4th period MidTerm

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

On a bandsaw, how high above the material should the blade guide be adjusted?

1/8 inch to 1/4 inch

Which of the following is true of a 15 inch drill press?

15 inches is the maximum depth of cut

What is the maximum speed of the scroll saw?

1600 strokes per minute

In which year was the Occupational Safety and Health Administration established?

1971

Which of the following is an important step after evaluation has taken place?

Accounting for all employees

What precautions should be taken when using a disk/belt sander?

All of the above

Which of the following are fire hazards commonly found in the shop?

All of the above

When using chisels, you should always _________.

All of the above. 0

Criteria for identifying sockets include which of the following?

All of the above. 1

Which of the following is a true statement?

Anticipation can be accomplished by knowing the history of the work

What is the recommended way to stop bleeding on a cut or laceration?

Apply direct pressure to the wound

What is the primary use of a miter saw?

Both A and C

Which of the following completely surrounds the nut or bolt head?

Box-end wrench

Which of the following is a tool used to mark the location of a hole which is going to be drilled?

Center punch

What is the unit of measurement for expressing the intensity of sound?

Decibel

A combination square ____________.

Determines is something is square or at a 90 or 45 degree angle

A feeler gauge _____________.

Determines the clearance between the parts

Which of the following is the first preference in the hierarchy control?

Elimination of Hazard

A hacksaw blade should be installed with the teeth pointed away from the handle.

False

Face shields provide excellent eye protection.

False

It is not necessary to tighten all three positions of the chuck on a drill press/

False

Screwdrivers are the most common and least misused hand tools?

False

The miter guage cannot be used to cut 45 degrees tapers.

False

Three thread types are standard, national fine and national coarse.

False

When applying direct pressure, you should check the wound every few seconds.

False

When treating a person who has ingested a chemical, you should always induce vomiting.

False

How much do ball peens weigh?

Four to 12 ounces

Most chisels are made of __________.

High carbon steel

What should you do if a penetrating eye injury occurs?

Immobilize uninjured eye

Where can you find handling and emergency information on chemicals used in the shop?

Material safety data sheets

Which of the following is a chemical hazard?

Oxygen deficiency

Which of the following is a health-related hazard?

Radiation

The thickness of the cut in a planer is determined by which of the following?

Raising or lowering the table

Which of the following is NOT a responsibility of a worker involving the use of PPE?

Replacing damaged PPE

The jointer is designed to do which of the following?

To clean the edge of a board

What is the main purpose of the band saw?

To cut circles or irregular shapes

Drill Press: A larger drill bit requires the drill press to operate at a slower speed.

True

If a twist drill is not tightened properly in the chuck it may slip and damage the drill shank.

True

If caustic chemicals are spilled on the skin, the skin should always be flushed with water.

True

Nut drivers are sized according to the socket size on the end.

True

On all saws, the splitter keeps the saw kerf open.

True

One type of torque wrench is the one-half inch click-type ratcheting wrench.

True

The scroll saw is one of the safest power tools in the shop.

True

Which of the following is NOT a true statement?

Under OSHA law, Employees must provide their own personal protective equipment

Which of the following is a tip for welding safety?

Wear dry gloves

How are screwdrivers sized?

Width of blade

What mark appears on the frame of industrial quality safety glasses?

Z87

A planer is designed to __________ a board.

decrease the thickness of


Ensembles d'études connexes

ACCT 3350 Final Exam (2021 Tax Year) ALL

View Set

Chapter 29: Management of Patients With Nonmalignant Hematologic Disorders

View Set

Pediatric success, Saunders & Davis test 2 questions

View Set

Politics and Public Policy in China

View Set

Density Practice Problems! + Rubber Duck --Just practice problems, NOT a study guide!

View Set

Weekly Challenge 3: Define User Problems

View Set

IBDP Computer Science: Computer Networks

View Set

SOC 100 Aging and the Elderly Chap 13

View Set

Chapter 1: Introduction to Nursing

View Set

Digital Video Ads, VAST, and VPAID

View Set