7-9
DHCPV4 process
1-DHCPDISCOVER 2-DHCPOFFER 3-DHCPREQUEST 4-DHCPACK
DHCP V6
1-DHCPv6 SOLICIT 2-DHCPv6 ADVERTISE 3-DHCPv6 REQUEST 4-DHCPv6 REPLY
Match the step number to the sequence of stages that occur during the HSRP failover process.
1-The forwarding router fails. 2-The standby router stops seeing hello messages from the forwarding router. 3-The standby router assumes the role of the forwarding router. 4-The new forwarding router assumes both the IP and MAC addresses of the virtual router.
The address pool of a DHCP server is configured with 10.19.44.0/24. The network administrator reserves 6 IP addresses for servers. How many IP addresses are left in the pool to be assigned to other hosts?
Calculate the maximum number of hosts available for the slash value and subtract the required static IP addresses required for the devices. /24 = 254 hosts /25 = 126 hosts /26 = 62 hosts /27 = 30 hosts /28 = 14 hosts
What protocol can be configured on gateway routers R1 and R2 that will allow traffic from the internal LAN to be load balanced across the two gateways to the Internet? GLBP*
GLBP, or Group Load Balancing Protocol, allows multiple routers to act as a single default gateway for hosts. GLBP load balances the traffic across the individual routers on a per host basis.
Match the FHRP protocols to the appropriate description.
GLBP-a Cisco proprietary FHRP that provides load sharing in addition to redundancy VRRP-an open standard FHRP that provides redundancy through use of a virtual routers master and one or more backups HSRP-a Cisco proprietary FHRP that provides redundancy through use of an active device and standby device
A network administrator is analyzing the features that are supported by different first-hop router redundancy protocols. Which statement describes a feature that is associated with HSRP?
HSRP uses active and standby routers.* (The HSRP first-hop router redundancy protocol is Cisco proprietary and supports standby and active devices. VRRPv2 and VRRPv3 are nonproprietary. GLBP is Cisco proprietary and supports load balancing between a group of redundant routers)
Which FHRP implementation is a nonproprietary protocol which relies on ICMP to provide IPv4 redundancy?
ICMP Router Discovery Protocol (IRDP)
Which statement describes HSRP?
It is used within a group of routers for selecting an active device and a standby device to provide gateway services to a LAN.* Explanation: It is VRRP that elects one router as the virtual router master, with the other routers acting as backups in case the virtual router master fails. HSRP is a Cisco-proprietary protocol. IRDP uses ICMP messages to allow IPv4 hosts to locate routers that provide IPv4 connectivity to other (nonlocal) IP networks. HSRP selects active and standby routers to provide gateway services to hosts on a LAN.
What is the keyword that is displayed on www.netacad.com?
Router (In order for the host to receive the address of the DNS server, the host must use stateless DHCPv6. The router is configured with the correct DHCPv6 pool, but is missing the command ipv6 nd other-config-flag that signals to the host that it should use DHCPv6 to get additional address information. This command should be added to the interface Gigabit0/0 configuration on the router.)
A client device on an Ethernet segment needs an IP address in order to communicate on the network. A DHCP server with IP address 192.168.1.1 has been configured and enabled on the network. How will a client device obtain a usable IP address for this network?
Send a DHCPDISCOVER message to physical address FF-FF-FF-FF-FF-FF. (Like IP addressing, there is also a special MAC address for broadcast purposes: FF-FF-FF-FF-FF-FF. When a DHCP client needs to send a DHCP Discover message in order to seek DHCP servers, the client will use this MAC address as the destination MAC address in the Ethernet frame. It does this because it has no knowledge of the IP and MAC addresses of DHCP servers.)
A small coffee shop is offering free Wi-Fi to customers. The network includes a wireless router and a DSL modem that is connected to the local phone company. What method is typically used to configure the connection to the phone company?
Set the WAN connection in the wireless router as a DHCP client. (In a SOHO environment, a wireless router connects to an ISP via a DSL or cable modem. The IP address between the wireless router and ISP site is typically assigned by the ISP through DHCP. The DSL modem does not manage IP address allocation.)
A company uses DHCP to manage IP address deployment for employee workstations. The IT department deploys multiple DHCP servers in the data center and uses DHCP relay agents to facilitate the DHCP requests from workstations. Which two UDP ports are used to forward DHCP traffic? (Choose two.)
The DHCP protocol operates with 2 UDP ports. UDP port 67 is the destination port for DHCP servers, and DHCP clients use UDP port 68.
Refer to the exhibit. A network administrator is configuring a router for DHCPv6 operation. Which conclusion can be drawn based on the commands?
The DHCPv6 is for the stateless DHCPv6 operation that is indicated by changing the O flag to 1 and leaving the M flag as default, which is 0. Therefore, it is not configured for stateful DHCPv6 operation. Although the DNS server has the interface ID 0010, clients in stateless DHCPv6 operation will configure their interface IDs either by EUI-64 or a random number. The ACAD_CLASS is the name of the DHCP pool, not the DHCP server name.
Refer to the exhibit. Which destination MAC address is used when frames are sent from the workstation to the default gateway?
The IP address of the virtual router acts as the default gateway for all the workstations. Therefore, the MAC address that is returned by the Address Resolution Protocol to the workstation will be the MAC address of the virtual router.
After a host has generated an IPv6 address by using the DHCPv6 or SLAAC process, how does the host verify that the address is unique and therefore usable?
The host sends an ICMPv6 neighbor solicitation message to the DHCP or SLAAC-learned address and if no neighbor advertisement is returned, the address is considered unique.* Explanation: Before a host can actually configure and use an IPv6 address learned through SLAAC or DHCP, the host must verify that no other host is already using that address. To verify that the address is indeed unique, the host sends an ICMPv6 neighbor solicitation to the address. If no neighbor advertisement is returned, the host considers the address to be unique and configures it on the interface.
Which command will allow a network administrator to check the IP address that is assigned to a particular MAC address
The show ip dhcp binding command will show the leases, including IP addresses, MAC addresses, lease expiration, type of lease, client ID, and user name.
Which DHCPv4 message will a client send to accept an IPv4 address that is offered by a DHCP server
When a DHCP client receives DHCPOFFER messages, it will send a broadcast DHCPREQUEST message for two purposes. First, it indicates to the offering DHCP server that it would like to accept the offer and bind the IP address. Second, it notifies any other responding DHCP servers that their offers are declined.
A company uses the SLAAC method to configure IPv6 addresses for the employee workstations. Which address will a client use as its default gateway?
When a PC is configured to use the SLAAC method for configuring IPv6 addresses, it will use the prefix and prefix-length information that is contained in the RA message, combined with a 64-bit interface ID (obtained by using the EUI-64 process or by using a random number that is generated by the client operating system), to form an IPv6 address. It uses the link-local address of the router interface that is attached to the LAN segment as its IPv6 default gateway address.
Which statement is true about DHCP operation?
When a device that is configured to use DHCP boots, the client broadcasts a DHCPDISCOVER message to identify any available DHCP servers on the network. (The client broadcasts a DHCPDISCOVER message to identify any available DHCP servers on the network. A DHCP server replies with a DHCPOFFER message. This message offers to the client a lease that contains such information as the IP address and subnet mask to be assigned, the IP address of the DNS server, and the IP address of the default gateway. After the client receives the lease, the received information must be renewed through another DHCPREQUEST message prior to the lease expiration.)
ip address dhcp interface configuration command
Which command, when issued in the interface configuration mode of a router, enables the interface to acquire an IPv4 address automatically from an ISP, when that link to the ISP is enabled? Explanation: The ip address dhcp interface configuration command configures an Ethernet interface as a DHCP clien
What is a result when the DHCP servers are not operational in a network?
Workstations are assigned with IP addresses in the 169.254.0.0/16 network. (When workstations are configured with obtaining IP address automatically but DHCP servers are not available to respond to the requests, a workstation can assign itself an IP addresses from the 169.254.0.0/16 network)
.A company uses DHCP servers to dynamically assign IPv4 addresses to employee workstations. The address lease duration is set as 5 days. An employee returns to the office after an absence of one week. When the employee boots the workstation, it sends a message to obtain an IP address. Which Layer 2 and Layer 3 destination addresses will the message contain?
hen the lease of a dynamically assigned IPv4 address has expired, a workstation will send a DHCPDISCOVER message to start the process of obtaining a valid IP address. Because the workstation does not know the addresses of DHCP servers, it sends the message via broadcast, with destination addresses of FF-FF-FF-FF-FF-FF and 255.255.255.255.
What information can be verified through the show ip dhcp binding command?
the IPv4 addresses that are assigned to hosts by the DHCP server (The show ip dhcp binding command shows a list of IPv4 addresses and the MAC addresses of the hosts to which they are assigned. Using this information an administrator can determine which host interfaces have been assigned to specific hosts)
A company uses the method SLAAC to configure IPv6 addresses for the workstations of the employees. A network administrator configured the IPv6 address on the LAN interface of the router. The interface status is UP. However, the workstations on the LAN segment did not obtain the correct prefix and prefix length. What else should be configured on the router that is attached to the LAN segment for the workstations to obtain the information?
A PC that is configured to use the SLAAC method obtains the IPv6 prefix and prefix length from a router. When the PC boots, it sends an RS message to inform the routers that it needs the information. A router sends an RA message that includes the required information. For a router to be able to send RA messages, it must be enabled as an IPv6 router by the unicast ipv6-routing command in global configuration mode. The other options are not used to enable IPv6 routing on a router.
Refer to the exhibit. What should be done to allow PC-A to receive an IPv6 address from the DHCPv6 server?
Add the ipv6 dhcp relay command to interface Fa0/0. (Client DHCPv6 messages are sent to a multicast address with link-local scope, which means that the messages will not be forwarded by routers. Because the client and server are on different subnets on different interfaces, the message will not reach the server. The router can be configured to relay the DHCPv6 messages from the client to the server by configuring the ipv6 dhcp relay command on the interface that is connected to the client.)
Which protocol automates assignment of IP addresses on a network, and which port number does it use? (Choose two.)
DHCP , 67 (DNS uses port 53 and translates URLs to IP addresses. SMB provides shared access to files and printers and uses port 445. Port 80 is used by HTTP. HTTP is a protocol used to communicate between a web browser and a server.)
What is one indication that a Windows computer did not receive an IPv4 address from a DHCP server
The computer receives an IP address that starts with 169.254. (When a Windows PC cannot communicate with an IPv4 DHCP server, the computer automatically assigns an IP address in the 169.254.0.0/16 range. Any other device on the same network that receives an address in the same range is reachable.)
Refer to the exhibit. A network administrator is configuring a router as a DHCPv6 server. The administrator issues a show ipv6 dhcp pool command to verify the configuration. Which statement explains the reason that the number of active clients is 0?
Under the stateless DHCPv6 configuration, indicated by the command ipv6 nd other-config-flag, the DHCPv6 server does not maintain the state information, because client IPv6 addresses are not managed by the DHCP server. Because the clients will configure their IPv6 addresses by combining the prefix/prefix-length and a self-generated interface ID, the ipv6 dhcp pool configuration does not need to specify the valid IPv6 address range. And because clients will use the link-local address of the router interface as the default gateway address, the default gateway address is not necessary.
A host PC is attempting to lease an address through DHCP. What message is sent by the server to let the client know it is able to use the provided IP information?
When a host uses DHCP to automatically configure an IP address, the typically sends two messages: the DHCPDISCOVER message and the DHCPREQUEST message. These two messages are usually sent as broadcasts to ensure that all DHCP servers receive them. The servers respond to these messages using DHCPOFFER, DHCPACK, and DHCPNACK messages, depending on the circumstance.