NX Molded & Cast Part Design

Réussis tes devoirs et examens dès maintenant avec Quizwiz!

Which one of these command is the most efficient and preferable way to create stiffeners on molded parts? -Extrude -Rib -Thicken -Flange

-Rib

What feature can be used to create stiffening geometry to support other features? -Rib -Shell -Extrude -Gusset

-Rib

What tool allows a user to organize features into "folders" in the part navigator? -Feature Groups -Feature Folders -Feature Files -Feature Designs

-Feature Groups

Which one of these is not a type of creation in the Text command? -On Curve -Planar Text -On Face -3D Text

-3D Text

What is required to create a Bounded Plane? -An open set of 2D curves -A closed set of 2D curves -A closed set of 3D curves -An open set of 3D curves

-A closed set of 2D curves

What is a key difference between a Design Group and Feature Group? -A design group is used to organize the model -A design group can be deleted -A design group can be made active -A design Group can be used to control the updating of the model

-A design Group can be used to control the updating of the model

The Variational Sweep command can create which one of the following? -A surface tangent to other surfaces -A non-parametric surface -A surface controlled by only two sketches -A surface normal to other surfaces

-A surface tangent to other surfaces

Aside from Along Vector, what is the other type of creation method in the Helix command? -Along Face -Along CSYS -Along Pattern -Along Spine

-Along Spine

What command in NX can you use to create a surface from an open set of connected planar curves? -Bounded Plane -Studio Surface -Ruled Surface -Sheet

-Bounded Plane

What option is used to create a spline that is defined by using the average of selected points? -Through Points -By Nodes -Exact Spline -By Poles

-By Poles

What type of Studio Spline lets you create a spline by constructing and manipulating spline poles? -Through Points -Dynamic Poles -Pole Constructor -By Poles

-By Poles

What is a unique ability of Face Blend over Edge Blend? -Can create a blend between two connected faces -Can create a blend between two faces that are not connected -Can create a blend that is G1 tangent -Can create a blend that is G2 curvature

-Can create a blend between two faces that are not connected

When creating an offset curve, how do you switch from sharp corners to a radius corner based off the offset value? -Change the Cap Option to Extension Cap -This cant be done -Change the Cap Option to Arc Cap -Toggle symmetric offset

-Change the Cap Option to Arc Cap

Which one of these commands does not user Target Body and Tool Body selections? -Sew -Emboss Body -Combine -Trim and Extend

-Combine

What is a common recommended practice when it comes to edge blends? -Create them as soon as possible in the model -Create them at the end of the model history -Create them in the sketches, not on the model -Position features to blend tangent lines

-Create them at the end of the model history

Which of one of these actions cannot be performed when right-clicking on a feature in the Part Navigator? -Copy -Delete -Cut -Paste

-Cut

Which one of these is not a Boolean-type command in NX? -Cut -Unite -Subtract -Intersect

-Cut

What command can be used to generate an internal volume solid? -Extract Geometry - Body -Replace Face -Create Volume -Delete Face

-Delete Face

Which Synchronous Modeling command can be used to remove faces from a machining solid to represent the part as-cast or as it would appear at various stages in a manufacturing process? -Simplify Face -Offset Face -Delete Face -Cast Face

-Delete Face

What command in NX can you use to create a container to organize features within a part? -Design Group -Object Container -Feature Set -Appearance Designator

-Design Group

Which command would you use to apply taper or slope to faces, bodies, or from edges? -Soft Blend -Draft -Chamfer -Face Angle

-Draft

Which Synchronous Modeling command creates a new sketch of curves on the intersected faces of a solid body? -Silhouette Curve -Intersection Curve -Edit Cross Section -Sketch Settings

-Edit Cross Section

When using the Edit Cross Section command, what option opens the internal sketch for editing? -Edit Section Curves -Edit Sketch Curves -Edit Intersection Curves -Edit Profile Curves

-Edit Section Curves

Which tool can be used to analyze a part for model issues such as self-intersecting faces, sliver faces, and open sheet boundaries? -Optimize Geometry -Face Analysis -Information Object -Examine Geometry

-Examine Geometry

Which command is used to create an associative or non-associative body, point, curve, or datum by extracting from existing objects within the same part? -Extract Geometry -Copy Feature -Create Interpart Link -Duplicate Geometry

-Extract Geometry

If you need to make a duplicate solid body to modify, what command would you use? -Copy Body -Extract Geometry - Body -Duplicate Body -Extract Geometry - Region

-Extract Geometry - Body

To create a blend between three faces at the same time, what command would you use? -Edge Blend -Styled Blend -Aesthetic Face Blend -Face Blend

-Face Blend

What option in the Move Face command helps select faces of the model? -Face Locator -Face Selection -Face Finder -Face Rule

-Face Finder

Which one of these is not a type of creation in the Face Blend command? -Two-face -Three-face -Face and Vector -Feature Intersection Edge

-Face and Vector

When creating an extrude, what curve rule will ensure that you select all of the sketch curves? -Connected curves -region boundary curves -tangent curves -Feature Curves

-Feature Curves

What is a good reason to build a robust model? -For a test part that wont be reused -For an example part used in a demo -For a part you are giving to a competitor -For a part that will be reused for a long period of time

-For a part that will be reused for a long period of time

Which one of these is not a type of continuity in the Studio Spline command? -G4 (Smooth) -G1 (Tangent) -G2 (Curvature) -G3 (Flow)

-G4 (Smooth)

What command in NX can you use to create a helical curve with a specific number of turns, pitch, diameter, and turn direction? -Spiral -Helix -Tube -Law Curve

-Helix

What is a good curve tool to use to make custom threads? -Helix curve -Rotate curve -thread curve -derived curve

-Helix curve

The Rib feature can only be created in what situation? -In a pocket area were the rib extends down and to the side walls -There is no restriction on where ribs can be created -Must be created on the top of a model and projected down to the surface -Can only can be created on surface bodies

-In a pocket area were the rib extends down and to the side walls

How can you tell which design group is active? -In the part navigator, the sphere to the left of the group name is green -In the part navigator, the sphere to the left of the group name is red -In the part navigator, the sphere to the left of the group name is blue -In the part navigator, the sphere to the left of the group name is white

-In the part navigator, the sphere to the left of the group name is green

What two types of curves can you include/ignore when using the Edit Cross Section command? -Blends and Chamfers -Holes and Blends -Exterior Ribs and Blends -Interior Features and Blends

-Interior Features and Blends

Which Synchronous Modeling command can be used to transform faces in a linear direction, angular direction, or from point to point? -Relate Face -Motion Face -Move Face -Translate Face

-Move Face

Which Synchronous Modeling command can be used to transform faces in a linear direction, angular direction, or from point to point? -Relate Face -Move Face -Motion Face -Offset Face

-Move Face

Which of the following describes a G0 (zero) constraint? -Objects are contiguous and tangent, but they have a different curvature at the point of contact -Objects are tangent and have the same radius of curvature at contact -Objects are contiguous but not tangent -Objects have the same rate of change at the joint and then accelerate

-Objects are contiguous but not tangent

Which of the following describes a G2 constraint? -Objects are curvature continuous and rate of curvature change is zero at the point of contact -Objects are tangent and have the same radius of curvature at contact -Objects are contiguous but not tangent -Objects have the same rate of change at the joint and then accelerate

-Objects are tangent and have the same radius of curvature at contact

What Synchronous Modeling command is used to add or remove material from an area of a model? -Offset Region -Replace Face -Resize Face -Thicken Face

-Offset Region

Which Synchronous Modeling command can be used to offset a set of faces from their current location and adjust adjacent faces to accommodate? -Offset Region -Offset Surface -Offset Feature -Variable Offset

-Offset Region

What option in the extrude dialog will project an extrude to the side walls of a pocket? -Open Profile Smart Volume -draft -offset -direction

-Open Profile Smart Volume

Which synchronous modeling command can be used to merge cylindrical and conical split faces such as hole and boss geometry? -Optimize Face -Divide Face -Split Body -Make Coaxial

-Optimize Face

Using the Extract Geometry command, which one of these objects cannot be extracted? -PMI Annotation -Body -Composite Curve -Datum

-PMI Annotation

Synchronous modeling commands are best suited to be used on what types of parts? -Parts with prismatic bodies with parametric history -Parts with surface data -Parts with prismatic bodies with no parametric history -Parts with convergent bodies

-Parts with prismatic bodies with no parametric history

Which Synchronous Modeling command can be used to modify a body by adding or subtracting faces of a sheet body? -Paste Special -Add/Remove Face -Boolean Face -Paste Face

-Paste Face

In the Text command, what option allows you to automatically creates a text string expression from the generated text? -Reference Text -Use Kerning Spaces -Create Bounding Box Curves -Associative

-Reference Text

While using Delete Face, what Face Rule allows you to select many faces easily by using a seed face and boundary faces? -Feature Faces -Region Faces -Rib Faces -Adjacent Faces

-Region Faces

What should be done with expressions to make then easier to understand? -Delete the expression -Hide the expression -Reorder the expressions -Rename the expression

-Rename the expression

What can you do to important features in the part navigator to make them easier to find? -Hide the feature -Rename the feature -Reorder the feature -Suppress the feature

-Rename the feature

What option is used to create duplicate profiles in the Variational Sweep command? -Secondary Sections - Add New Set -Secondary Sections - Duplicate -Profile -Secondary Sections - Copy Profile -Secondary Sections - List Profiles

-Secondary Sections - Add New Set

Which command is used to combine multiple sheet bodies into a new single sheet body? -Join Face -Unite -Sew -Join Sheet

-Sew

What command could be used to create a hollow molded part? -hollow -Shell -subtract -split body

-Shell

The Draft command is typically used to apply what to faces? -An extrude -An offset -A hollow -Slope

-Slope

Which type of object can you add a rib into? -Solid Body -Sheet Body -Datum Plane -Assembly Component

-Solid Body

What commands are useful for modifying imported model data? -Just edit the exiting features imported thru the step file -Base group commands -Synchronous Modeling Commands -Construction group commands

-Synchronous Modeling Commands

When performing a Boolean operation such as Unite, which body retains all the object attributes such as material properties, color, and layer? -Tool Body -Target Body -Body Faces -All Bodies

-Target Body

What curve feature can be used to easily add lettering to a model? -Text -Law -Studio Spline -Emboss

-Text

What will happen when you edit a spline defined Through Points to a spline defined By Poles? -The defining data will be retained -The spline will become non-associative -The defining data will be lost -The spline can never be switched back to Through Points

-The defining data will be lost

When performing Boolean operations, what should you always pick? -The same tool body -A different target body -The same Target Body -Multiple tool bodies

-The same Target Body

Which of the statements is true when creating or moving the defining points of a Studio Spline? -You need to manually update the spline every time you move a defining point -You can only create a defining point but cannot move them once created -You can only move one defining point at a time -The spline curve dynamically update in real time

-The spline curve dynamically update in real time

What option is used to create a studio spline thru specific locations? -By Poles -By Nodes -Through Points -Exact Spline

-Through Points

In the Text command, which one of these cannot be used as a Font Style? -Regular -Underlined -Bold -Italic

-Underlined

Which one of these statements is false when constructing robust models? -Use the model for a one-off design project -Use the model as a reusable template part -Modify a copy of the model for use in the new product designs -Repeatedly make design changes

-Use the model for a one-off design project

What command in NX can you use to create a body by sweeping a cross section along a path where the shape of the section varies along the path? -Styled Sweep -Variational Sweep -Sweep Along Guide -Swept Volume

-Variational Sweep

When modeling custom threads, which command do you use to create a body by sweeping a cross section along a path where the shape of the section varies along the path? -Swept Volume -Styled Sweep -Variational Sweep -Helical Sweep

-Variational Sweep

To help avoid constraints to external objects, what selection scope can be used while working in a sketch? -Within work part only -Within active sketch only -Entire assembly -Within Design group only

-Within active sketch only

How can you capture company standards to build new parts? -create a Template part -create a Blank part -use a Standards File -import a company part into the current part

-create a Template part


Ensembles d'études connexes

Rhetoric in Reagan's Address at Moscow State University

View Set

Chapter 10: Motivation and Emotion

View Set

Fundamentals - Chapter 30: Bowel Elimination Care

View Set

Human Relationships - InThinking Questions

View Set

Travel Terminology = Trip-Related Terminology, Types of Journey, Flight Services and Reservation- Related Terms

View Set

Atmospheric pollution study Guide

View Set

Nursing Health Assessment- PrepU ch3

View Set