated with pneumatic tools?
Getting hit by tool's attachment or fastener
Which of the following is not a correct general precaution that should be followed by all power tool users?
Handle tools by the cord or hose
OSHA requires that employers pay for most required personal protective equipment (PPE), including:
Hard hats
It is not safe to carry out work tasks on a walking or working surface that
Has inadequate lighting
Supervisors must protect combustibles from ignition by using which of the following procedures?
Have the work moved to a location free from dangerous combustibles
Which of the following is the general definition of Hazard Communication?
Hazard Communication is all about analyzing chemical components and testing for chemical hazard to ensure a safe and healthy work environment.
Employers should use data form the ________ when selecting appropriate PPE.
Hazard assessment
Which of the following types of protection is an employer required to pay for?
Hearing protection
Which of the following has a vaccine?
Hepatitis B
Age, fatigue, inattentiveness, eyesight, and footwear are ----- that can contribute to slips, trips, and falls.
Human factors
Uncontrollable shivering, loss of coordination, and slurred speech are symptoms of what?
Hypothermia
Employers should follow these three steps for putting a Hazard Communication program into practice:
Identify responsible staff, identify hazardous chemicals, and prepare and implement the program
An exit sign must be:
Illuminated by a reliable light source
What type of OSHA inspection is conducted when immediate death or serious harm is likely?
Imminent danger
Hazard prevention and control includes
Implementing administrative and engineering controls
Effective management of worker safety and health programs has
Improve employee productivity and morale in the workplace
Around 20 to 25 percent of forklift-related injuries were related to ________?
Inadequate training
What are bloodborne pathogens?
Infectious microorganisms present in human blood
An important safety precaution to remember when operating powder-actuated tool is:
Inspect it before use and determine that it is clean and that all moving parts operate freely
What is grounding?
Intentionally creating a low-resistance path that connects to the earth
An example of a possible source of ignition includes all of the following EXCEPT:
Leaking water pipe
Which of the following is not a method of securing stacked materials?
Leave nails in when stacking wood
Which of the following is mechanical material handling?
Lifting something with a crane
What was the main factor that contributed to the loss of life in the Triangle Shirtwaist Factory tragedy?
Locked stairwell doors
Where appropriate, the employer must provide the following materials for isolating, securing or blocking machines or equipment from energy sources:
Locks/Tags
The ______________ the flashpoint, the ____________the hazard.
Lower, Greater
Which of these is not a type of ground Fault Circuit Adapter?
Manual
Any part of a machine which __________ while in operation can cause a hazard.
Moves
The following are all machine safeguarding requirements except:
Must prevent workers from lubricating a machine without removing the safeguard
All container of hazardous chemicals leaving the workplace must be labeled, tagged, or marked with the following information except?
Name, address, and telephone number of employees using chemical at worksite
Which of the following guards against exposure to electrical hazards?
Non-conductive footwear
Which of the following is not an example of a fire hazard?
Obstructed exit door
A/an ______ is a unit of measurement for electrical resistance.
Ohm
Conductor insulation must be approved for the ________ of use?
Operating Temperaure
__________ Must not be stored near highly combustible material.
Oxygen Cylinders
The OSHA standards for Construction and General Industry are also known as
Part 1926 and Part 1910
Hazard Communication covers both __________ and health hazard.
Physical
When the employer receives an OSHA citation, it must be:
Posted for 3 days or until the violation is fixed
Which of the following is NOT an example of an ignition source?
Power strip
What is the first step in the application of energy control (lockout or tagout procedures) sequence?
Preparation for shutdown
Which of the following is not an example of appropriate PPE?
Prescription glasses
OSHA's mission is to:
Protect the safety and health of America's workers
The Hazard Communication Standard was modified to adopt the Globally Harmonized System to:
Provide a standardized approach to hazard communication
One of the main responsibilities employers have under OSHA is to:
Provide training required by OSHA standards
Chemicals in the _________ class are liquids which, even in small quantities, are liable to ignite within five minutes after coming into contact with air.
Pyrophoric Liquid
Effective personal protective equipment must be?
Regularly maintained
The right of workers to seek safety and health on the job without fear of punishment is spelled out in:
Section 11(c) of the OSH Act.
Which of the following is not a common type of hazardous mechanical motion?
Shearing
Which of the following is not a category of electrical burns?
Shock
According to OSHA ------ constitute the majority of general industry accidents
Slips, trips, and falls
If you feel that an OSHA inspection is needed to get hazards corrected at your workplace, which is your best option?
Submit a written, signed complaint with specific hazard information.
Which of the following openings does not require guardrails?
Temporary floor openings
Among the rights related to OSHA recordkeeping, workers have the right to review:
The OSHA 300 Log and the OSHA 300A Summary
When does Working Restriction Protection end?
The employee is able to return to his or her regular job or a new position.
The creation of OSHA provided this important right to workers:
The right to a safe and healthful workplace
If a chemical manufacturer, importer, or employer becomes aware of any significant information regarding the hazards of a chemical or ways to protect against hazards, this new information must be added to the SDS within__________ months.
Three
Training is a way for employers to provide ___________ to enable employees to protect themselves and others from injuries.
Tools
Which of the following is NOT a role of industrial hygienists?
Training employees on the recognition of hazards
During emergencies, hazards appear that normally are not found in the workplace.
True
Employees may not enter a confined space until the forced air ventilation has eliminated any hazardous atmosphere.
True
Employees who work in confined spaces face increased risk of entrapment, engulfment, and hazardous atmospheric conditions.
True
Employers are not required to keep a record of an employee who has the flu.
True
Gases are formless fluids that expand to occupy the space or enclosure the are contained in.
True
Helmets or hand shields must be used during all arc welding or arc cutting operations, excluding submerged arc welding.
True
If a hazardous atmosphere is detected during entry, employees must immediately leave the space.
True
If an energy isolating device is capable of being locked out, the employer's energy control program must utilize lockout, Unless the employer can demonstrate that the utilization of a tagout system will provide full employee protection as set forth by OSHA regulations.
True
Implementing an ergonomic process is effective in reducing the risk of developing MSDs in high-risk industries.
True
Lockout devices must be substantial enough to prevent removal without the use of excessive force or unusual techniques, such as with the use of bolt cutters or other metal cutting tools.
True
Safety de-energizing the debarker requires that six electrical sources and one pneumatic energy source needed to be disconnected and locked out.
True
Safety guards must never be removed when a tool is being used.
True
The operating control on hand-held power tools must be located at to minimize the possibility of accidental operation, if such accidental operation would constitute a hazard to employees.
True
Work practice controls include the company's general workplace rules and other operation-specific rules.
True
regardless of how good your working posture is, working in the same posture or sitting for prolonged periods is not healthy.
True
Which of the following presents a sharps hazard?
Uncapped syringe
Which is acceptable when using powered tools?
Use double-insulated tools
Which is a preventive measure to prevent hazards while working with power lines?
Use only nonconductive tools and materials.
Which of the following is an example of an engineering control?
Using self re-sheathing needles
Which of the following is the best method of preventing Hepatitis B?
Vaccination
The act of providing a space with fresh air in place of air that has been used or contaminated is known as what?
Ventilation
Biological hazards are
Viruses
What should be placed near stairs, changes in elevation, and floor openings to prevent accidents and injuries?
Visual cues
Which of the following is an example of ionizing radiation?
X-ray
whenever there is too little friction or traction between your shoes and the floor:
You may slip and fall
------- is likely to cause you to trip and fall
Your foot striking an object in an unexpected way
Authorized entrants who enter a permit space must wear ___________.
a chest or full body harness with a retrieval line
A(an) _____________ is an individual stationed outside one or more permit spaces who monitors the authorized entrants.
attendant
Contaminated sharps must be disposed of in ____________
closeable, labeled, leak-proof containers built to properly contain all contents
The critical parts of a crane, such as operating mechanisms and system components, must be inspected ______________ for any issues or damage.
daily
An employer should order a(an) ______________ of the permit space when a worker shows signs of physiological effects of hazard exposure.
evacuation
Exit routes must be __________ and_______________
free, unobstructed
A Safety Data Sheet (SDS) gives information about:
hazardous chemicals
What does MSD stand for?
musculoskeletal disorders
A method of infection control where all human blood and potentially infectious, regardless of whether they are believed to be infected or not, is called _____________
universal precautions
During an OSHA inspection:
you have the right to talk with the inspector privately.
