Avengers End Game

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

Which wildcard mask would be used to advertise the 192.168.5.96/27 network as a part of OSPF configuration?

0.0.0.31

Analyze the routes in the routing table to determine the metric. Match each value to its corresponding filed in the table.

1) 10.4.0.0/16 Ans : 0 2) 172.16.2.0/24 Ans : 0 3) 172.16.3.0/24 Ans : 1 4)192.168.110.0/24 Ans : 65 5)192.168.120.0/24 Ans : 2172416

Analyze the route in the routing table to determine the AD. Match each value to its corresponding filed in the table

1) 10.4.0.0/16 Ans : 1 2) 172.16.2.0/24 Ans : 0 3) 172.16.3.0/24 Ans : 90 4)192.168.110.0/24 Ans : 110 5)192.168.120.0/24 Ans : 120

Analyze The Routes In The Routing Table To Determine The Route Source. Match Each Value To Its Corresponding Filed In The Table

1) 10.4.0.0/16 Ans : static 2) 172.16.2.0/24 Ans : connected 3) 172.16.3.0/24 Ans : EIGRP 4)192.168.110.0/24 Ans : OSPF 5)192.168.120.0/24 Ans : RIP

Write The Name Of The Protocol (OSPF,RIP Or EIGRP) Which Best Matches The Metric Described. Please Write Only One Protocol In Per Metric

1. Metric Based on hop counts : RIP 2: Uses cost(cumulative link bandwidth) as its metric: OSPF 3: Matric can be based additionaly on load (amount of link traffic and reliability probability of link failure): EIGRP 4: Metric is based on delay and bandwidth: EIGRP

A switch is configured with all ports assigned to vlan 2 with full duplex FastEthernet to segment existing departmental traffic. What is the effect of adding switch ports to a new VLAN on the switch?

An additional broadcast domain will be created.

which layer in the OSI reference model is responsible for determining the availability of the receiving program and checking to see if enough resources exist for that

Application layer

Which of the following routing protocols is NOT an interior gateway protocol (IGP)?

BGP (border gateway protocol)

Why would a network administrator implement VLANs?

Broadcast control

what type of route allows a router to forward packets even though its routing table contains no specific route to the destination network?

Default route

Each routing type description in the table can be classified as Static Routing or Dynamic Routing. Mark the appropriate classification next to each routing type descriptions.

Dynamic routing- suitable for multiple router topologies Dynamic routing -adapts to topology changes Static routing - easy to implement small network Dynamic routing - requires more CPU, RAM static routing- route to destination is always same

An administrator has connected devices to a switch and, for security reasons, wants the dynamically learned MAC addresses from the address table added to the running configuration. What must be done to accomplish this?

Enable port security and use the keyword sticky

Where should we place extended access-lists?

Extended access lists should be placed as close to the source as possible.

A router has two Fast Ethernet interfaces and needs to connect to four VLANs in the local network. How can you accomplish this task, using the fewest physical interfaces and without decreasing network performance?

Implement a router-on-a-stick configuration

A Cisco switch currently allows traffic tagged with VLANs 10 and 20 across trunk port Fa0/5. What is the effect of issuing a switchport trunk allowed vlan 30 command Fa0/5?

It allows only VLAN 30 on Fa0/5.

What is the function of the command switchport trunk native vlan 999 on a Cisco Catalyst switch?

It designates VLAN 999 for untagged traffic.

Which statement about the OSPF Router ID is true?

It identifies the source of a type 1 LSA. OR The router automatically chooses the IP address of a loopback as the OSPF Router ID

Which statement describes the process ID that is used to run OSPF on a router?

It is locally significant and is used to identify an instance of the OSPF database.

What is the benefit of using a single OSPF area network design?

It reduces the types of LSAs that are generated. It removes the need for virtual links

In the configuration of NAT, what does the keyword overload signify?

Multiple internal hosts will use one IP address to access external network resources

Match the memory functions to the memory types. You can easily write the name of each Memory function in front of the corresponding memory type.

NVRAM - start-up configuration Flash - IOS and system files ROM - Diagnosis and boot function RAM - running configuration

To what does the 128 refer to in the router output above?

OSPF cost

Which of the following is NOT a valid action of port-security?

Reset

Host 1 is trying to communicate with Host 2. The e0 interface on Router C is down. Which of the following are true?

Router C will use ICMP to inform Host 1 that Host 2 cannot be reached. Router C will send a Destination Unreachable message type.

What type of packets would match th access control list statement that is shown below? " access-list 110 permit tcp 172.16.0.0 0.0.0.255 any eq 22 "

SSH traffic from the 172.16.0.0 network to any destination network

If we have multiple IOS versions on our router, how can we view which ones are available?

Show flash

Refer to the exhibit. Switch-1 needs to send data to a host with a MAC address of 00b0.d056.efa4. What will Switch-1 do with this data?

Switch-1 will flood the data out all of its ports except the port from which the data originated.

Refer to the exhibit. the ports that are shown are the only active ports on the switch. the mac address table is shown in its entirety. the ethernet frame that is shown arrives at the switch. which operation will the switch perform when it receives this frame?

The MAC address of 0000.00aa.aaaa will be added to the MAC address table. The frame will be forwarded out fa0/1, fa0/2, and fa0/3.

VLAN 3 is not yet configured on your switch. What happens if you set the switchport access vlan 3 command in interface configuration mode?

The command is accepted and the respective VLAN is added to vlan.dat

Refer to the Exhibit. All switch ports are assigned to the correct VLANs, but none of the hosts connected to SwitchA can communicate with hosts in the same VLAN connected to SwitchB. Based on the output shown, what is the most likely problem?

The link between the switches needs to be configured as a trunk

A network administrator is trying to add a new router into an established OSPF network. The networks attached to the new router do not appear in the routing tables of the other OSPF routers. Given the information in the partial configuration shown below, what configuration error is causing this problem? Router(config)# router ospf 1 Router(config-router)# network 10.0.0.0 255.0.0.0 area 0

The network wildcard mask is configured improperly.

How many broadcast and collision domains are shown in the network graphic?

There are 2 broadcast domains There are 7 collision domains 2,7

Which statement about VLAN operation on Cisco Catalyst switches is true?

Unknown unicast frames are retransmitted only to the ports that belong to the same VLAN

Which interface is the default location that would contain the IP address used to manage a 24-port Ethernet switch?

VLAN 1

What route would have the lowest administrative distance?

a directly connected network

In a switched environment what does the IEEE 802.1q standard do?

a method of VLAN trunking It is used to "tag" frames in order to ensure that they are sent to the right VLAN.

Which parameter would you tune to affect the selection of a static route as a backup. When a dynamic protocol is also being used?

administrative distance

What is the purpose of assigning an IP address to a switch?

allows remote management of the switch

A network administrator is verifying the configuration of a newly installed host by establishing an FTP connection to a remote server. What is the highest layer of the protocol stack that the network administrator is using for this operation?

application

What information does a router running a link-state protocol use to build and maintain its topological database?

hello packets LSAs from other routers

What OSPF command, when configured, will include all interfaces into area 0?

network 0.0.0.0 255.255.255.255 area 0

Which of the following statement is true?

not "Switches control broadcast domain"

What command do we use to find out how long our router has been online?

show version

A router has learned three possible routes that could be used to reach a destination network. One route is from EIGRP and has a composite metric of 20514560. Another route is from OSPF with a metric of 782. The last is from RIPv2 and has a metric of 4. Which route or routes will the router install in the routing table?

the EIGRP route

Refer to the exhibit below. which two destination addresses will be used by Host A to send data to Host C?

the IP address of Host C the MAC address of the router's E0 interface

What is the function of OSPF hello packets?

to discover neighbors and build adjacencies between them

A network administrator configures a router by the command ip route 0.0.0.0 0.0.0.0 209.165.200.226. What is the purpose of this command?

to provide a route to forward packets for which there is no route in the routing table

What does VLSM allow a network administrator to do?

utilize multiple different subnet masks in the same IP address space


Ensembles d'études connexes

Astro 7N Copper Quizzes (Units 1 and 2)

View Set

NUR1211- CH 51 Assessment and Management of Patients with Diabetes

View Set

Managerial Accounting RQ Chapter 13 #1

View Set

International Business Chapter 3

View Set

CyberSecurity last 1/4 Semester Exam Study Guide

View Set