CSM 2313 Final

What is visible in a building section?

-roof slope - elevations -construction materials -interior ceiling heights

What is the dimensional size of a 2x4 wall? *

1 1/2" x 3 1/2"

What scale is the site plan of the residential project? *

1" = 20'-0"

Kitchen Upper Cabinet Depth: *

1'-0"

Bathroom base cabinet depth: *

1'-10"

Project elevations scale: *

1. Exterior Elevations: 1/4"= 1'-0" 2. Interior Elevations: 1/2"= 1'-0"

What kind of building can an architect produce plans for? *

1. Institutional residential facility 2. private single family dwelling 3. multi family 4. Commercial building

Typical Text Sizes: *

1. Sheet Number: 1/2" 2. Main Titles: 1/4" 3. Subtitles, room names, notes, dimensions: 1/8"

Planning Checklist: *

1. Site analysis 2. Occupants 3. Individual Requirements 4.General Design 5. Budget Restrictions 6. Mechanical Equipment Required 7. Storage Areas Required

Project building section scale: *

1. Transverse Section: 1/4"= 1'-0" 2. Wall Section: 1/2"= 1'-0" or 3/4"= 1'-0" 3. Casework Section: 1"= 1'-0"

Cabinet Back: *

1/4" fir plywood

material used for a Drawer Bottom: *

1/4" fir plywood

Project floor plan scale: *

1/4"= 1'-0"

What size do we want the text used in dimensions to be when plotted full size (1:1)? *

1/8"

What scale is the object in model space?

100% or 1:1

what is the horizontal dimension of a roof pitch? *

12''

What is the spacing of the roof rafters? *

16" on center - applies to the distance between the center of one member to the center of the next member.

What should the text size be if the drawing is plotted at 3/4" = 1'-0"? *

2"

Kitchen Base Cabinet Depth: *

2'-0"

What is the typical space needed for a person to walk in?

2'-0"

Bathroom base cabinet height: *

2'-10"

What is the suggested minimum depth of a closet? *

2'-6"

What is the maximum width of a utility and bedroom door? *

2'-8"

what size will the text be for a plan scaled at 1/2" = 1'-0" if you want the size to match the subtitle text? *

3"

What is the space needed for a water closet? *

3'-0" centered

What is the typical door size at the exterior of a residential project? *

3'-0" x 6'-8"

What is the thickness of an exposed cabinet end? *

3/4"

Cabinet Partition: *

3/4" fir plywood or particle BD

Face frame: *

3/4" hardwood LBR stile and rail

Used to secure countertop to case: *

3/4" x 2-1/2" softwood LBR nailers

What is the minimum distance between the finished floor and grade? *

6"

What is the standard height of a residential door? *

6'-8"

Orthographic true name: *

90 degree drawing

Why is little added firestopping required in platform framing?

Because a firestop is inherently created by the double top plate at each floor.

What line is offset to locate the overhang? *

Exterior of framed wall

X-Refs: *

External references- Another drawing file LINKED to the one you are working on allowing more than one person to work on a project

What drawing contains the largest picture of the building and how it relates to all other drawings in the set of construction documents?

Floor Plan

Material used on exposed cabinet: *

Hardwoods

Ridge Board: *

In a gable roof framing, the top most member of the roof

Which hatch pattern in autocad is used to represent siding, both vertical and horizontal after it is rotated?

Masonry

What is on Dimension String 4? *

Overall

What is included in the Site Plan?

Reflects Designer work. Same info as the plot plan, PLUS... building footprint, travelways, parking, drainage facilities, sanitary sewer lines, water lines, trails, lighting, and landscaping and garden elements

Plot Plan: *

Resembles surveyor work. Basic legal/property info - an architecture, engineering, and/or landscape architecture plan drawing—diagram - shows the buildings, utility runs, and equipment layout, the position of roads, - other constructions of an existing or proposed project site at a defined scale.

What is plywood called when used on roof? *

Roof Decking

What is on Dimension String 2? *

Room Sizes

What kind of view is the floor plan?

Section

Which drawing allows the designer to see the exterior/interior space in the "Z" direction? *

Section

Which layer carries the most importance in a floor plan?

Walls

Traffic Patterns: *

Well placed living entrances allow a direct circulation path that does not interfere with the conversation circle

What is the difference between platform framing and Balloon framing?

balloon framing - the studs run in one piece from the sill to the rafter plate - Balloon framing has less vertical shrinkage from drying out of the wood platform framing, - the studs are interrupted by floor platforms. - platform framing is easier and safer to erect, uses shorter lengths of lumber for studs, and is automatically firestopped, for which reasons it has become the method of choice.

Layout view... *

bottom tag to set up the titleblock and add viewports

What framing member can be taken out for a different affect on the inside of the building?

ceiling joist

Fascia: *

covers the end of the rafter tails

Break Lines: *

cuts a drawing into multiple parts for easy view

Lines have varying widths and patterns to *

display important aspects about the object

What is on Dimension String 1? *

doors, windows, framing, masonry

What are the boards at the top of the wall called? *

double top plate

What board is the gutter attached to? *

fascia

What line can you measure from in an elevation? *

finish floor

Which drawings should be worked on simultaneously in designing a building?

floor plan, building section, elevations

3 Principle planes of projection: *

frontal, horizontal, profile

What is on Dimension String 3? *

geometry

Floor joist sit on: *

girder beam

The top view is in which plane of protection? *

horizontal

What do line widths express? *

important

Where is insulation installed? *

in all vertical walls and throughout attic

Perspective is... *

intuitive and dimensionally unstable

Sole Plate: *

is at the finish floor level

What requires the most time in foundations? *

laying the steel

What limits a building designer from producing a set of construction documents for a residence?

must be a single family residence

Oblique surface: *

never 90 degrees and requires three views to construct

What type of drawing has vanishing lines and cannot be dimensioned for construction?

perspective

The right and left side are on which principle plane of projection? *

profile

What are the horizontal members of a raised-panel door? *

rails

What do we use orthographic view for? *

resolve complex geometry

All text in a drawing should be readable in which two directions? *

right and bottom

Which dimension of a door is the most important to a framer? *

rough opening

What is the order of materials in the examples given for a brick veneer wall? *

sheet rock, stud, sheathing, air space, brick veneer

What is the purpose for placing the door swings and furniture into a plan? *

space planning

What are the vertical members of a raised-panel door? *

stiles

Which member of the wall structure carries the roof load? *

studs

Solar orientation in design looks at the location of the sun in the...

summer and winter

Why are doors uniquely numbered? *

swing, hardware, material, specialty items

What does steel add to the concrete slab? *

tensile strength, resists forces that bend and crack concrete

keyway: *

the indention in the footing that prevents the foundation wall from moving horizontally

Steel Stirrups: *

the metal that holds the rebar in place in the beams

Birdsmouth: *

the notch-out of the roof rafter

Polyethylene Moisture Barrier: *

the plastic sheeting that is between the compacted fill and sand/concrete

The planes of projection are parallel to the object face so... *

the projection lines are 90 degrees from the object

Why do we compact the soil under the slab? *

to prevent settling

The content of a set of drawings resembles what shape?

triangle

How are the doors unique from windows in their call outs?

unique number assigned

What is the element that identifies the header versus the jamb of a door and window detail?

vertical 2x's

What elevation cannot be constructed until drawing is produced?

wall section

Paper Space *

where the titleblock is located in Layout view

Model Space: *

where you work on the model through the viewport in Layout View

Dimension Scale Factor: *

whole number (xp denominator)

Miter Lines *

will allow two non-adjacent drawings to share information

What happens if the X-Ref file is renamed or moved? *

will remove the XRefed drawing from the drawing