IB Design Technology - Topic 2
Quantification of carbon emissions
Defining numerically the carbon emissions generated by a particular product
Green design
Designing in a way that takes account of the environmental impact of the product throughout its life.
Incremental solutions
Products which are improved and developed over time leading to new versions and generations.
Clean technology
Products, services or processes that reduce waste and require the minimum amount of non-renewable resources.
Recondition
Rebuilding a product so that it is in an "as new" condition, and is generally used in the context of car engines and tyres.
Recycle
Recycling refers to using the materials from obsolete products to create other products.
Reserves
Reserves are natural resources that have been identified in terms of quantity and quality.
Resources
Resources are the stock or supply of materials that are available in a given context.
Re-use
Reuse of a product in the same context or in a different context
Design for the environment software
Software that allows designers to perform Life cycle analysis (LCA) on a product and assess its environmental impact.
System level solutions
Solutions that are implemented to deal with the whole system, rather than just components.
Recovery of raw materials
Strategies for the separation of components of a product in order to recover raw materials.
Waste mitigation strategies
Strategies used to reduce the waste produced by a product or in the production and disposal of a product.
End-of-pipe Technologies
Technology that is used to reduce pollutants and waste at the end of a process.
Individual energy generation
The ability of an individual to use devices to create small amounts of energy to run low-energy products.
The precautionary principle
The anticipation of potential problems in relation to the environmental impact of the production, use and disposal of a product.
Life cycle analysis (LCA)
The assessment of the effect a product has on the environment through five stages of its life: pre-production; production; distribution (including packaging); utilization; and disposal.
The prevention principle
The avoidance or minimization of producing waste in relation to the production, use and disposal of a product.
Renewability
The level at which a resource is renewable. The rate that a resource can be replenished.
Energy storage
The method with which energy is stored for later use.
Energy distriution
The method with which energy is transported from a source to where it is used.
Energy utilization
The method with which energy is used.
Cradle to Cradle
A design philosophy that aims to eliminate waste from the production, use and disposal of a product. It centres on products which are made to be made again
Cradle to Grave
A design philosophy that considers the environmental effects of a product all of the way from manufacture to disposal.
Eco-Design
A design strategy that focusses on three broad environmental categories - materials, energy, and pollution/waste.
Renewable resources
A natural resource that can replenished with the passage of time, or does not abate at all.
Non-renewable resources
A natural resource that cannot be re-made or re-grown as it does not naturally re-form at a rate that makes its use sustainable, for example, coal, petroleum and natural gas
Combined Heat and Power (CHP)
A system that simultaneously generates heat and electricity from either the combustion of fuel, or a solar heat collector.
Product cycle
Also known as the product life cycle, it is a cycle that every product goes through from introduction to withdrawal or discontinuation.
Linear economy
An economy based on the make, use, dispose model.
Circular economy
An economy model in which resources remain in use for as long as possible, from which maximum value is extracted while in use, and the products and materials are recovered and regenerated at the end of the product life cycle.
National and international grid system
An electrical supply distribution network that can be national or international. International grids allow electricity generated in one country to be used in another.
Local combined heat and power (CHP)
CHP plants that generate heat and power for a local community - the plant is close enough to the community so that the heat generated can be dispersed through the community efficiently.
Green legistation
Laws and regulations that are based on conservation and sustainability principles, followed by designers and manufacturers when creating green products.
Legislation
Laws considered collectively to address a certain topic.
Product recovery strategies
The processes of separating the component parts of a product to recover the parts and materials.
Repair
The reconstruction or renewal of any part of an existing structure or device.
Dematerialization
The reduction of total material and energy throughout of any product and service
Converging technologies
The synergistic merging of nanotechnology, biotechnology, information and communication technologies and cognitive science.
Embodied Energy
The total energy required to produce a product.
Re-engineer
To redesign components or products to improve their characteristics or performance.
Radical solutions
Where a completely new product is devised by going back to the roots of a problem and thinking about a solution in a different way