Manual Trans Mid Term
Technician A says the third prong on a 110-volt electrical plug is for a safety ground. Technician B says the third prong on a 110-volt electrical plug can be removed before use. Who is correct A only B only both A and B neither A nor B
A only
Technician A says universal joints allow the drive shaft to change angles in response to rear axle movements. Technician B says universal joints keep the drive shaft length constant as the drive shaft changes angles. Who is correct? A only B only both A and B neither A nor B
A only
When reviewing the procedure for adjusting a clutch pedal, Technician A says that 1 inch of pedal free travel is normal on most vehicles. Technician B says that the clutch master cylinder pushrod should be adjusted for constant light pressure on the piston. Who is correct? A only B only Both A and B Neither A nor B
A only
_____ vehicles combine features of both rear- and front-wheel drive systems so power can be delivered to all wheels all the time or when the conditions or driver selects two- or four-wheel drive. AWD or 4WD FWD or RWD Hybrid All-terrain
AWD or 4WD
When installing a pressure plate, Technician A says that pressure plate bolts are tightened one at a time in a circular pattern. Technician B says that the dowel pins locate the pressure plate to ensure that proper balance of the clutch assembly is maintained. Who is correct? A only B only Both A and B Neither A nor B
B only
While discussing the ways to eliminate the problems caused by removing too much material from a flywheel while it was resurfaced, Technician A says the flywheel should be replaced so that a longer release bearing can be installed. Technician B says the problems may be corrected by installing a precision shim between the flywheel and the crankshaft. Who is correct? A only B only Both A and B Neither A nor B
B only
1. When discussing common causes of problems with clutch systems with adjustable linkage, Technician A says that often problems can be corrected by properly adjusting the clutch linkage. Technician B says that excessive clutch pedal free travel can indicate an excessively worn clutch disc. Who is correct? A only B only Both A and B Neither A nor B
Both A and B
When discussing self-adjusting clutch cables, Technician A says that a toothed wheel and a pawl are used to adjust the cable for clutch disc wear. Technician B says that the self-adjusting unit maintains the desired amount of free-play. Who is correct? A only B only Both A and B Neither A nor B
Both A and B
When discussing the causes of rapid clutch disc wear, Technician A says that driving habits influence how long a clutch assembly will last. Technician B says that insufficient pedal free travel will cause the disc to wear rapidly. Who is correct? A only B only Both A and B Neither A nor B
Both A and B
When discussing the possible causes for damage to the surface of a pressure plate, Technician A says that a worn clutch disc can score the surface. Technician B says that insufficient pedal free travel or riding the clutch can cause it to overheat. Who is correct? A only B only Both A and B Neither A nor B
Both A and B
While discussing power-flow through the forward gears of a typical transaxle, Technician A says the main speed gears freewheel around the output shaft unless they are locked to the shaft by the synchronizers. Technician B says the main speed gears are in constant mesh with their mating gears on the input shaft and rotate whenever the input shaft rotates. Who is correct? A only B only Both A and B Neither A nor B
Both A and B
When discussing gears and pulleys.Technician A says that gears are used to apply torque to other rotating parts of the drivetrain.Technician B says that variable pulleys are used to multiply torque or increase speed in many CVTs.Who is correct? a. A only b. B only c. Neither A nor B d. Neither A nor B
C. Both A and B
When discussing the purposes of a drivetrain;Technician A says that it connects the engine's power to the drive wheels.Technician B says that it controls the power to the drive wheels for safe turning of the vehicle.Who is correct?
C. Both A and B
____ fires are those in which wood, paper, and other ordinary materials are burning. Class A Class B Class C Class D
Class A
_____ fires are those involving flammable liquids, such as gasoline, diesel fuel, paint, grease, oil, and other similar liquids. Class A Class B Class C Class D
Class B
_____ fires are electrical fires. Class A Class B Class C Class D
Class C
____ fires are a unique type of fire in which the burning material is metal. Class A Class B Class C Class D
Class D
The type of bearing that can only control loads perpendicular to the shaft is a: a. roller bearing b. tapered roller bearing c. thrust bearing d. radial bearing
D. Radial Bearing
_____ are provided by manufacturers and suppliers in order to provide detail of the chemical composition and precautionary information for all products that can present health or safety hazards. Warning labels Hazardous wastes disclosures Material Safety Data Sheets Repair manuals
Material Safety Data Sheets
When reviewing the procedure for installing a clutch disc, Technician A says that the disc should always be installed with its hub and springs toward the engine. Technician B says that the splines of the disc should be clean, dry, and never oiled or greased. Who is correct? A only B only Both A and B Neither A nor B
Neither A nor B
Which government agency controls all safety and health issues of the automotive industry? EPA Department of Health and Human Services OSHA Department of Transportation
OSHA
A bell housing is another name for a clutch housing. True False
True
Clutch pedal free play travel is necessary to help protect the throwout bearing from unnecessary wear. True False
True
Clutch slippage while the clutch is engaged is particularly noticeable during acceleration and shifting. True False
True
Dual clutches used in self-shifting manual transmission designs improve shifting quality and driveability. True False
True
The clutch assembly is placed between the engine and transmission on nearly all cars and trucks. True False
True
The clutch disc is covered with frictional material on both sides. True False
True
The clutch shaft extends from the front of the transmission and is splined. True False
True
Worn linkage can make precise clutch free play adjustments difficult. True False
True
_____ should be immediately informed of all accidents that occur in the shop. The EPA Your supervisor OSHA The manufacturer
Your supervisor
When discussing 4WD components,Technician A says that 4WD vehicles typically use a transfer case to transfer engine torque to both a front and a rear driving axle.Technician B says that 4WD vehicles normally have two clutch assembles, two drive shafts, and three differentials. a. A only b. B only c. Both A and B d. Neither A nor B
a. A only
When discussing pilot bearings or bushings,Technician A says that they are often eliminated in front-wheel drive vehicles.Technician B says that they serve as a low-friction pivot point for the clutch linkage.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
a. A only
When discussing ways to prevent fires,Technician A says that all dirty and oily rags should be stored in approved containers.Technician B says that all dirty and oily rags should be kept in a pile until the end of the day, and then they should be moved to a suitable container.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
a. A only
When discussing why exhaust fumes should be vented outdoors or drawn into a ventilation/filtration system,Technician A says that exhaust gases contain amounts of carbon monoxide.Technician B says that carbon dioxide is an odorless, colorless, and deadly gas.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
a. A only
While discussing semi-centrifugal pressure plates,Technician A says they alter the holding force of the clutch assembly in response to engine speed.Technician B says they require high pedal effort at low engine speeds.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
a. A only
Which of the following statements about the torsional springs in a clutch disc are not true? a. They dampen vibrations coming from the transmission and drive shaft. b. They may be tuned to a particular engine and driveline. c. They cushion the sudden load on the disc when it is quickly engaged. d. They are only found on flexible clutch discs.
a. They dampen vibrations coming from the transmission and drive shaft.
How often should hazardous materials training be given? monthly quarterly annually only for new hires
annually
When discussing lifting procedures in the shop,Technician A says that correct vehicle lift points can be found in the owner's manual.Technician B says to always lift heavy objects with your legs, not your back.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
b. B only
When discussing the purpose of a flywheel,Technician A says that it increases engine torque.Technician B says that it acts as the driving member of the clutch assembly.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
b. B only
When discussing universal joints,Technician A says that they eliminate vibrations caused by the power pulses of the engine.Technician B says that they allow the drive shaft to change angles in response to movements of the car's suspension and rear axle assembly.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
b. B only
When discussing what to do first when an accident does occur,Technician A says that technicians should immediately determine the cause of the accident.Technician B says that technicians should respond immediately to prevent further injury or damage.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
b. B only
When discussing where a clutch disc is normally mounted,Technician A says that it is bolted to the flywheel.Technician B says that it is splined to the transmission input shaft.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
b. B only
Technician A says a self-adjusting clutch control cable may adjust itself when the pedal is depressed. Technician B says self adjusting cable-type clutches have constant-running release bearings. Who is correct? A only B only both A and B neither A nor B
both A and B
Technician A says a self-adjusting clutch control cable may adjust itself when the pedal is depressed. Technician B says self adjusting cable-type clutches have constant-running release bearings. Who is correct? A only B only both A and B neither A nor B
both A and B
Technician A says most current vehicles with cable clutch linkages are self-adjusting. Technician B says some current vehicles with cable clutch linkages have a manual adjusting system. Who is correct? A only B only both A and B neither A nor B
both A and B
Technician A says torsional springs allow the clutch disc and hub to twist slightly. Technician B says torsional springs cushion the sudden load on the disc when it is quickly engaged. Who is correct? A only B only both A and B neither A nor B
both A and B
Technician A says that accidents can be prevented by not having anything dangle near rotating equipment and parts.Technician B says that accidents can be prevented by having common sense.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing FWD vehicles.Technician A says that the differential is normally part of the transaxle assembly.Technician B says that the drive axles extend from the sides of the transaxle to the drive wheels.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing clutch components,Technician A says that the clutch disc is splined to the input shaft of the transmission.Technician B says that the clutch disc carries the engine's torque to the transmission when the clutch assembly is engaged.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing hazardous materials in the shop,Technician A says that Right-To-Know laws require that employees have access to information on hazardous materials.Technician B says that shops can hire full-service waste management firms to remove and dispose of hazardous wastes.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor Bc. both a and b
c. Both A and B
When discussing release bearings,Technician A says that constant running release bearings are used with hydraulically controlled clutches.Technician B says that the release bearing moves the pressure plate fingers to disengage the clutch.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing reverse gear,Technician A says reverse is accomplished by adding a third gear.Technician B says the reverse idler gear causes the driven gear to rotate in reverse.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing shop safety procedures,Technician A says that unsafe equipment should have its power disconnected and marked with a sign to warn others.Technician B says that protective eyewear must meet ANSI Z87.1 standards.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing simple first-aid procedures,Technician A says that if someone is overcome by carbon monoxide, get him or her fresh air immediately.Technician B says that burns should be cooled immediately by rinsing them in water.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing the operation of the clutch assembly,Technician A says that when the pedal is depressed, the release bearing is pushed against the release fingers of the pressure plate, which releases the plate's pressure on the clutch disc.Technician B says that the clutch disc is pressed against the flywheel by the pressure plate.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing the purpose of a differential,Technician A says that it allows for equal wheel speed when the vehicle is rounding a corner or curve.Technician B says that the ring and pinion in the drive axle multiplies the torque it receives from the transmission.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing the purpose of the flywheel,Technician A says that it serves as a heat sink for the clutch disc.Technician B says that it serves as a vibration dampener for the engine.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
When discussing ways to create an accident-free work environment,Technician A says that everyone in the shop should take full responsibility for ensuring safe work areas.Technician B says that the appearance and work habits of technicians can help prevent accidents.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
c. Both A and B
A _____ assembly is used to connect and disconnect the engine from the transmission. clutch gear bearing flywheel
clutch
Which component is the driven member of the clutch assembly? clutch disc flywheel pressure plate assembly release yoke
clutch disc
The _____ is a Y-shaped member into which the release bearing is attached. clutch linkage pressure plate clutch fork hub
clutch fork
What are the main components of the drive train? clutch, transmission, differential, and engine clutch, transmission, differential, and torque converter clutch, transmission, differential, and drive axles clutch, transmission, differential, and gear system
clutch, transmission, differential, and drive axles
Which is the correct cycle for a modern four-stroke cycle engine? exhaust, intake, combustion, compression combustion, exhaust, intake, compression compression, exhaust, intake, combustion intake, combustion, exhaust, compression
combustion, exhaust, intake, compression
A _____ is a unit which replaces the conventional release fork, pivot ball, linkage, and throw-out bearing. concentric slave cylinder pressure plate slave cylinder master cylinder
concentric slave cylinder
A caustic material is defined as being _____. volatile thick corrosive pathogenic
corrosive
When discussing the car's electrical system,Technician A says that you should always disconnect the positive battery cable first, then disconnect the negative cable.Technician B says that hybrid vehicle repair requires the use of latex gloves during service on the high-voltage system.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
d. Neither A nor B
When discussing the dual-clutch systems,Technician A says that all dual-clutch systems use wet clutches.Technician B says that dual-clutch systems require the use of a clutch pedal.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
d. Neither A nor B
When discussing the major components of a hydraulic clutch linkage,Technician A says that the master cylinder for the car's brakes is also used for the clutch.Technician B says that the slave cylinder is directly connected to the clutch pedal and increases hydraulic pressure as the pedal is depressed.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
d. Neither A nor B
While discussing hydraulic clutch systems,Technician A says the slave cylinder responds directly to the clutch pedal and sends hydraulic fluid to the clutch master cylinder.Technician B says the clutch delay valve between the master and slave cylinder allows for immediate clutch release.Who is correct? a. A only b. B only c. Both A and B d. Neither A nor B
d. Neither A nor B
The spring used in most pressure plates is a single _____. diaphragm spring coil spring fulcrum ring semi centrifugal spring
diaphragm spring
The spring used in most pressure plates is a single _____. diaphragm spring coil spring fulcrum ring semicentrifugal spring
diaphragm spring
Safety in an automotive repair shop is the responsibility of the employer and _____. the EPA the customers local regulatory agencies employees
employees
The clutch cover is bolted to the _____. friction disk flywheel car frame engine block
engine block
The primary purpose of a _____disc is to absorb power impulses from the engine that would otherwise be transmitted directly to the transmission. clutch rigid flexible friction
flexible
Vehicles with automatic transmissions have _____ instead of flywheels. pilot bearings flexplates clutch discs clutch shafts
flexplates
The _____ acts as a balancer for the engine and it smooths out, or dampens, engine torsional vibrations caused by firing pulses. flywheel flexplate clutch disc clutch shaft
flywheel
The clutch cover is bolted to the _____. friction disk flywheel car frame engine block
flywheel
When the clutch is engaged, spring force clamps the friction disk between the pressure plate and the _____. flywheel differential reaction plate clutch pedal
flywheel
Which component is the driven member of the clutch assembly? clutch disc flywheel pressure plate assembly release yoke
flywheel
Professional work ethics in an automotive shop include following proper procedures, being neat in your appearance, following basic safety rules, and _____. keeping your work area clean working as fast as you can doing what you think is best leaving tools laid out to save time for other coworkers
keeping your work area clean
The release levers in the typical coil spring type clutch pivot on the _____ and release lever yokes to move the pressure plate through its engagement and disengagement operations. springs levers threaded bolts pedestals
pedestals
In the semicentrifugal clutch, the force of the pressure plate against the friction disk increases with vehicle speed because of weights located on the _____. pressure plate flywheel release levers clutch shaft
release levers
n the semicentrifugal clutch, the force of the pressure plate against the friction disk increases with vehicle speed because of weights located on the _____. pressure plate flywheel release levers clutch shaft
release levers
Torque is a measurement of _____. the rate power is produced engine efficiency the amount of work performed rotating or turning effort
rotating or turning effort
When a gasoline container is opened, the fumes will _____. stay in the container spill over the neck and go to the floor rise into the atmosphere liquefy
spill over the neck and go to the floor
In the diaphragm-spring clutch, forward movement of the throw-out bearing causes the diaphragm spring to _____. straighten expand contract engage the disc
straighten
Which substance should be used to flush battery acid, fuel, or solvents which get into your eyes? water milk baking soda baking powder
water