PATH
When working as a pilot on a high or wide load, what route is acceptable through Journal Square?
17 TRACK
What is the maximum speed allowed while operating a revenue train through 1 Track in Harrison Yard?
20 MPH
What series of signals are in Tunnel E?
200 even
Where is the shunt indicator located?
22 track, C-Yard
What rule is used to pass an automatic signal at stop and proceed?
253
Which of these statements about yard mode operation is true?
ATC enforces a 12mph speed limit, but the train engineer is responsible for complying with any other restrictions.
The manual cutting lever is located:
Above the draw head
How would you know that third rail power was removed when operating PA4 cars?
Absence of lights, air compressor, and motor power
What must the train engineer do upon leaving CBTC mainline territory?
Acknowledge the territory and operate normally for the territory you are entering.
What does the ATC Door Mode switch do if it is in the Cut-Out position?
It selects that the train engineer will enable the train doors.
What would happen if the control cut-out was in the "OFF" position?
Master controller is dead, no power to traction motor, train will not move
What is the maximum speed through a station when the train will not be stopping?
15MPH
What tracks are in the north yard in Harrison?
1-4
Can a train operating in MATC traverse a Slow Speed Order?
yes
What is the maximum amount of cars that can be displayed on a PA5 TOD screen?
"z/d"-automatic "x"-interlocking
Where are the low-voltage circuit breakers on PA5 located?
#1 end panel board of A and C cars
Where are the TOD screens located on a PA5 "C" car?
#1 end panel boards
Where is the air compressor switch located on PA4's?"
#2 end of a "A" car
Where is the air compressor high voltage breaker located on PA5 car?
#2 end panel board
Where is the brake cut-out lever located on PA4 cars?
#2 side of car, under the seat marked "B", underneath the outside on the #2 side of the car
What brake cylinder pressures are indicated on the PA 4/PA5 and what are the normal readings at full service and full release?
0-60 to 62psi & 0-28 to 39psi
The correct tracks in Harrison Yard are
1 thru 4 5 thru 16 20 thru 30 33 thru 40, 42, 43, 46-49
How many cars fit on 7 track inside Harrison Yard?
10- 5east, 5 west
At Journal Square, B yard contains tracks:
10-17
What signal series are in Tunnel A?
100 even
What signal series is in Tunnel B going uptown?
100 odd
What pressure should the PA4 brake pipe read when fully charged?
110psi
What pressure should the brake pipe read on PA4 cars when your brakes are fully released?
110psi
ATC poses what type of restrictions in Yard mode?
12 mph speed limit
What is the maximum speed through an interlocking under rule 279?
12MPH
What is the normal pressure of the main reservoir on PA4 and PA5 cars?
130-150 psi
What interlocking signal in Harrison Yard can you receive a permissive signal at?
140X, 180X
When does the indication of an approaching Slow Speed Order appear on the TOD?
3,500 feet prior to the Slow Speed order
When does the indication of approaching a work zone appear on the TOD?
3,500 feet prior to the work zone.
Pit speed at the running repair is no greater than
3mph
What is the maximum speed allowed in Tunnels E and F while operating under STDS?
40MPH
What tracks are in the west yard in Harrison?
42,43,46,47,48,49
What tracks in Harrison yard are equipped with derailers?
5 through 16
The correct tracks in JSQ yards are
5 thru 9, westbound intermediate (A yard) 10 thru 17 (B yard) 18 thru 23, 23A, 32, 33 (C yard) 50 thru52 (D yard)
The correct number for .....?
6446 (assignment coordinator) 6078/2677 (PAPD) 3969/3968 (Harrison Yard tower) 7131 (World Trade Center Dispatcher) 6552 (Trainmaster) 7121 (Hoboken Dispatcher) 7161 (Journal Square Dispatcher) 7111 (33rd Street Dispatcher) 7191 (Newark Dispatcher)
When you observe one yellow flag in the track area, reduce your speed to:
8mph
At Journal Square, a train can enter from either direction onto tracks:
9, 12, 15, 17
An active (keyed up) PA-5 is displayed on the TOD screen as:
A green square
Which of the following is not included on the speed dial?
A service brake application triggered by the car-borne ATC
Rule 101 gives you permission to pass:
A signal displaying a double red over solid lunar white light
What is the acceptable position of the ATC Bypass switch when leaving the cab?
ATC
An ATC-equipped train experiences a complete failure of the car-borne ATC equipment while in CBTC mainline territory. In which operating mode should the train proceed after the failure?
ATC Bypass
What is the meaning of a solid yellow light on the exterior of a PA5 car?
Activated PEHU in that car
What are the principal indications of a brake pipe rupture on a PA-4 train?
Air may be blowing from brake valve; brake pipe pressure is greatly reduced, unable to charge the train, and straight air pipe pressure very low.
How many handbrakes are required on the train when you laying up a train at signal R8X in Newark?
All of them
If a contact shoe on a car is in contact with the third rail, how many of the shoes on the car will be considered live
All of them
What will occur if you transition into Release mode while the train is in motion
An emergency brake application will occur
How does the operation of Order Signals (Rule 222) change under ATC?
An indication stating "Call for Orders" is provided on the CBTC-TOD when the train is in approach to a flashing red order signal.
On PA4 cars, what is the correct procedure for uncoupling where there is a cab at the point of the cut (cab to cab)?
Apply hand brakes on section left behind, remove safety chains, charge train, put reverser key in desired position, insert cutting key, lift key to uncoupling position, release brakes, depress the Motorman's Bypass, apply one point of power to the Master Controller, buff the cars, shut off the controller, put reverser key in the reverse position, depress the motorman's bypass, apply one point of power to the master controller, notch cars away. Separate train apply brakes.
What are the correct steps you would take when you are removing bus jumpers?
Apply handbrakes. Have power removed. Verify power removal. Open latch. Remove jumpers from receptacles on both sides. Place jumper on flat or train. Have power restored. Verify power is restored. When sufficient air is built up, release hand brakes and proceed
What are the correct steps you would take when installing bus jumpers?
Apply handbrakes. Inspect bus jumpers and receptacle for damage. If damage is found, do not use. Have power removed. Verify power is removed. Open latch and insert jumper fully into receptable. After inserting jumper into both sides, have power restored. Verify power is restored. Charge train. When sufficient air is built up, release hand brakes and proceed.
If an engineer has to go beneath his/her equipment, what precautions should be taken?
Apply sufficient hand brakes, pull emergency cord/PEHU, have power removed
What safety equipment should an engineer wear or carry?
Approved safety shoes, safety vest, gloves, glasses, hard hats (when working on equipment where required), any protective equipment, and flashlight
What is the allowable speed for passing a flashing green or flashing yellow ATC signal?
As displayed on the TOD
In the event that you will be late for the start of your job, you must contact the
Assignment Coordinator
When must an engineer display high beams?
At all time while operating outside of the tunnels and entering "H" platform in Newark.
Where are the side inclines located?
At turnouts
When a triangle appears alongside the MAL bar, which of these is present at the location indicated by the triangle?
Beginning of a slow speed order or work zone
Where is the motor control cut-out switch located in a PA4 car?
Behind the engineer's seat in a closed compartment
When readying a car(s) for movement from a shop track, list items to be checked before the car(s) are moved or added t
Blue flags/ lamps removed, personnel on or about the equipment, tools removed, chocks and obstructions are removed, brakes on the cars are cut-in, all angle cocks opened, all electrical portions are centered, wall trolleys removed, knife switches closed, and all compartments closed. (drumswitches on PA-5 cars)
During an FRA Class II air brake test on the PA5 trains, which gauge will move to zero when the engineer moves the controllers to "coast"?
Brake Cylinder
The emergency pipe on the PA5 is called the ___________on the PA-4 cars.
Brake Pipe
The term BIE: PEHU on the PA5 TOD trouble screen indicates what type of problem?
Brakes in emergency due to passenger emergency handle unit being activated.
How can you differentiate the #1 end of a C car?
By looking at door numbers 1 and 7, looking for the letter "F", where the alarmed enclosure is located
When working as a pilot, you should....
Call clear of the interlocking when clearing the reverse signal associated with the interlocking
What is the correct procedure to pass an automatic signal displaying the letter "z" in the stop and proceed position?
Call for permission to pass from the trainmaster. The engineer must also request permission to change form current CBTC operating mode to release mode before proceeding. After receiving permission, the engineer must stop the front end of the head car in line with the face of the signal to clear the automatic train stop. If the stop arm fails to clear, it must be forced down by the conductor and secured by hook. The train may them proceed at restricted speed to the next signal. Change back to CBTC MCS mode when "CBTC" available appears on the TOD.
What is Release mode used for?
Closing up to a train ahead, approaching standing cars in preparation for coupling on mainline, coupling or uncoupling on the mainline, switching moves in CBTC yards, switching moves in non-CBTC yards, accepting a "call-on" (Restricting Signal aspect) at an interlocking signal, ATC is unable to permit the movement due to a failure, track circuit failure, other STDS failure resulting in a signal being unable to clear, CBTC failure of the zone controller, communications failure between carborne and wayside equipment, carborne CBTC failure.
What should the engineer do if he/she encounters Rule 231 temporary speed restriction signs, but there is not Slow Speed indication on the TOD and the engineer is operating in MCS mode?
Comply with Rule 231 and follow the posted speed sign. Notify the Trainmaster.
When on trains, in stations, or in terminals, employees must report expended fire extinguishers.
Control and/or Communications
ATC-equipped trains are localized using?
Data read from wayside transponders
What are the indications of a Straight Air rupture on a PA-4 train?
Depending on the location of the rupture, the straight air pressure will register between 45 and 60 pounds when brake handle is in FULL SERVICE (charge) position. Another indication is a very slow loss of brake pipe pressure
In bypass, what actions should you take if overrun a station by half of a car?
Do no press Door Enabler, inform conductor/trainmaster
What breakers do you cut out if your PA4 train is bucking?
Dynamic Brake and Motor cut-out
In what tunnels is Washington Street shaft located?
E and F
What is the master controller (MC) positions on the PA5?
EMER brake, FS brake, MIN brake, COAST, Min power, INT power, MAX power
The meaning of the above the key on "W" means:
East of the key switch on track G
What are the different ways you can have power removed?
Emergency alarm box (gamewell), Call the trainmaster/ train dispatcher
The ADCL light on PA5 cars is known as the ____________on PA4 cars.
Engineer's indication
Where is signal 788Z located?
Entering B Platform in Newark
When is it required to push the ATC Start button during MATC operations?
Every time the train comes to a full stop
How many cars fit on 5 Track west in Harrison Yard?
FOUR
What must all employees have to enter the track or tunnel area?
Flashlight, safety vest, safety shoes, and safety glasses
What are the correct steps you would take when you are removing a wall (auxiliary) trolley from a car:
Follow the wall trolley cable from the car to the attached cable box. Shut off switch box. Remove trolley. Close knife switch. Close knife switch compartment. Hang trolley to the corresponding box.
Train orders are issued:
For movement of work trains, self-propelled and hi-rail vehicles, and to identify work limits.
The emergency pipe on the PA5 will not charge unless the reverser switch is in the _________position.
Forward
As per rule 156 what is the proper whistle when calling for a signal?
Four Long
What is the proper buzzer to use for an airbrake test or to apply or release the brakes?
Four Long
Parking brakes can be applied on the PA5 cars:
From any engineer's cab with an active master controller.
What tunnels are you going to be operating in going against traffic from Grove St to Hoboken?
G,K,F,B
Train engineer operating in MATC is instructed to change his/her operating mode to MCS because a maintainer is in the track area ahead. The engineer will:
Grab/turn the master controller, begin to take it out of FS/BRK and change ATC Mode switch to MCS while the train is in motion and proceed normally.
A white light on the exterior of the car indicates:
Handbrake or parking brake applied on that car.
How do you perform a Class 1A FRA air brake test?
Have the conductor walk around the outside of the train while you apply and release the brakes
PA5 train crew communication is done by:
ICS
What should a train engineer do if the Out of Service indication appears on the CBTC-TOD?
If the Out of Service is part of the scheduled operation, remove the train from revenue service as planned.
IF the "ATC Failure" indication appears, and no other disruption to operation is noted, the train engineer should:
Immediately inform the trainmaster and follow his/her instructions.
What should a train engineer do if the Daily Test has failed?
Immediately report it to the trainmaster and await further instructions
Where are permissive signals located?
In Harrison Yard only
Where is the location of the ATC bypass switch?
In a locked compartment in the engineer's cab & In Conductor's operating section
ATC Bypass mode is?
In bypass mode, the maximum allowable train speed is 40 mph
The motor reset button in PA4 cars is located?
In front of the engineer between the brake handle and master controller
What is the closed position of angle cocks on PA5 cars?
In line with the running rails
Where is the emergency pry/crow bar located on PA5 cars?
In the alarmed enclosure, #1 end
Where is the control cut-out breaker located on a PA4 car?
In the low voltage panel, behind the engineer's seat
As a train engineer, on inspecting the ATC Bypass switch when preparing a train for service, you find the seal is missing. What should you do?
Inform the trainmaster (or yard foreman) that the seal is missing.
What is meant by the term "signal indication"?
Information conveyed by the signal aspect
To charge a PA5 train, the correct procedure is?
Insert MC key and turn to the RUN position, place Reverser switch to the Forward position, move Master Controller handle from emergency to full service position.
On a PA5 train ready for passenger service, the drum switches at both operating ends must be in the _________position.
Isolate
Where is 17 track in Harrison Yard located?
It doesn't exist
How does the train engineer know the current operating mode?
It is displayed in the upper-left corner of the CBTC-TOD
What must you check before you energize the overhead trolley?
It's location, whether it's connected to a car, whether it's "ON", damaged/red tagged, and whether someone is using (holding) it
What should you check before using a wooden slipper?
It's not wet or cracked
No verbal or written order is considered in effect until
It's read back in its entirety.
The Washington Street emergency exit is located between:
Junction 5 and Newport in Tunnels E and F
What is the purpose of a station restriction?
Keep trains from entering station unless they can fully berth and keep trains from departing stations unless they can fully clear the platform.
The best strategy for operating a train in MCS mode?
Learn each section of the road thoroughly so that you can anticipate exactly the speed profiles under CBTC operation. This way, you can keep out of the yellow zone. Also be ready to slow down as you approach the end of a MAL and use the CBTC audible alert to decide exactly when to begin braking.
What are the indications that CBTC caused an emergency brake application?
Loss of MAL and disk is red
Which of the following are positions of the ATC mode switch?
MATC, MCS, Release
A train hold can only be removed in which mode so that the train can proceed?
MCS
What is the acceptable position of the ATC mode switch when leaving the cab?
MCS
What is the normal position of the ATC Mode switch while in yard territory?
MCS
What position of the ATC Mode switch is used when transitioning between territory types?
MCS
What position of the ATC mode switch is used when transitioning between territory types?
MCS
Flashing green signals are displayed for approaching trains that are which of the following operating modes?
MCS and MATC
What is the correct order of steps to take in event of a brake pipe rupture?
Make sure the deadman valve is not operated. Turn off blowers, place brake handle upside down, move valve into FULLSERVICE (charge) position. Remove brake handle and reverser key form cab. Check for activated emergency brake valve or stuck open trip cock, by listening for escaping brake pipe pressure in each car. If escaping air is noted, reset operated emergency brake valve or tripper cock in that car, reset brake valve and proceed. If trouble persists due to broken brake pipe, go to the rear of center car. Close all angle cocks and retrieve electrical portion. See what section of the train charges. If the head section charges the problem is in the rear. Bleed off the brakes in the rear section by pulling up brake cylinder cutout handle in each car of the rear section. Return to head section of the train and reset brake valve. Recharge and proceed with caution to the next station and offload passengers. If the head section fails to charge, the problem is in the head section. In this case, bleed off the brakes in the head section by pulling the brake cylinder cutout handles in each car of the head section, reset the brake valve and charge the train from the rear section and proceed to the next station under flag using extreme caution and off passengers. You must have equal or better number of cars in the good section in order to move the train. IF not, by prepared to couple to a rescue train.
What are the three keys needed to fully operate the PA-5?
Master Controller, Vapor, Door Key
Employees in the track area must be alert for:
Movement of trains in either direction
Can the train engineer select release mode on their own authority?
No
Will a train in ATC Bypass have flashing green signals displayed?
No
Engineer must be in their operating cab, ready to proceed:
No less than two minutes before scheduled departure.
Some curves are protected in the pre-ATC signal system by timed signals that will clear when an approaching train operates in compliance with the speed limit. Will similar protection be provided in ATC Bypass mode
No, the new ATC signal system (STDS) does not include timed signals. The engineer is fully responsible for complying with speed limits set forth in the Book of Rules and any special instructions
Is there any difference for train operation between CBTC and non-CBTC yard territory?
No, the train operates in yard mode under the train engineer's control.
In Bypass, if a train loses its air entering a station, the engineer should:
Not press door enabler and notify Trainmaster
What is speed is restricted speed?
Not to exceed 12 mph
What would have happened if one attempted to cross a territory boundary with the ATC mode switch in the Release position?
Nothing, the train would proceed without interruption into the new territory
What action must be taken if the master controller is stuck in the ON position on a PA4 train?
Notify Control. Controller must be depressed at all times. Place "control cut-out" circuit breaker to "OFF". Brakes can now be applied normally. If power can not be removed place brake handle into emergency position to remove POWER. Do not operate train from that cab. Try forcing the controller off and operate from the next cab in the direction of travel using motorman's bypass under flag. If not, operate train using control cut-out, by placing it "on" and "off".
What are the correct steps you would take in the event of a main reservoir rupture on a PA4 train?
Notify Trainmaster. When loss of motor power occurs, bring train to a stop. Place brake handle in FULL SERVICE (charge) position until brake pipe pressure returns to normal (90 to 110 pounds). Release brake and proceed. Check all air compressor switches. If problem is not corrected, operate from the next cab in the direction of travel under flag using motorman's bypass. If brake pipe pressure falls below 90 pounds, and sufficient braking power can not be maintained, treat same as brake pipe rupture.
What steps are required by the train engineer if the train makes an improper station stop (long) in MCS mode and the train doors in the rear section need to be opened?
Notify the Trainmaster. With permission the train engineer must select the Cut-Out position of the ATC Door Mode Switch, and then enable the doors on the correct side of the train.
What are all the position of the master controller on PA4 cars?
OFF, fast, medium, slow, switch
When must a Class II brake test be performed?
On all trains at all times prior to departing the terminal, whenever the control stand used to control the train has changed, when the scheduled dwell time is 5 minutes or more, or when there is no face to face relief to verify the test was successfully complete
The parking brake manual release handle on the PA5 is located:
On the #1 and #2 end of every car in a locked compartment
As per rule 156 what is the proper whistle to use to apply brakes or stop?
One long
As per Rule 156 what is the proper whistle when running against traffic, use when approaching stations, prior to any use of 156 (g), entering onto an against track, entering blind curves when workers may be present?
One long, one short
What is the whistle signal used when running against traffic?
One long, one short
Who can remove a blue flag?
Only the person that put it there
When operating in Bypass, when does an engineer activate the Door Enabler?
Only when the train has come to a complete stop at the proper car marker.
What should you do if you encounter On-Track Safety flagging, but there is no indication of a "work zone" on the TOD?
Operate according to the flagging posted, inform Control.
If the CBTC TOD fails while the train is moving, and no emergency brake application takes place, the most appropriate response would be?
Operate the TOD selector to "Backup" and notify the trainmaster
What should a train engineer do when operating in MCS mode and he/she has a work zone indication on the TOD with no flagging on the wayside?
Operate the train and comply with the flagging. Notify the trainmaster.
What is the corrective action taken in event of a straight air rupture on a PA4 train?
Operate train normally, but under caution to terminal and notify the trainmaster. ("Note": If Brake pipe pressure falls below 90 psi and sufficient braking power can not be maintained, treat brake same as Brake Pipe rupture.)
Release mode can be used to?
Pass a signal under 279, 101, 253
What is the meaning of a white strobe in the track area?
Personnel working in the track area
How do you place a portable hand trolley to a car?
Place once end on the contract shoe first, then the other on the third rail.
What is the meaning of a solid blue light on the exterior of a PA5 car?
Possible dead motor/ propulsion not operating on that car
What should the engineer do if a Slow Speed Order is indicated on the TOD with no Rule 231 signs on the wayside?
Proceed according to the Slow Speed Order. Contact the Trainmaster
How does one close up to a stalled train in a station under CBTC?
Proceed in a normal operating mode as far as permitted by the MAL. With authorization from the Trainmaster, transition into Release mode and proceed at restricted speed to "close up" to the train in the station.
When a call-on (restricting signal aspect) is displayed at an interlocking signal in CBTC mainline territory, what ATC mode enable the train to pass it?
Release
If a train is in motion, only the following mode change is acceptable:
Release to MCS
What are the positions of the ATC Mode switch?
Release, MCS, MATC, ATO
What are the positions of the ATC mode switch?
Release, MCS, MATC, ATO
As a train engineer recovering from a failure at 9th street, the trainmaster directs you to proceed in release mode at 23rd street. When you arrive at 14th street, the TOD indicates "CBTC available". What should you do?
Remain in release mode as per the trainmasters instructions.
What should a train engineer do if he/she enters a cab and finds that the seal on the ATC Bypass switch is broken, or that the switch is not in the Normal (ATC) position?
Report it to the trainmaster/dispatcher immediately and await further instruction.
A green flag on the right side of the track indicates:
Resume normal speed
If you are adding to the rear of a trouble train with an electrical problem in the rear cars and are operating PA4 cars, you must
Retrieve the electrical portion at the add
When walking in the track area, employees must not walk or step on?
Running rails, train stops, transponders
As a train engineer operating in MATC mode, you arrive in a station where a CBTC train hold is in effect. After some delay, the trainmaster directs you via voice radio to depart, even though the train hold is in effect. What should you do?
Select MCS mode, touch the "hold" indication on the TOD, and depart from the station in MCS
What should the train engineer do If a Train Hold is in effect and the Trainmaster has directed him/her to proceed in spite it?
Select MCS mode, touch the Train Hold symbol on the TOD to cancel it, then depart the station is MCS
On a typical seven-car PA5 train with four "A" cars and three "C" cars, how many cars have air compressors?
Seven
When you lay up a train, you must:
Shut off lights and air conditioning, apply hand brakes and parking brakes
When climbing on or off a train, what must be avoided as a step?
Side incline/ drawhead, running rail, third rail protection board
How would your brakes react if the electric brake was cut out?
Slow applying and slow releasing
Two yellow flags tell you to:
Slow down to 15 mph
How does Release mode affect the operation of the train?
Speed is limited to 12 mph by the carborne ATC equipment, regardless of whether or not the train is localized
As a train engineer, you start a train from a station in MCS, and some distance later, you encounter two yellow flags but no "work zone ahead" indication is displayed on the CBTC TOD. What is your best course of action?
Stay in MCS mode, proceed as appropriate for the flagging arrangement, advise Control Center of the flags.
As a train engineer, you start a train from a station in MCS, and some distance later, you encounter two yellow flags no "work zone ahead" indication is displayed on the CBTC TOD. What is your best course of action?
Stay in MCS mode, proceed as appropriate for the flagging arrangement, advise Control Center of the flags.
A blue flag means:
Stop (track o/s), workers on or about the equipment, do not move or add to cut or charge. No train or rolling equipment may pass blue flag or lamp.
What do you do when you hear one long whistle from the tower?
Stop all movement
What if the meaning if you receive three buzzers from the conductor while the train is in motion?
Stop at next station or employee pick-up
How do you properly put a car into the shop building?
Stop at the door, push button associated with the blind automatic signal, locate overhead trolley, sound horn, put one car inside building, put overhead trolley on head car, proceed at pit speed.
What is the procedure for coupling where there is a cab at the point of the add (cab to cab)?
Stop ten feet away and verify couplers are aligned. Notch up to about 18 inches, add one point of power and make add. Charge train and check that air and electrical connections have been made. Make sure all angle cocks are opened and electrical portions are centered Extend end gates and hang safety chains.
A CBTC train is approaching a flashing green signal on a curve. The MAL display on the TOD indicates that the train must stop for a train ahead. No train is visible, however, the train engineer can not see very far beyond the signal because of the curve. What should the train engineer do?
Stop the train as required by the MAL and wait for the TOD to change to a less restrictive aspect.
What does a flashing red light over the letter "o" mean?
Stop, call for orders
What actions should you take when smoke is observed in the tunnel while operating a PA5 train?
Stop, call the trainmaster, shut OFF fresh air dampers
What should the engineer do if the TOD fails?
Switch to the backup CBTC-TOD screen and notify the Trainmaster.
What is the hand signal given to indicate "stop"?
Swung at a right angle to the track.
What is the maximum amount of cars that can be displayed on a PA5 TOD screen?
TEN
What should the engineer do if he/she encounters Rule 231 temporary speed restriction signs, but there is no Slow Speed Indication on the TOD and the engineer is operating in MATC mode?
Take manual control of the train and comply with Rule 231 and follow the posted speed sign. Notify the trainmaster.
What should a train engineer do when operating in MATC mode and there is no work zone indication on the TOD, but there are yellow flags/lamps in the field?
Take manual control of the train and comply with the flagging. Notify the Trainmaster.
What indications appear on the TOD when a train makes a proper station stop in MCS or MATC modes?
The "Train Berth" indication appears, along with the "Doors to Open" indication identifying which doors are enabled to open.
Which of the following conditions would result in the TOD indicating an 'unknown" operating mode?
The ATC car-borne equipment has completely failed
If the train engineer does not respect the order signal, what happens?
The ATC system has no effect on Call for Orders signals. The engineer must stop the train on their own.
If the train engineer does not stop to make an employee pick up, what happens?
The ATC system has no effect on employee pick-ups. The train engineer must stop the train on their own.
How is the Alerter used under ATC?
The Alerter must be used exactly the same way as pre-ATC train operations.
What MAL appears on the TOD when a train is approaching a failed signal?
The MAL will reflect the red signal.
What does it mean when the front end of a train is sieved?
The Zone Controller has determined that there is nothing between the front of the train and the next track circuit boundary.
What does the Daily Test verify?
The ability of the carborne ATC equipment to trigger an emergency brake application
What is a part of the localization process?
The car-borne ATC equipment determines the length of the train, the car-borne ATC's train length is equal to or greater than the length reported by the PA-5 rolling stock, and the train engineer confirms the length of the train
When an ATC-equipped train is following a non-ATC train, the ATC train's MAL will generally reflect?
The entering end of the track circuit in approach to the track circuit occupied by the non-ATC train
When a signal fails under CBTC, what effect does it have on ATC operations
The signal is forced to red.
For movement into CBTC Mainline territory, the mode change boundary occurs at what point?
The signal providing access to CBTC Mainline territory.
What is signal aspect?
The signal's appearance
An ATC train is rounding a curve. There are no trains ahead, no wayside signals in the area, and no temporary speed limits in effect. The limits of the train's maximum allowable speed are?
The speed limit from the car-borne map.
How does the train operate in Release mode?
The speed of the train is limited to 12 mph
What is the maximum allowable speed a train may operate in Bypass mode or if a non-ATC-equipped train?
The train can proceed at 40 mph.
The train was started in MATC and stopped between stations. What should the train engineer do next?
The train engineer can resume operation in MATC by pushing the ATC Start button when the TOD indications that the train can proceed.
Q: When the speed is in the yellow zone of the speed dial:
The train engineer must apply service braking to slow the train.
What happens if it is necessary to reopen the doors after they are closed and locked?
The train engineer must select the Cut-Out position of the ATC Door Mode switch, and then enable the doors on the correct side of the train with permission from Trainmaster
What should the train engineer do if a Stop and Stay cannot be released
The train engineer should notify the trainmaster and be governed by his/her instructions. In general, a mode switch to Release will be required
What happens if the ATC Door Mode switch is left in the Cut-Out position and you are in MCS/MATC mode?
The train engineer will have to manually enable the doors at station stops
How does a train engineer start train movement in MATC?
The train engineer will need to depress the ATC Start button after the doors are closed.
How can you determine your train has delocalized?
The train goes into emergency braking with loss of stationing numbers
What circumstances might require starting a train movement in release mode?
The train is stored on the same track and within 50 feet of another train in CBTC mainline territory
When the station dwell time reading is displayed in green reading ":07" it means:
The train should depart in 7 seconds
What will happen if MATC mode is selected on the ATC Mode switch while the train is in motion operating in MCS?
The train stops with an emergency brake application
A train is moving in MCS mode when it becomes delocalized. The train engineer can recognize that this has happened because:
The train stops with an emergency brake application, and the indication of stationing marker number disappears from the TOD.
What will occur if the train engineer does not touch the flashing mode indication in the allotted time?
The train will be halted with a service brake application.
What would happen if one attempted to enter Yard territory with the ATC mode switch in the MATC position?
The train would stop before leaving the mainline.
A MAL bar with green and yellow sections means that:
The training is being routed out of CBTC Mainline territory
What does it mean when the PA5 parking brake reset gauge is in the yellow zone?
There is enough air supply to activate the parking brakes or that the parking brakes are not applied in that car
When crossing over the third rail, what must be avoided?
Third rail side incline
As per rule 156 what is the proper whistle to use to acknowledge a hand, flag, or lamp signal to back up, before starting the backup movement?
Three Short
What is the proper buzzer to use when standing to back up?
Three short
How do all electrical and communications signals pass from one car to another?
Through electrical portions in the coupler
How do all electrical and communications signals pass from one car to another?
Through the electrical portions in the coupler
Why does the carborne ATC ask the train engineer for the train length?
To ensure that the train length is accurate, the carborne ATC equipment will ask the train engineer to reconfirm the train length.
Why is it necessary to wait for two minutes when recovering from a TOD failure accompanied by an emergency brake application:
To provide time during which the ATC car-borne equipment could restart.
What must every flat crew have with them prior to leaving for work rights?
Train Orders
What will happen if you try to charge the train in MATC mode?
Train will not charge
CBTC is called "communication-based" because?
Trains and wayside computers communicate with each other by means of a data radio link.
After receiving permission from the Trainmaster, what conditions must be satisfied before operating in Release mode?
Transition to Release mode once the train has come to a full stop.
What will not trigger an emergency brake application?
Traversing a failed track circuit in release mode
Which of the following will not trigger an emergency brake application?
Traversing a failed track circuit in release mode.
What function of the ATC car-borne equipment is verified in the Daily Test?
Triggering an emergency brake application
Assuming the engineer has indication, what procedure and corrective action must be taken if the PA4 train fails to take power?
Try using the motorman's bypass; reset motors, check control cut-out, move reverser key back and forth several times, try point of power in reverse: try to operate from the next cab in direction of travel, under flag using the bypass. IF that fails, split the train electronically by retrieving the electrical portion and see which section takes power. Move train from the live section using the Motorman's bypass. Good section must have equal or greater number of cars, if not, be prepared to couple to rescue train.
Where is Caisson 2 located?
Tunnels A/B and Tunnels E/F
What is the proper way to reset the emergency stop button on PA5 cars?
Turn it clockwise, pull it back out
Upon entering 33rd street in MATC you notice someone flagging your train to stop.
Turn mode selector switch to MCS and manually stop the train.
During a manual cut on PA5 cars, how many angle cocks will a switchman be required to close?
Two
As per rule 156 what is the proper whistle to release brakes, to proceed, and to acknowledge hand, flag, or lamp signals to stop or proceed.
Two Long
As per Rule 156 what is the proper whistle to use when approaching locations where workmen are on or about the tracks, at whistle markers, approaching stations where the train will not stop and exiting tunnel portals?
Two long, one short, one long
The coupler control lever located between the add of a PA-4 work car and flat must be in the______.
Uncoupled position
Under what conditions should a train engineer operate the ATC Bypass switch?
Under the direction of the trainmaster
What are the principal indications of a main reservoir rupture on a PA4 train?
Very slow loss of brake pipe and straight air pressures. If brake pipe pressure drops below 90 pounds, motor power will be lost, constant running of air compressor.
Which of the following is not a possible operating route in CBTC mainline territory?
Wayside
What information does a track indicator tell you?
What track you're lined up for
What is the proper way to perform a standing brake test?
When charged reduce straight air to 30 psi, and apply one point of power
How does speed regulation operate when the train is in release mode?
When speed exceeds 12 mph, service brakes are automatically applied until the train slows to 9MPH
For movement into Yard territory, the mode change boundary occurs at what point?
When the front of the train enters Yard territory.
When a train enters yard territory from CBTC mainline territory, when does the operating mode change?
When the front of the train enters yard territory
When will the Out of Service indication appear?
When the train arrives at the station where it is to be removed from service.
When will the Out of Service indication disappear?
When the train arrives at the station where it is to be removed from service.
When does an engineer move by absolute block?
When there is no automatic train stop, when train/vehicle does not shunt properly, or dead man protection in head car.
When can a CBTC train return to normal operation after accepting a "call-on"?
With permission from the Trainmaster, once the entire train is clear of the interlocking area and "CBTC Available" indication appears on the CBTC-TOD.
Which procedure is correct when making a cut between two PA5 cars?
With the train not charged, apply the parking brakes, insert vapor key into the coupler key switch and turn it to "ON", depress "ISOLATE"' depress "UNCOUPLE", charge train, buff and notch cars, when cars are uncoupled, turn coupler key switch to "OFF" and remove vapor key.
Does ATC impose any restrictions during train operations in Yard territory?
YES
If the train is operating in MATC mode, is a mode change necessary to traverse a work zone?
YES
What is Rule 102?
Yard Speed a speed in any operating mode except ATO/MATC that will permit stopping within one-half range of vision, but will not exceed 5 MPH on track with a derail which enter the shop building in Harrison yard, will not to exceed 8 MPH on the Harrison Yard Loop Track and in JSQ yards, and will not exceed 12 MPH on all other tracks in Harrison Yard and in South Street yard
When over-speed is detected; the color of the speed dial background turns to what color?
Yellow
Where are gamewell/emergency alarm boxes found?
Yellow or blue light locations in the tunnel
Are there any special conditions that go with operating ATC Bypass mode?
Yes. Initial movement in ATC Bypass must be with RESTRICTED Speed until the train reaches the next wayside signal.
During a break down recovery, what statement is true?
You must always have equal or greater number of good cars to move.
What will happen on an "OK" 7-car PA-5 where the drum switch is in the "Advance" position on the east end of train?
You will not get ADCL indication form the west end operating car.
Can MATC mode be used when stopping at an employee pick up?
no
Is MATC available when traversing a work zone?
no
What are the principle indications of a main reservoir rupture on a PA5 train and what is the corrective action?
rapid loss of MR pressure, constant running of air compressors, if MR pressure drops below 95 psi, the parking brake will apply.
What is the indication of a sign marked "W"?
sound horn in accordance with 156G
What happens if a CBTC train operating in MCS passes a station which it was designated to stop at.
the "Station Overrun" indication will appear on the TOD. CBTC will not apply braking if a station is overrun or skipped.
