System Study Questions AMF BE99

अब Quizwiz के साथ अपने होमवर्क और परीक्षाओं को एस करें!

Why would the Red "in transit" Gear Handle Light be illuminated?

-when the gear is in transit -when the gear is not down and locked and N1 is 80% or less.

FUEL CROSSFEED meaning, memory items, checklist, how will affect flt.

- Green, means Fuel Crossfeed Valve is OPEN. Switch is in the crossfeed position. - No memory items -Use Abnormal Checklist to perform crossfeed of fuel.

Starter limitations

40 on 60 off 40 on 60 off 40 on 30 min off

How is fuel quantity measured?

5 probes supply information to each quantity gage and is measured in lbs

What are the GPU annunciators?

B: EXT POWER - means door is open C: EXT PWR - means there is proper polarity (gpu is connected)

How do we know if a 325amp current limiter has blown on? B model? C model?

B: right side - blowers inop, left side - flap motor inop C: respective side inverter inop

What type of Landing Gear System do we have?

Electrically Driven, Hydraulically Actuated, Mechanically Down Locked

What are the acceptable military fuel types?

JP4 JP5 JP8

What are the acceptable fuel types?

Jet A, Jet A1, Jet B, AVGAS -using anything other than Jet A/A1 contact MX

Explain bus-feeder-fault. How do you detect it on a Beech 99?

Means the 60amp feeder has blown and you detect that by seeing that bus has come offline and you would see the BUS FEEDER FAULT White light illuminate

Explain battery-feeder-fault. How do you detect it on a Beech 99?

Means the Ground Fault system has detected a fault in the lead and taken the battery offline. You detect that by seeing the battery has come offline and you would see the BAT FEEDER FAULT RESET Amber light illuminate

How does Landing gear stay down?

Mechanical locks in the actuator pistons lock the gear down and interrupt the current to the hydraulic pump motor turning off hydraulic pressure when all 3 landing gears are down and locked.

If for some crazy reason you need to have the fueler fill both NAC and Wing tanks for a top off, what is the sequence you need to tell them to fuel it?

NAC first then Wing tanks.

How are C model and B model low pressure fuel pumps driven?

C: 1 engine driven, 1 electrically B: both electrically

What major things are powered from L GEN BUS? C Model / B Model

C: Left Engine cowl lip heat, and CA window anti-ice B: Flap motor, windshield anti-ice, Left prop de-ice.

What major things are powered from Right Gen BUS? C Model / B Model

C: Right Engine cowl lip heat, vent blower, FO window anti-ice B: Main Stab. Trim, Blower, Landing gear motor, and Right prop de-ice

Will the battery discharge if the Cargo Lights are left ON after the Master is turned off?

No the cargo lights are on the Battery Bus

On a C model if the Primary boost pump fails what could also fail?

Oil Scavenger pump because they run off the same engine driven shaft. So you want to monitor the oil pressure and temperature when you see a Fuel Press annunciator.

How is the Nose Gear Door retracted and extended?

Pulled in and pushed out

What does the Bus Feeder Fault detection circuit do?

When a 60A Bus Tie blows it turns on the lighted annunciator.

During taxi the R DC GEN light illuminates, what is a possible cause? In reference to the previous question, you can verify that the generators are no longer paralleling due to a low electrical load by increasing the load via lights or increasing N1 above 60%

The load has dropped below .14 and the R DC GEN has gone offline True

What do the starters do?

They produce electricity to mechanically move the N1 shaft for engine starts.

What type of horizontal stabilizer do we have?

Variable Incidence Horizontal Stabilizer

Is there flap asymmetry protection?

no

If a generator goes "offline" with the system load below .14, should you reset it?

no dont reset it.

What does the Electrical System do? how does it work? (core concept)

provides electrical power to all of the rest of the systems. It is combined of 2 starter/generators and a battery.

What happens when you pull a T handle?

electrically close the Firewall Fuel Shutoff Valve and arm the fire extinguisher.

What powers the flaps?

electricity

On a B model during shutdown you want to keep the Primary Fuel Pumps on until what N1?

until N1 decreases to 5 % (C model is automatic because its engine driven.)

What unit of quantity do our fuel gauges show?

lbs

Which flap panel must agree with the flap handle?

left inboard

Ways you can verify the gear is down and locked

- You Do NOT hear horn with flaps full - You Do NOT hear horn with both N1 80% or less - No red in transit light in gear handle

What does the Ground Fault Detection System do for the battery and generators?

-Battery: detects a fault in the battery lead causing the battery relay and ground fault relay to open to take the battery offline. -Generator: detects a fault in the generator lead causing the ground fault sense relay to open and take that generator offline.

What happens when the starter is switched on?

-Energizes appropiate starter relay -Activates the appropiate engine igniton system. -B model Activates the purge valve -B model de activates the ground fault trip system.

What happens in the Landing Gear System when the Gear Handle is Selected DOWN?

-hydraulic pump motor is energized -power is REMOVED from up/down selector and sends pressure to gear actuators -move gear down -mechanical down locks in actuators lock it into position -All 3 gear are down, current to hydraulic pumps is interrupted and shuts off. -Red Gear Unsafe Light extinguishes

What happens in the Landing Gear System when the Gear Handle is Selected to UP?

-hydraulic pump motor is energized -power is applied to up/down selector and sends pressure to gear actuators -move gear up into wheel well -system continues to pressurize until 1850psi is sensed in the pressure switch. -if pressure decreases below 1400psi the pressure switch opens and the pump turns on to re-pressurize.

L/R FUEL PRES meaning, memory items, checklist, how will affect flt.

-Yellow Annunciator, lower annunciator panel -Loss of Fuel Pressure (low fuel pressure pump not working or producing less than 9 psi) -No memory item -Use Abnormal Checklist

What are the flap speeds?

0-30 is 170 30-full is 140

75 gallons of fuel = ______ hrs flight time

1 hr flt time

Fuel Crossfeed Toggle Switch activates what 3 things?

1. Opens the cross feed valve. 2. Activates the electric standby pump on the source side. (Regardless of switch position) 3. Electrically closes the motive flow valve on the receiving side to prevent fuel transfer to the receiving side NAC tank.

Maximum GPU output?

1000 amps

What are your VFR minimum fuel requirements? Per AMF? How much is 1 hour of reserve fuel?

135.209 30 mins for day, 45 for night. AMF policy: 1 hour of reserve VFR/IFR/Day or Night. If you have an alternate listed its still 1 hour 1 hr= 500lbs (75gal)

Flaps 30% indicate the flaps are at what degree? Full?

13° Full: 43°

What psi does the landing gear hydraulic pump turn on when the gear is retracted but lost pressure in the line?

1400psi

How many hours can we use AVGAS for before an overhaul is required? Other AVGAS restrictions?

150 hours C model: Limited to FL180 if you have a Fuel Press annunciator illuminated B model: 8,000' no matter what is failed or not failed.

What are our generators rated at?

30v B Model: 200 amps C Model: 250 amps

What are the minimum start voltages?

21.5 GPU 23.5 Battery Start

What is the total *useable* fuel capacity?

2466 lbs / 368 *gallons*

What kind of batter do we have? Where is it located?

24v, 40amp Lead Acid battery Located inside right wing root.

What is the least amount of fuel you can have for takeoff? (minimum fuel for t/o)

285 lbs (43 gal) per side 570 lbs total

What type of electrical system do we have?

28v DC system

How much fuel is being sensed in the NAC tank when a NAC NOT FULL annunciator is illuminated? How much will you see on the fuel gauges?

362 lbs (54 gallons) 550 lbs because of the 188 unusable in NAC tank.

What is our turning radius on the ground while taxing?

30 feet

How much fuel can the NAC tanks hold?

56 gal

What is the minimum N1 for generator online operation? Why?

60% N1 because generator could slow the compression section enough to create over temp conditions

What is the normal fuel consumption of the BE99?

600lbs for the first hour, 500lbs per hour thereafter.

500lbs of fuel equals how many gallons?

75gal

With normal fuel consumption, if you embarked on a two hour flight with 2000 lbs of fuel. How many lbs of fuel would you land with?

900 lbs

What operates the primary flight controls?

A. Cables, pulleys, and bell cranks.

What parts of the pitch trim may be inoperative?

A. All parts of the pitch trim system must be operative—it is not deferrable.

Q. May you takeoff with a NAC NOT FULL annunciator on? How can you fix it?

A. No you may not take off until this light is extinguished. You can fix it by turning on both boost pumps (B99) or by turning on the respective side standby boost pump on C99.

What happens if the jet transfer pump stops working (no motive flow)?

A. The nacelle tank will feed via gravity, however 28 gallons in each NAC Tank is unusable. (Which would mean 20 min less flying time for each NAC Tank, 40 minutes if you lost both.)

What has to be functional on the stabtrim system before you can take off?

All of it, you cannot take off with trim inop.

What are the major things that make the B model Electrical system different from the C model?

B Model has two extra systems. Ground Fault Detection System and Bus Feeder Fault Detection System

What does the AC bus power?

B Model: TQ, CA Attitude and HSI, Oil pres, fuel flow and qty gauges C Model: TQ and CA Attitude and HSI, volt/freq meter, inverter warning relay

Why doesn't the gear retract on the ground?

Because the Right Squat Switch interrupts power to gear motors when weight on wheels is sensed and engages the J-Hook

Are the fuel quantity gauges DC or AC powered?

C Model: DC B Model: AC (requires inverter to be on)

How is fuel transferred from the inboard tank to the NAC tank?

Motive flow through a jet transfer pump.

Why is a GPU a better option for starting?

Cooler start Prolongs battery life Reduces engine operating cost

What does the Fuel System do? (core concept)

Core concept is to provide fuel to the engine to create rapid ignition of fuel to air to power the engine. Fuel is also used to cool down oil.

What happens if the high pressure fuel pump fails?

Engine Failure

What should you consider when you see a L/R Fuel Press annunciator illuminate?

Fuel Press annunciator means the low pressure pump has failed. Now the fuel tanks are being gravity fed and you have 28 gallons (188 lbs) of unusable fuel in your NAC tanks. Also consider you have 10 hours of flt time before you need a High Pressure pump overhaul.

What bus is the T handle powered from?

Hot Battery Bus

How is does the landing gear stay retracted?

Hydraulic pressure, 1850 psi holds the gear up

Left Squat Switch Items

Left Cowl Heat - off on grnd, ON in flt Nose Wheel Steering - Enabled on grnd, Disabled in flt Hobbs Meter - Off on grnd, ON in Flt

Trim out of range warning sounds when..

Left Pwr lever is advanced to 90% with horizontal stabilizer trimmed outside the green arc while on the ground ONLY.

The flaps handle actuates which flap?

Left inboard flap

What do you need to do before a GPU is connected?

Make sure that Battery Master - ON, Gens - OFF

What items lights/annunciators are powered by the hot battery bus?

Nose baggage Pod Door Light/Annunciator

What are the functions of the Low pressure *STANDBY* boost pumps? not primary low pressure pump

Provide a head of pressure to the high pressure pump if the engine driven pump fails (C99), and to provide fuel pressure during crossfeed.

Right Squat Switch Items

Right Cowl heat - OFF on grnd, ON in flt Gear UP circuit - Disabled on grnd, Enabled in flt. J-Hook - Set on grnd, Retracted in flt Stab Trim Warning out of range- Enabled on grnd, Disabled in flt

Which flap panel gives sense to the indicator?

Right inboard

What are the steps to crossfeed fuel on a B model?

Sending side: Primary & Secondary pumps ON Receiving side: Primary & Secondary pumps OFF Turn on Crossfeed switch

After completing the Fuel Pressure Abnormal Checklist, why is it important to monitor oil temperature and pressure on a C Model 99?

The Engine Driven Low-Pressure fuel pump is on a common shaft that also drives the Oil Scavenge pumps

What is a J-Hook?

The J-Hook locks the gear Handle in the down position when the right squat switch senses weight on wheels.

Regarding the four flap panels that are utilized by the BE99, the flap position is sensed and sent to the indicator based on which flap panel?

The right inboard is where flap position is sensed and sent to the Indicator

Preflighting your C Model 99 you notice that the #2 Inverter is not working this could be caused by.

The right side 325 amp current limiter is blown

Why do we turn on the Battery before GPU connection?

To prevent the avionics from being fried. Battery Off- avionics relay closed and connected to power regardless of avionics master switch being on. Battery ON- avionics relay disconnects from battery until avionics master switch is turned on.

Gear Unsafe Horn will sound..

Whenever the gear is not down and locked and N1 is 80% or less Whenever flaps are selected FULL and the gear is not down and locked. This cannot be silenced.

Can Jet A with prist be used if needed?

Yes

What would happen if one of the fuel probes is inop or not working?

You would show an inaccurate reading of the fuel quantity because all 5 probes parallel each other to give an accurate readout

How do our brakes work?

apply pressure to pedals, shuttle valve moves to allow pressure flow to brakes

Why will you not hear a trim out of range warning in flight?

it is deactivated in flight with the right squat switch

What type of brakes do we have?

manual hydraulic brakes

What is parrelling?

means the generators are operating in parallel to each other. Basically just operating at the same time sharing the same loads. They start parallelling at .14 load.

For the generators what happens when over voltage is detected?

the over voltage system detects 32.5v or more and take the generator offline by opening the reverse current relay.

The flap position indicator gauge receives its information from the left or right flap position transmitter?

right inboard flap

You suspect that the right 325 Amps current limit failed. How do you confirm this?

the respective side inverter is inop

What is going on in the system when you select flaps full and you hear a warning horn?

the systems detects that your Gear is not down and locked.

When doing a battery start, why do we turn GEN 2 off before starting the left engine and then bring it back online after 10% N1?

we do that because starters draw 1000amps and you might blow a 325amp current limiter.


संबंधित स्टडी सेट्स

BIOL 1322 Nutrition & Diet Therapy Chapter 11 Homework

View Set

PUBLIC POLICY AND PROGRAM IMPLEMENTATION TEST

View Set