Champions School Home Inspection

A good concrete garage floor slab is usually

at least 3 inches thick and has 5 inches of gravel beneath it.

Handrails are not required on ramps having a maximum slope of ________. a.1:8 b.1:12 c.1:15 d.1: 18

b 1:12

Unless a minimum tread depth of _____ is provided, a minimum ¾ inch nosing is required at the leading edge of all treads. a.9 ½ inches b.10 inches c.11 inches d.12 inches

c. 11 inches

Stucco is made up of

cement, aggregate and water

If a bedroom has burglar bars, what are they required to have for proper egress? a.No windows 3' to property line b.Window wells minimum 95 square feet and 36" minimum dimension c.5.7 square feet minimum clear opening d.Security bars must have approved release hardware

d.Security bars must have approved release hardware

Three general types of report formats.

1.Checklist 2.Narrative 3.Combination

Six common problems with caulking, trim and flashings:

1.Missing flashings; 2.Ineffective or incomplete flashings; 3.Loose; 4.Rust; 5.Rot; 6.Caulking missing or ineffective

Two time options for report delivery.

1.On site reports 2.Reports sent after the inspection

Three main functions of exterior cladding:

1.Protect the structure from water; 2.Provide reasonable security; 3.Enhance the appearance of the home

Three mechanisms by which water may get into wall systems from the building exterior

1.Rain driven by wind; 2.Rain running down the wall (gravity); 3.Water wicking into the wall (capillary action)

Ten common components of the body of the report

1.Scope/contract 2.Descriptions 3.Conditions or evaluations 4.Causes of conditions 5.Implications of conditions 6.Recommended actions 7.Limitations 8.Life expectancy 9.Priorities 10.Ballpark costs

Four reasons why written reports are needed.

1.The Standards require it 2.To help the client 3.To control your liability 4.Marketing tool

The typical life expectancy of an asphalt shingle roof is: An asphalt shingle roof typically lasts

15-25 years

The openings between railing spindles should not be greater than

4 3/8

A single handrail is adequate for stairs up to

44 inches wide

Which statement is true? (a) Increasing the insulation makes the attic warmer. (b) If the attic is cold, then warm, moist air leaking into the attic from the house will condense more quickly. (c) If you increase the insulation level in a roof, you should decrease the ventilation. (d) The insulation and ventilation cannot affect the structure of a roof.

?

The following roofs are most prone to ice dams:

A low slope roof with a wide soffit.

A minor leak can be more of a problem than a major one because:

A minor roof leak may cause considerable damage before it is noticed

What is efflorescence and what causes it:

Efflorescence is a whitish powdery salt deposit that is associated with water moving through masonry. Water dissolves the salts from masonry or mortar and deposits them on the surface as crystals when evaporating

Bad grading will always cause wet basements. T/F ?

False

The proper way to flash a ledgerboard installed over siding:

Flashing extends from under the siding, over the top of the ledgerboard, and down

Why you shouldn't align a beam with a gutter to check for sag:

Gutters slope so they always look off level

The sides of a roof that will wear faster in climates where ultraviolet light is the main aging factor are

South and west

Installing joists with hangers is considered superior to toe-nailing them to beams because:

There is more protection against uplift and twisting with a joist hanger

Sloped roofs are not waterproof because:

They are designed to shed water like a series of umbrel-las. They are not designed to control standing water.

There should be no supply or return registers from heating/cooling ductwork in a garage because:

To prevent fumes from entering the house.

Deck boards often rot first

Where the joists penetrate the wall

A service conductors overhead clearance must be: a.10' max. above walking surface b.12' max. above residential property and driveways c.18' above public streets, alleys or parking areas d.All of the above

a.10' max. above walking surface

Sloped glazing is glass or other glazing material installed at a minimum slope of _________. a.15 degrees from the vertical b.30 degrees from the vertical c.15 degrees from the horizontal d.30 degrees from the horizontal

a.15 degrees from the vertical

What is the minimum/maximum length of a Disposal Cord? a.18 inches minimum, 36 inches maximum b.12 inches minimum, 36 inches maximum c.24 inches minimum, 36 inches maximum d.36 inches minimum, 48 inches maximum

a.18 inches minimum, 36 inches maximum

A forced air furnace room passageway should be a minimum of ____________ inches wide (according to the IRC). a.24" b.30" c.15" d.20"

a.24"

It's a good idea to have a __-inch step up into the house from the porch, deck, or patio floor. Why is this? a.6 inch. This reduces the chance of snow or water getting into the structure under the bottom of the door. b.8 inch. This reduces the chance of snow or water getting into the structure under the bottom of the door. c.9 inch. This reduces the chance of snow or water getting into the structure under the bottom of the door. d.10 inch. This reduces the chance of snow or water getting into the structure under the bottom of the door

a.6 inch. This reduces the chance of snow or water getting into the structure under the bottom of the door

What are 2 examples of anything that restricts the drainage of water in a vulnerable area: a.Butterfly roofs, Chimneys in valleys. b.Narrow chimneys near the lower edge of the roof. c.Valleys, Ridge. d.Skylights, drains from upper roofs with a downspout extension discharging water into a gutter installed on the lower roof

a.Butterfly roofs, Chimneys in valleys.

Drilled holes in floor joist are allowed? a.In the outer 1/3, midway from top to bottom b.In the middle 1/3, any where c.In the middle 1/3/ end to end d.In the middle 1/3, only near the bottom

a.In the outer 1/3, midway from top to bottom

What is the purpose of a Pitch Pocket? a.Is used to flash irregularly shaped roof penetrations Is used to flash regular shaped roof penetrations b.Is used to flash plumbing roof penetrations c.Is used to establish a distinct point of interest on a roof

a.Is used to flash irregularly shaped roof penetrations Is used to flash regular shaped roof penetrations

What is two of the functions of exterior doors? a.Means of entry and exit and security b.Privacy and dedication. c.Weathertight and waterproofing. d.Waterproofing or fireproofing if they connect to a garage.

a.Means of entry and exit and security

A window is installed above a tub in a bathroom. The inspector inspects the window to verify it is identified as tempered glass as required by hazardous locations in the code. There this no acid etching to indicate the window is tempered. He /she measures from the top of the tub to the bottom sash of the window and the measurement is 63 inches. Is this a deficiency? a.No, it is not in a hazardous location. b.Yes, it is in a hazardous location. c.Yes, it is over 5 feet from the top edge of the tub. d.None of the above

a.No, it is not in a hazardous location

15.Brick Veneer has a 1/8 of an inch crack in the mortar at both sides of a window header the most likely cause of this is? a.Rusted lintel b.Building racking c.Loose mortar d.Wall tie

a.Rusted lintel

You see "double-trapping" at a kitchen sink. Is this a defect? Why or why not? a.This is a defect. If we have double trapping, the velocity coming into the second trap will be reduced and solids are more likely to collect and clog the second trap. b.This is not a defect. If we have double trapping, the velocity coming into the second trap will be reduced and solids are more likely to collect and clog the second trap. c.Could be a defect. If we have single trapping, the velocity coming into the second trap will be reduced and solids are more likely to collect and clog the second trap. d.I don't think it is a defect. If we have double trapping, the velocity coming into the second trap will be reduced and water is not likely to collect and clog the second trap

a.This is a defect. If we have double trapping, the velocity coming into the second trap will be reduced and solids are more likely to collect and clog the second trap.

If you fail to find the discharge point of the sump pump at an inspection, what should you tell your client? a.You should tell your client that you could not find the discharge point and that further investigation is needed. b.You should tell your client nothing and they should already know this. c.You should tell the client, that they should expect problems. d.You should tell your client that you found the discharge point and further investigation is needed.

a.You should tell your client that you could not find the discharge point and that further investigation is needed.

Foundations often serve as the _________ floor, as well as the support for the house________. a.building, loads. b.framed, floors. c.building, walls. d.load, floors.

a.building, loads

A dishwasher may NOT drain properly because the ___________. a.timer may be faulty. b.door and the lock may be defective. c.heating element may be burned out. d.clock may be faulty

a.timer may be faulty.

When a framing member is notched, the hole shall not be closer than ____ inches to the notch. a.1" b.2 " c.2 1/2" d.3"

b. 2"

A wood stove should have a pad under it that prevents sparks or embers from igniting a combustible floor. How far should this pad extend out in front of the stove? a.12 inches b.16 inches c.20 inches d.24 inches

b.16 inches

Unless located a minimum of 60 inches above the floor or walking surface, glazing within a ______ arc of a door shall be considered to be installed in a hazardous location. a.12 inch b.24 inch c.36 inch d.60 inch

b.24 inch

Which of the following is NOT a true statement concerning code requirements for areas which require the use of pressure preservative treated or decay-resistant lumber? a.Bottom of wood joists must be closer than 18 inches to exposed ground. b.Bottom of wood girder beams must be closer than 14 inches to exposed ground. c.Bottom of wood siding must be 6 inches above ground. d.Sills and sleepers must be on a concrete slab which is in direct contact with ground.

b.Bottom of wood girder beams must be closer than 14 inches to exposed ground.

What is the function of a guard? a.Guards keep you from falling off a hallway or over the edge of a stairway or balcony. b.Guards keep you from falling off a hallway or over the edge of a landing or balcony. c.Guards keep you from falling on a hallway or over the edge of a landing or balcony. d.Guards keep you from falling off a hallway or over the wall of a landing or balcony

b.Guards keep you from falling off a hallway or over the edge of a landing or balcony.

it is has not rained in a long time, and there is no ponding at the time of the inspection, what are other clue that might lead you to believe that the roof has experienced some ponding? a.Look for algae and vegetation on the roof surface. b.Look for dirt, algae and vegetation on the roof surface. c.Look for dirt, and vegetation on the roof surface. d.Look for dirt, and algae on the roof surface

b.Look for dirt, algae and vegetation on the roof surface.

For proper installation of Exterior Insulation Finish Systems (EIFS), what must be done? a.Must follow local health codes b.Must follow manufacturer instructions c.Must follow builders instructions d.Must follow drywall installer's instructions

b.Must follow manufacturer instructions

A piece of glazing is 20 inches from an entry door and runs the full height of the door. Which one of the following types of glass is acceptable in this location? a.Annealed b.Safety glazing tempered and tested c.Laminated d.Heat-strengthened

b.Safety glazing tempered and tested

Why is it critical to document how the crawlspace was inspected? a.Your client has to understand the limitations of your inspection. Crawl spaces can be troublesome. If you couldn't get a good look, your client should understand that there is no risk of unforeseen problems. b.Your client has to understand the limitations of your inspection. Crawl spaces can be troublesome. If you couldn't get a good look, your client should understand that there is a greater risk of unforeseen problems. c.Your client has to understand the routine of your inspection. Crawl spaces can be troublesome. If you couldn't get a good look, your client should understand that there is a greater risk of unforeseen problems. d.Your client has to understand the limitations of the seller. Crawl spaces can be troublesome. If you couldn't get a good look, your client should understand that there is a greater risk of unforeseen problems

b.Your client has to understand the limitations of your inspection. Crawl spaces can be troublesome. If you couldn't get a good look, your client should understand that there is a greater risk of unforeseen problems.

There are two layers of shingles on the roof, with the most recent installation less than two years old. At the chimney, the original steel flashings are rusted. The shingles are sealed to the older metal with asphalt cement. The roofer should have - a.used caulking instead of asphalt cement. b.installed new flashings. c.stripped off the old shingles first. d.replaced only the flashings that are rusted through.

b.installed new flashings.

Which one of the following areas in a dwelling unit does not specifically require the installation of a smoke alarm? a.Basement b.Kitchen c.Habitable attic d.Sleeping room

b.kitchen

A properly installed food waste disposer that makes no sound when activated can sometimes be activated by a.resetting the kitchen GFCI receptacle. b.pressing the thermal cutoff button. c.turning the motor with a hex wrench. d.running cold water into the disposer

b.pressing the thermal cutoff button.

Where located less than 5 feet above the walking surface, glazing a wall enclosing an indoor hot tub shall be considered to be installed in a hazardous location unless the glazing is a minimum of ______ horizontally from the water's edge. a.3 feet b.4 feet c.5 feet d.10 feet

c. 5 feet

What is the minimum required separation for a wall between dwelling units in a non-sprinklered two family dwelling? a.½ inch gypsum board on each side b.30 minute fire resistance rated c.1 hour fire resistance rated d.2 hour fire resistance rated

c.1 hour fire resistance rated

In an attic assuming there is a proper balance of vents installed what is the maximum number of square feet of attic floor to be vented? a.1 square foot of net free vent space for 150 square feet of attic floor b.1 square foot of net free vent space for 200 square feet of attic floor c.1 square foot of net free vent space for 300 square feet of attic floor d.1 square foot of net free vent space for 250 square feet of attic floor

c.1 square foot of net free vent space for 300 square feet of attic floor

Pull-down stairs should be installed according to manufacturer's instructions. The instructions often specify either 16d nails or _____ inch diameter lag screws for attaching the stair frame to the ceiling framing. a.1/2 b.2 c.1/4 d.1/8

c.1/4

Any duct penetrating the wall or ceiling separating the dwelling from the garage shall be constructed of a minimum _______sheet steel or other approved material. a.No. 22 gauge b.No. 24 gauge c.No. 26 gauge d.No. 28 gauge

c.26 gauge

What is the minimum slab thickness of a fireplace hearth slab? a.16" b.6" c.4" d.8

c.4"

If the garage door isn't closing all the way and is stopping approximately 2 inches from the bottom, what does this signify? a.Adjustment of the opening limit b.Adjustment of the limit c.Adjustment of the closing limit d.Adjustment of the reversing limit

c.Adjustment of the closing limit

Crawlspaces may be built very similar to _________? a.Monolithic slab. b.Floating slab. c.Basements d.Split level homes

c.Basements

Common and dangerous cracks in the hearth of a wood-burning fireplace are often found: ______. a.At the back of the hearth. b.At the side of the hearth. c.Between the hearth and hearth extension. d.At the front of the hearth extension.

c.Between the hearth and hearth extension.

Ceiling joists are often not continuous from one side of the building to the other. In this case, they spliced over a central bearing wall. Why do they have to be securely tied together? a.Ceiling joists help prevent collar ties and the tops of walls from being pushed outward by live loads on the roof. They must be continuous to resist these forces. b.Ceiling joists are often in tension, running from the bottom of one rafter to another. They must be continuous to resist these forces. c.Ceiling joists help prevent rafters and the tops of walls from being pushed outward by live loads on the roof. Ceiling joists are often in tension, running from the bottom of one rafter to another. They must be continuous to resist these forces. d.Ceiling joists help prevent purlins and the tops of walls from being pushed outward by live loads on the roof. Ceiling joists are often in tension, running from the bottom of one rafter to another. They must be continuous to resist these forces

c.Ceiling joists help prevent rafters and the tops of walls from being pushed outward by live loads on the roof. Ceiling joists are often in tension, running from the bottom of one rafter to another. They must be continuous to resist these forces.

What are two examples of how you might differentiate between a roof leak and a condensation problem in an attic. a.Roof leaks tend to be more uniform and wide spread than leakage. Leaks tend to run down sloped roof surfaces following gravity. b.Condensation tends to be more uniform and wide spread than leakage. Condensation is uniform laterally across the roof. c.Condensation tends to be more uniform and wide spread than leakage. Condensa-tion is uniform laterally across the roof. Leaks tend to run down sloped roof surfaces following gravity. d.Condensation tends to be more wide spread than leakage. Condensation is uniform laterally across the roof. Leaks tend to run up sloped roof surfaces following gravity.

c.Condensation tends to be more uniform and wide spread than leakage. Condensa-tion is uniform laterally across the roof. Leaks tend to run down sloped roof surfaces following gravity.

What must the garage entry door to the home be made of for fire protection? a.Door (interior stair only) - Maximum open at but not swing over top step b.Door must be 1 3/8" hollow core c.Door to house rated 20 minute or 1 3/8" solid core d.Door to house rated 15 minute or 1" solid core

c.Door to house rated 20 minute or 1 3/8" solid core

What are some of the basic components of a masonry chimney? a.Foundation, Chimney cap, Chimney walls. b.Connector, walls. c.Footing and foundation, Chimney cap, Chimney walls. d.Liner, Chimney cap

c.Footing and foundation, Chimney cap, Chimney walls.

Which of the following is not a true statement about vented decorative appliances? a.Vented decorative appliances shall conform to ANSI Z21.50. b.Vented decorative appliances shall be installed in accordance with the manufacturer's installation instructions. c.Gas logs shall be equipped with pilot ignition and a labeled safety shutoff valve. d.Vented decorative appliances shall be provided with combustion and circulating air

c.Gas logs shall be equipped with pilot ignition and a labeled safety shutoff valve.

Briefly describe a party wall. Include its location, function and possible materials. a.Party walls are located between dwelling units, and act as a sound and fire separation. Common materials are wood block and wood frame with drywall. b.Party walls are located between attached dwelling units, and act as a sound and fire separation. Common materials are masonry block and wood frame. c.Party walls are located between attached dwelling units, and act as a sound and fire separation. Common materials are masonry block and wood frame with drywall. d.Party walls are located between attached dwelling units, and act as a sound. Common materials are masonry block and wood frame with drywall

c.Party walls are located between attached dwelling units, and act as a sound and fire separation. Common materials are masonry block and wood frame with drywall.

What are the 3 main functions of roofs? a.Protect the building from rain, snow, wind, hail and fire, Support some of the mechanical equipment for the house. b.Not protect the building from rain, snow, wind, hail and fire, Support some of the mechanical equipment for the house, Make an architectural statement. c.Protect the building from rain, snow, wind, hail and fire, Support some of the mechan-ical equipment for the house, Make an architectural statement. d.Protect the building from rain, snow, wind, hail and fire, Does not support some of the mechanical equipment for the house, Make an architectural statement

c.Protect the building from rain, snow, wind, hail and fire, Support some of the mechan-ical equipment for the house, Make an architectural statement

Starting at the supply plenum, list the components of the duct system the air travels through to deliver heat to the room, and to re-enter the furnace at the return site. a.The air travels across the room from supply register to return grille, through the return ducts to the return plenum, where it re-enters the furnace to be reheated. b.The heated air is pushed through the supply plenum, along the supply ducts, out the registers into the room. c.The heated air is pushed through the supply plenum, along the supply ducts, out the registers into the room. The air travels across the room from supply register to return grille, through the return ducts to the return plenum, where it re-enters the furnace to be reheated. d.The heated air is pulled through the supply plenum. The air travels across the room from the return register to return grille, through the return ducts to the return plenum, where it re-enters the furnace to be reheated

c.The heated air is pushed through the supply plenum, along the supply ducts, out the registers into the room. The air travels across the room from supply register to return grille, through the return ducts to the return plenum, where it re-enters the furnace to be reheated.

For ranges, ovens and cooktops, an inspector should look for __________ __________ in the burner jets and see that gas tunnels are securely fastened and properly routed from pilots to burners. a.decrease grease b.gas regulator c.excessive grease d.grease grease

c.excessive grease

A receptacle installed with a cover labeled suitable for wet locations, dual equipment grounding conductors, with GFCI protection installed at the point of installation may be installed in a bathtub or shower space. a.the above statement would be true, if the GFCI protection had been installed at the circuit point of origin. b.the above statement would be true, if approved by a professional engineer. c.the above statement is considered a false statement by IRC code/ and manufactory specs. d.the above statement would be approved if the circuit was installed by a licensed master electrician

c.the above statement is considered a false statement by IRC code/ and manufactory specs

Which is the most acceptable fastener for connecting a deck ledger to a rim joist? a.⅝ inch diameter stainless steel carriage bolt. b.½ inch diameter electroplated galvanized steel wood screw. c.½ inch diameter hot-dipped galvanized steel machine bolt. d.⅝ inch diameter brass machine screw.

c.½ inch diameter hot-dipped galvanized steel machine bolt

Where a window well is required in conjunction with an escape and rescue opening, the window well shall have a minimum net clear area of ______ square feet with a minimum horizontal dimension of ________. a.5.7, 20 inches b.5.7, 24 inches c.9.0, 30 inches d.9.0, 36 inches

d. 9.0, 36 inches

Openings located less than 3 feet from an interior property line shall be protected with what minimum fire protection rating? a.0 hours; no protection rating is required b.20 minutes c.45 minutes d.Openings not permitted

d. openings not permitted

Based on where the home is located on the property, an exterior wall having a fire separation distance less than 3 feet, penetrations protected with an approved penetration fire stop system shall have a minimum fire resistance rating of ____________. a.20 minutes b.30 minutes c.45 minutes d.1 hour

d.1 hour

The opening size of an operable window should be limited to less than _____ inches if, the bottom edge of the window opening is less than 24 inches of the interior of the floor, and the bottom edge of the window opening is more than 6 feet above exterior grade. a.20 b.8 c.6 d.4

d.4

A garage located beneath a habitable room shall be separated from the room by a minimum ____gypsum board. a.1/2 inch b.1/2 inch Type X c.5/8 inch d.5/8 inch Type X

d.5/8 inch Type X

Gas connectors serving range tops must be no more than _______ feet in length epoxy coated or stainless steel, served by an accessible shut off valve within ____ feet of the appliance and leak free. a.1, 6 b.3, 3 c.3, 6 d.6, 6

d.6, 6

In masonry chimneys, adjacent flues are usually separated by: _______. a.A clay tile liner. b.An air space. c.A stainless-steel divider. d.A wythe of brick.

d.A wythe of brick

A hydro massage bathtub circuit: a.Must have disconnect within sight of motor b.Must be GFCI protected c.Disconnect may be a cord and plug d.All of the above

d.All of the above

What proper attic ventilation is required? a.Vent each enclosed attic and rafter bay b.1/8" to mesh screen over openings c.Net area of openings - Minimum 1/50th of vented area or 1/300th if 50-80% of venting is near the top or vapor barrier d.All of the above

d.All of the above

What should be done with plates and sills? a.Bottom of sill 8" to earth b.Sill material treated c.Sill material naturally or decay resistant d.All of the above

d.All of the above

Interconnected smoke alarms are typically connected using a wire, but newer wireless tech-nology is available that allows smoke alarms to be interconnected without using wires. If you are inspecting a home and observed that they have both types of smoke alarms installed, what would you report to your client? a.That this type of installation is a violation of current code. b.That this type of installation is a violation of current standards as they all should be the same. c.This a deficiency because you are not allowed per the Standards of Practice to have this type of installation. d.Inspected, and that you did observe smoke alarms in all the required location. Note that you might want to check the expiration date for the smoke alarms installed as most of them have a 10-year expiration date.

d.Inspected, and that you did observe smoke alarms in all the required location. Note that you might want to check the expiration date for the smoke alarms installed as most of them have a 10-year expiration date.

What would you tell a client about a retaining wall that is leaning over but not broken, cracked, or damaged? a.It is impossible to tell from a single visit if the wall is in danger of collapse. b.It is easy to tell as an inspector, from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist. c.It is impossible to tell from a single visit if the wall is in danger of collapse. Straight walls with no cracks or buckling should be further investigated by a specialist. d.It is impossible to tell from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist

d.It is impossible to tell from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist

What would you tell a client about a retaining wall that is leaning over but not broken, cracked, or damaged? a.It is impossible to tell from a single visit if the wall is in danger of collapse. b.It is easy to tell as an inspector, from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist. c.It is impossible to tell from a single visit if the wall is in danger of collapse. Straight walls with no cracks or buckling should be further investigated by a specialist. d.It is impossible to tell from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist.

d.It is impossible to tell from a single visit if the wall is in danger of collapse. Leaning walls with no cracks or buckling should be further investigated by a specialist.

You are inspecting a home with a heat pump installed and suspect that the heat pump is over-sized what is the implication of an oversized heat pump during the summer months. a.It would heat the house up too fast without dehumidifying the air, resulting in a cool, damp environment. b.It would cool the house down too fast without humidifying the air. c.It would cool the house down too fast without dehumidifying the air, resulting in a warm, damp environment. d.It would cool the house down too fast without dehumidifying the air, resulting in a cool, damp environment.

d.It would cool the house down too fast without dehumidifying the air, resulting in a cool, damp environment

What is the difference between a live load and a dead load? Give examples. a.Dead loads, such as people, wind, and snow, vary. Live loads, such as the building materials, are relatively fixed. b.Live loads, such as people, wind, and snow, vary. Live loads, such as the building materials, are relatively fixed. c.Live loads, such as buildings, wind, and snow, vary. Dead loads, such as the people materials, are relatively fixed. d.Live loads, such as people, wind, and snow, vary. Dead loads, such as the building materials, are relatively fixed.

d.Live loads, such as people, wind, and snow, vary. Dead loads, such as the building materials, are relatively fixed

What's the difference between a Spanish tile and Mission tile? a.Mission tiles come in one piece - pan. Spanish tiles come in one piece and have interlocking sides. b.Mission tiles come in four pieces - pans and covers. Spanish tiles come in one piece and have interlocking sides. c.Mission tiles come in six pieces - pans and covers. Spanish tiles come in one piece and have interlocking sides. d.Mission tiles come in two pieces - pans and covers. Spanish tiles come in one piece and have interlocking sides.

d.Mission tiles come in two pieces - pans and covers. Spanish tiles come in one piece and have interlocking sides

In what two ways might installing joists with hangers be considered superior to toe-nailing them to beams? a.There is no need for protection against uplift and twisting with a joist hanger. b.There is more protection against uplift and bowing with a joist hanger. c.There is more protection against down lift and twisting with a joist hanger. d.There is more protection against uplift and twisting with a joist hanger.

d.There is more protection against uplift and twisting with a joist hanger

From the point where the ground and the neutral wires connect, there are two paths to ground. What are they? a.Through the neutral wire or through the grounding electrode conductor to water pipes or ground. b.Through the neutral wire or through the grounding electrode conductor to water or ground rods .c.Through the hot wire or through the grounding electrode conductor to water pipes or ground rods. d.Through the neutral wire or through the grounding electrode conductor to water pipes or ground rods.

d.Through the neutral wire or through the grounding electrode conductor to water pipes or ground rods.

Electric/gas bathroom heaters safe installation will include consideration of clearance from _______ , and general conditions of controls, housings, burners, and other components. a.non-combustibles b.compostable c.composite d.combustibles

d.combustibles

Guardrails are typically required on porches, decks, or balconies

more than 24 or 30 inches above grade.

Two good repair methods for slate are:

slate hooks and making babies