NETA 2 Combined study guide

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

Over your right shoulder

Facing the low-voltage side of a three phase transformer, where is H3?

synchronous

In a three-phase motor, the speed of rotation of the magnetic field is called the _____ speed.

at least one

How many persons on the confined space rescue team or service must hold a current certification in CPR?

343 lb-ft equation=Torque = HP x 5252 / RPM

How much torque is required to produce 300 HP at 4600 RPM?

voltmeter or phasing sticks

In addition to the proper PPE, what is the minimum equipment required to verify phasing on a 480V double-ended substation with drawout circuit breakers?

5

Type AC Cable must have a bending radius at least _____ times the diameter of the cable.

Occupational Safety and Health Administration

Who is the main federal agency charged with the enforcement of safety and health legislation?

8

six lines on a bolt head in the shape of a hexagon is a grade __ bolt

battery

what does this schematic symbol represent

Undercurrent/Underpower Relay

what is a 37 device

Manual Transfer Switch

what is a 43 device

Unbalance Relay

what is a 46 device

Instantaneous Overcurrent Relay

what is a 50 device

AC Time Overcurrent Relay

what is a 51 device

AC Circuit Breaker

what is a 52 device

Power Factor Relay

what is a 55 device

decrease

What happens to the inductance of an inductor as its core becomes saturated? Does the inductance value increase, decrease, or remain the same?

equation for total uF in series= 1 /( 1/12+1/20+1/30)=6 equation for Xc= 1 / (2(pi) * 400 * .000006) answer=66.32 ohms

Three capacitors, a 12 µF, a 20 µF, and a 30 µF, are connected in series to a 400 Hz source. The total XC is

53.05 ohms 1/(2*3.14*60*.00005)

Two capacitors, a 20 µF and a 30 µF, are connected in parallel to a 60 Hz source. The total capacitive reactance is

40kv

What is the NETA-MTS recommended maximum AC test voltage for a high-potential test on a single-phase, 27kV line sectionalizer with a rated impulse withstand voltage of 125kV?

650 equation=MVA = SC x (Max Voltage x 1.732) / 1,000,000

What is the calculated MVA rating for a 15kV Vacuum circuit breaker operating at 13.8kV with an interrupting rating of 1600A and a short circuit rating of 25kA?

10kV

What rms test voltage would you use to perform a VLF test on service aged cable rated 8kV according to NETA standards?

false

A single transfer switch may be used where a single generator supplies emergency loads and other loads.

feeders

Conductors between the service equipment or source of separately derived systems and a panelboard are defined as ____ .

100-2000mA

Considering a general 120V 60Hz hand-to-foot shock of one second, at approximately which current level would ventricular fibrillation occur?

Change current flow

What is the function of a circuit breaker?

Any value greater than 1.0

What is the minimum acceptable DAR value for a newly installed 150kW emergency generator?

47

What protective relay functions on a predetermined value of polyphase voltage in the desired phase sequence?

Velocity and displacement

What two quantities are usually measured with a circuit breaker motion analyzer?

TRUE

Capacitance is directly proportional to the area of the plates.

105A

A 4-20mA single CT has a max range of 150 amp what is the amps at 14mA?

Category 2

A given battery bank feeding a 208V UPS system has an available fault current of 1600A and an arc duration of 1.5 seconds. According to NFPA 70E, which of the following would be considered an acceptable Arc-Flash PPE Category for this equipment?

17.32 A

A delta-connected set of windings has a phase current of 10 A. The line current is

OFWF First Letter: Internal cooling medium in contact with the windings O: Mineral oil or synthetic insulating liquid with fire point < 300°C K: Insulating liquid with fire point > 300°C L: Insulating liquid with no measurable fire point Second Letter: Circulation mechanism for internal cooling medium N: Natural convection flow through cooling equipment and windings F: Forced circulation through cooling equipment (cooling pumps), natural convection flow in windings (non-direct flow) D: Forced circulation through cooling equipment, directed from the cooling equipment into at least the main windings Third Letter: External cooling medium A: Air W: Water Fourth Letter: Mechanism for external cooling medium N: Natural convection F: Forced convection

A modern oil-filled transformer is cooled by an oil/water heat exchanger mounted separately from the tank. What classification might this transformer have?

Proper chemical material mixing procedures

An MSDS is a document will normally not contain which of the following information?

Liquid transformers

Buchholz relays are used to protect:

7

Five lines on a bolt head in the shape of a pentagon is a grade __ bolt

100mW

For high-voltage bushings without a capacitance tap, at what level would a hot collar watt-loss test indicate possible contamination?

First-trip testing

From a safety perspective, which of the following tests is most important when servicing medium-voltage circuit breakers?

current

Galvanometers are used to measure what

1926.100

OSHA guidelines for head protection are referenced in:

two quarts

Sample valves should be flushed with at least _____ of waste liquid before collecting a transformer liquid sample.

Device/circuit operation

Schematic diagrams are principally utilized to show

good speed regulation

The shunt-type DC motor is known to have:

Apparent Power

The longest side of the power triangle represents which of the following:

class

The maximum intended AC voltage use of insulating blankets is identified by its ________ designation.

Faradays Law

Transformers work on which of the following principles:

primary

Voltage taps are usually located on the ____ side of a transformer.

Ground, Guard & UST

What are the three modes of operation using a power factor test set?

Hi-pot

What can be used to test a the integrity of vacuum bottles?

white

What color test decal you affix to a protective device that is electrically and mechanically acceptable?

21

What device functions when the circuit admittance, impedance or reactance increases or decreases beyond predetermined limits?

North American Electric Reliability Corporation

What does NERC stand for?

energy use

What does a kilowatt-hour meter read?

Whether there are defects in the cable that will fail under test conditions

What does a withstand test determine

300% overload

When testing an MCP what tests are not performed?

the metal end caps of ferrule fuses and the blades on knife-blade fuses.

When testing fuses, whether by resistance measurement or voltage measurement, the test probes should contact______________ or _______________.

1/3 way down side of cell

When using a hydrometer, where is the specific gravity of a cell taken?

Class 2

Which of the following hard hats would you choose to protect from blows to both the top and sides of the head?

Type 2

Which of the following hard hats would you choose to protect from blows to both the top and sides of the head?

500vdc

Which potential would you apply when performing an insulation resistance acceptance test on 300V rated cable?

47 DEVICE

Which protective relay functions on a predetermined value of polyphase voltage in the desired phase sequence?

Translay relay

Which relay is used to protect feeders?

1 or 2

the absence of lines on a bolt head is a grade __ bolt

5

three lines on a bolt head in the shape of a triangle is a grade __ bolt

relatively constant speed under varying loads

DC compound motors are used to operate loads that require:

Overvoltage Relay

what is a 59 device

AC Directional Overcurrent Relay

what is a 67 device

DC Circuit Breaker

what is a 72 device

AC Reclosing Relay

what is a 79 device

Automatic Transfer Relay

what is a 83 device

40 equation=15 +15+(1/(1/20+1/20))

what is the resistance from a to b


संबंधित स्टडी सेट्स

Pure substances and Mixtures Unit 1 Lesson 4

View Set

Chapter 7: Social Class - The Structure of Inequality

View Set

Torts I 2013 - Intentional Torts (#5 - Intentional infliction of emotional distress)

View Set

Health Policy Provisions, Clauses, and Riders

View Set