ASE G1

A charging system output test indicates that the alternator is not supplying the specified output. Technician A says that the drive belt could be worn and causing the lower than normal output. Technician B says that the drive belt tensioner could be faulty. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

C-Both Technicians A and B

Accessory drive belts are checked for all except. a. Cracks b. Wear c. Length d. Alignment

C-Length

What type of grease should be used to lubricate the slides on a disc brake caliper? a. Wheel bearing grease b. Chassis grease c. Silicone grease d. Any of the above

C-Silicone grease

Two technicians are discussing a ballooned oil filter. What is the most likely cause of this condition:

Closed oil pressure relief valve

Before road testing a vehicle to determine if the automatic transmission is performing normally, which should be performed? a. Check for any stored diagnostic trouble codes b. Check the fluid level c. Check the fluid condition and color d. All of the above

D- All of the above

Leaking antifreeze can be what color? a. Green b. Orange c. Red d. Any of the above

D- Any of the above

To flush a hydraulic clutch system, what should be used?

DOT 3

A tight timing belt makes what type of noise?

Whining

Why are drum brakes adjusted? a. To stop loose wheel bearings b. To prevent brake fluid evaporation c. To reduce fluid loss check d. To compensate for lining wear

d. To compensate for lining wear

Steering dampers can be used to reduce excessive __________.

positive caster

A starter is being replaced. What precautions are needed before performing this procedure? a. Disconnect the negative battery cable. b. Disconnect the positive battery cable c. Remove the starter fuse d. Disarm the driver's side airbag for safety

A- Disconnect the negative battery cable.

Thickness variation specification for most disc brake rotors is ____ a. 0.0005 b. 0.050 inch c. 0.050 inch d. 0.500 inch

A-0.0005

How many drum brake shoe support pads are located on each backing plate? a. 6 b. 4 c. 2 d. 8 or more depending on make and model of vehicle

A-6

When checking for vent temperatures, where should the measurement be made? a. At the center outlets b. At the outlet on the driver's side c. At the defroster vents d. At the passenger side AC vent

A-At the center outlets

Automatic transmission cooling lines are located_____. a. Between the transmission and the radiator b. Between the transmission and the rear axle c. Inside the transmission or transaxle d. Inside the HVAC module

A-Between the transmission and the radiator

The specified tire inflation pressure is found_____. a. On the driver's side door placard b. On the tire sidewall c. Either a or b d. None of the above

A-On the driver's side door placard

A vehicle's air conditioner blows cold air while driving at normal speeds, but warm while sitting at stop lights. The least-likely cause of this condition is:

Frozen expansion valve

The open circuit voltage (OCV) test on a fully charged battery should show which voltage?

12.6

A rear wheel drive vehicle has a loud clunk when the transmission is placed into gear and a vibration that increases with vehicle speed. Technician A says this is caused by loose universal joints. Technician B says this is caused by an unbalanced driveshaft. Who is correct? ("A" "B" or "Both")

A

A technician measures several spots around a brake rotor with an outside micrometer. Technician A says the technician is checking the rotor for thickness variation. Technician B says the technician is checking the rotor for lateral runout. Who is correct? ("A" "B" or "Both")

A

Two technicians are explaining radiator cap service. Technician A says a radiator cap is tested using a cooling system pressure tester. Technician B says when the radiator cap does not hold enough pressure, you can replace the cap gasket. Who is right?

A

A vehicle with power assist brakes has a hard brake pedal. Which of these is the most likely cause?

A Faulty Brake Booster

Which is the preferred method to bleed air from a power steering system? a. Raise the front wheel off the ground and turn the steering wheel lock to lock b. Start the engine and allow to idle c. Use a vacuum pump attached to the reservoir cap d. Use a bleeding tool

A-Raise the front wheel off the ground and turn the steering wheel lock to lock

Which step is NOT usually done when disarming an airbag system? a. Removing the airbag modules from the vehicle b. Removing the airbag fuse c. Disconnecting the electrical connector to the airbag d. Disconnecting the battery

A-Removing the airbag modules from the vehicle

When jump starting a vehicle, the last connection from another vehicle or a jump box should, be______. a. The connection to a good ground on the disabled vehicle away from the battery b. The connection to the negative terminal of the good vehicle c. The connection to the positive terminal of the disabled vehicle d. Any of the above

A-The connection to a good ground on the disabled vehicle away from the battery

A technician removes and replaces a worn lower radiator hose on a four cylinder engine. The vehicle overheats after the technician has replaced the hose and added coolant. Which of these is most likely the cause of this condition?

Air Pocket

A technician is unable to balance a tire on a vehicle that vibrates at speeds above 35 mph. Technician A says to continue adding weights around the rim up to 20 ounces. Technician B says to dismount the tire from the rim and inspect the inside for liquid or debris. Who is correct? ("A" "B" or "Both")

B

A vehicle pulls to the left only while braking. Technician A says this could be a restricted left front brake line. Technician B says this could be a frozen right front caliper. Who is correct? ("A" "B" or "Both")

B

During a cylinder leakage (leak-down) test, air is noticed coming out of the oil fill opening. Technician A says that the oil filter may be clogged. Technician B says that the piston rings may be worn or defective. Which technician is correct? (Letter only)

B

Engine mounts were recently replaced on a front wheel drive vehicle with independent suspension. The vehicle now has a steady pull to the left at all speeds. Technician A says this is most likely caused by loose motor mounts. Technician B says this is most likely caused by a misaligned engine cradle. Who is correct? ("A" "B" or "Both")

B

Technician A says that oil should be squirted into all of the cylinders before taking a compression test. Technician B says that if the compression greatly increases when some oil is squirted into the cylinders, it indicates defective or worn piston rings. Which technician is correct? (Letter only)

B

The headlights get brighter as the engine is revved and RPM's increase. Technician A says this is caused by a high capacity battery. Technician B says this is caused by a faulty voltage regulator. Who is correct? ("A" "B" or "Both")

B

The tread of a tire is worn in the center and not on the outer shoulders. Technician A says this is caused by an improper wheel alignment angle. Technician B says this is caused by an over-inflated tire. Who is correct? (Just the letter)

B

While performing an oil change the technician notices a red colored fluid leaking between the transmission and the engine. Technician A says this is caused by a leaking rear main seal. Technician B says this is caused by a leaking transmission pump seal. ("A" "B" or "Both")

B

What precautions are needed to be performed to help prevent air from getting trapped in the cooling system when replacing coolant? a. Use the proper antifreeze as specified b. Open bleeder valve(s) during filling c. Use premixed coolant d. Wear protective gloves

B- Open bleeder valves during filling

During a cylinder leakage (leak-down) test, air is noticed coming out of the oil fill opening. Technician A says that the oil filter may be clogged. Technician B says that the piston ringsmay be worn or defective. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

B- Technician B Only

Technician A says that oil should be squirted into all of the cylinders before taking a compression test. Technician B says that if the compression greatly increases when some oil is squirted into the cylinders, it indicates defective or worn piston rings. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

B- Technician B Only

What should be performed before adjusting the parking brake on a vehicle using front disc brakes and rear drum brakes? a. Check that the thickness of the front disc brake pads are with factory specifications b. Check for proper adjustment of the rear drum brake shoes. c. Check the brake fluid level d. All of the above

B-Check for proper adjustment of the rear drum brake shoes.

The air bag warning lamp flashes a few times when the vehicle is started and then stops flashing and goes out. This indicates _____. a. A fault has been detected in the air bag system b. Normal self-test of air bag system c. the air bag module requires recalibration d. Any of the above depending on make model and year of vehicle

B-Normal self-test of air bag system

13. When rotating tires/wheels using a modified "X" method on a front-wheel-drive vehicle, where should the right front wheel be placed? a. Right front b. Right rear c. Left front d. Left rear

B-Right rear

CV Joint boots should be carefully inspected during routine service because they are made from ____ and can be torn or ripped allowing the grease to escape. a. Steel b. Rubber or flexible plastic c. Aluminum d. Vinyl

B-Rubber or flexible plastic

A steering dampener looks like a____ a. bump stop b. Shock absorber c. Pulley d. Straight long steel rod

B-Shock absorber

Why does the brake pedal need to be depressed several times after replacing the disc brake pads? a. To seat the pads into the caliper piston assembly b. To force the pistons outward so that the pads contact the rotor c. To bed in the brake pads d. To break in the new pads

B-To force the pistons outward so that the pads contact the rotor

Where is the evaporator drain usually located? a. Behind the glove compartment b. Under the vehicle on the passenger side c. Under the hood near the AC compressor d. Any of the above depending on make, model and year of vehicle

B-Under the vehicle on the passenger side

Wear indicator ball joints indicate that they are worn enough to need replacement in what location? a. a line near the attaching not b. a raised area around the grease fitting c. A special type of rubber grease seal d. Any of the above depending on manufacture

B-a raised area around the grease fitting

A faulty thermostat is being replaced. Technician A says a stuck open thermostat will affect engine performance. Technician B says the thermostat controls the engine's operating temperature. Who is correct? ("A" "B" or "Both")

Both

A halogen bulb is being replaced in a headlight system. Technician A says to handle the bulb at it's base during installation. Technician B says to wear gloves or use a piece of paper when handling the glass portion of these bulbs. Who is correct? ("A" "B" or "Both")

Both

Technician A says a stuck open PCV valve will cause a lean fuel condition. Technician B says the PCV system removes blowby gases from the crankcase. Who is correct? ("A" "B" or "Both")

Both

Technician A says the auxiliary automatic transmission oil cooler is a small radiator separate from the engine radiator. Technician B says that if the automatic transmission oil cooler lines are found to be leaking, they are first tightened to specifications. Who is right?

Both

The engine of a vehicle will start, but is slow cranking. Technician A says there may be resistance in the starter circuit. Technician B says to perform a voltage drop test to test for excessive resistance in the starter circuit. Who is correct? ("A" "B" or "Both")

Both

The serpentine accessory drive belt of an engine squeaks but appears to be in good condition. Technician A says this could be caused by a faulty idler bearing. Technician B says to check the belt with a belt gauge. ("A" "B" or "Both")

Both

All the lights in a brake light circuit illuminate except one. The most likely cause is:

Bulb

Of the following, when replacing a CV (constant velocity) joint or boot, what is the last step before clamping the boot?

Burping

Two technicians are discussing a compression test. Technician A says that the engine should be cranked over with the pressure gauge installed for "4 puffs." Technician B says that the maximum difference between the highest-reading cylinder and the lowest-reading cylinder should be 20%. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

C- Both Technician A and B

When replacing an external fuel filter, best practices include______. a. Use the same brand as the original as the replacement filter b. Reuse the filter after cleaning c. Relieve fuel system pressure before removing the fuel line connections d. Tighten fasteners as tight as possible

C- Relieve fuel system pressure before removing the fuel line connections

The location of a refrigerant leak is often where what is seen? a. A clear liquid leaking or dripping b. A green mist is seen c. Any oily areas d. Any of the above

C-Any oily areas

Technician A says that memory functions can be kept when disconnecting a battery by connecting a "memory saver" to the lighter plug on many vehicles. Technician B says that memory functions can be kept when disconnecting a battery by connecting a "memory saver" to the 16 pin diagnostic link connector (DLC) on 1996 and newer vehicles. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

C-Both Technicians A and B

The voltage drop is being tested on a cranking circuit. Technician A says that the voltmeter test leads need to be placed at the battery positive and the other test lead to the starter terminal to measure the voltage drop on the positive part of the circuit. Technician B says that the engine has to be cranked using the starter to measure the voltage drop. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

C-Both Technicians A and B

Two technicians are discussing how to check a vacuum brake booster for proper operation. Technician A says that the brake pedal should be depressed and then the engine started. Technician B says that the vacuum booster is working normally if the booster is able to supply 2 or 3 assisted brake applications before becoming a hard to depress brake pedal. Which technician is correct? a. Technician A only b. Technician B only c. Both Technicians A and B d. Neither Technician A nor B

C-Both Technicians A and B

Drive axle (differential case) fluid is usually_____. a. Engine oil (usually SAE 5W-30 or SAE 10W-30) b. ATF c. Gear lube (usually SAE 80W-90) d. Any of the above

C-Gear lube (usually SAE 80W-90)

A TPMS relearn procedure involves performing the procedure starting with which tire? a. Right front b. Right rear c. Left front d. left rear

C-Left front

A coil spring is correctly installed in a SLA-type of suspension system if_____? a. The two holes on the lower control arm are covered by the spring b. The two holes are open in the lower control arm c. One hole is covered and the other hole is open or just partially open d. The spring tip shows at the upper spring mount

C-One hole is covered and the other hole is open or just partially open

A disc brake caliper does not move and one of the pads is worn more than the other. a. Normal for disc brakes b. The caliper piston is likely to be stuck c. The caliper slides are likely to be stuck d. The caliper dust shield could be leaking and causing this condition

C-The caliper slides are likely to be stuck

An engine's exhaust is white gray colored. Which of the following is causing this condition?

Coolant burning in the combustion chamber.

There is white exhaust smoke coming from the tailpipe of a vehicle well after the engine has been started. What is causing this condition?

Coolant in combustion chamber

When replacing a water pump, be sure to ______. a. Torque all fasteners to factory specifications b. Use a new gasket/ seal c. Check that the accessory drive belt is properly aligned and adjusted to the proper tension d. All of the above

D- All of the above

When using a scan tool to retrieve diagnostic trouble codes (DTCs), the technician should also _____. a. Check monitor status b. Check freeze frame data c. Record any stored DTCs d. All of the above

D- All of the above

Before replacing the filter in an automatic transmission/transaxle, why should service information be checked first? a. The filter may not be replaceable unless the unit is disassembled b. The filter may be a spin-on type filter c. The pan may be required to be removed d. Any of the above

D- Any of the above

Coolant should be tested for_____ a. Proper color b. Freezing point (temperature) c. Specific gravity d. Both b and c

D- Both B and c

A technician wants to check the current flow (amperes) in a circuit. What needs to be done? a. The circuit has to be disconnected and the meter leads connected in series with the circuit being tested b. An inductive meter could be used to measure the current if attached to a wire in the circuit. c. Set the meter to read DCA and then connect the meter leads to the positive and negative terminals of the battery. d. Either a or b

D- Either A or B

Brake lines should be inspected for what faults? a. Leaks b. Kinks c. Rust d. All of the above

D-All of the above

Cabin filters _______. a. May be accessed from inside the vehicle on the passenger side behind the glove compartment b. Under the hood on the passenger side. c. Should be replaced as part of regular maintenance d. All of the above

D-All of the above

The tires on an all-wheel- drive vehicle should all be______. a. Same brand and size b. Same inflation pressure c. Within 1/16 inch of the same tread depth d. All of the above

D-All of the above

When replacing steering or suspension parts, which precaution is needed to be performed? a. Fasteners tighten to factory specifications b. Most parts need to be replaced in pair (left and right side) c. The front wheels should be in the straight ahead position when the final parts are tighten d. All of the above

D-All of the above

Which statement is true about springs? a. Torsion bars are often adjustable to control ride height b. Leaf springs use a center bolt c. Spring can sag resulting in lower ride height d. All of the above

D-All of the above

Service information should be checked before replacing/adding manual transmission /transaxle fluid because it can be _____. a. Automatic transmission fluid (ATF) b. Engine oil c. Gear lube d. Any of the above

D-Any of the above

Where can the type of power steering fluid be found? a. On the reservoir fill cap b. In the owner's manual c. In service information d. Any of the above

D-Any of the above

Transfer case fluid is _____. a. Engine oil (usually SAE 5W-30 or SAE 10W-30) b. ATF c. Gear lube (usually SAE 80W-90) d. Any of the above are possible

D-Any of the above are possible

The type of brake fluid recommended for use in the master cylinder is____. a. DOT3 b. DOT4 c. DOT 4+ or LV d. Any of the above depending on the vehicle

D-Any of the above depending on the vehicle

Which statement(s) is/are true? a. If the red brake warning light is on, this could indicate a fault with the hydraulic system b. If the amber ABS warning light is on this indicates a fault with the ABS system c. If the red brake warning light is on, the vehicle should not be test driven d. Both a and c are correct

D-Both a and c are correct

When replacing light bulbs, a wise technician should ____. a. use caution working around the high voltage of a HID headlight system b. not touch the glass part of a halogen bulb c. use the specified trade number bulb as a replacement d. all of the above

D-all of the above

A vehicle blows blue/gray smoke from the tailpipe only when first started in the morning. The most likely cause of this condition is:

Leaking valve seal

An automatic transmission's fluid is pink and milky. Technician A says this is caused by engine overheating. Technician B says the transmission could have been overfilled and the fluid has become aerated. Who is correct?

Neither

What precautions are needed to be performed to help prevent air from getting trapped in the cooling system when replacing coolant?

Open the Bleeder Valve during filling

A front wheel drive vehicle has a clacking noise that only occurs while cornering. The technician suspects a faulty front axle. Which of these is most likely the cause?

Outer CV Joint

A RWD (rear wheel drive) transmission has a leaking output shaft seal on a vehicle with 25,000 miles on the odometer. The MOST likely cause for the leakage is:

Plugged Transmission Breather filter

A technician is rotating the tires using the modified X-method of tire rotation on a front-wheel-drive vehicle. Where should be the right front wheel placed?

Right Rear

A vehicle's right front wheel has a growling noise that increases with vehicle speed. The most likely cause is:

Worn out wheel bearing

This question has the word EXCEPT. For this question, look for the choice that would NOT cause the described situation. Read the entire question carefully before choosing your answer. All of the following cause compressor drive belt edge wear, EXCEPT: a. Clutch air gap b. Bent mounting bracket c. Damaged pulley d. Worn pulley bearing

a. Clutch air gap

Why should you never touch the tip of a halogen bulb? a. Oil from a finger can cause shortened bulb life. b. The glass will crack. c. You can get a significant burn and personal injury. d. The glass will melt from the heat of your finger.

a. Oil from a finger can cause shortened bulb life.

This question has the word EXCEPT. For this question, look for the choice that would NOT fit the described situation. Read the entire question carefully before choosing your answer. Close visual inspection of the power steering serpentine belt can reveal all the following, EXCEPT: a. Premature wear due to misalignment check b. Proper belt tension c. Correct orientation of dual belt application d. Proper belt seating in the pulley

b. Proper belt tension wrong

The starter motor was recently replaced and now makes a whining noise when starting. Which of the following is the MOST likely cause? a. Wrong starter installed b. Shims left out c. Defective solenoid d. Defective flywheel

b. Shims left out

A spongy brake pedal may be caused by which of the following? a. ABS Diagnostic Trouble Code set b. Frozen caliper piston c. Defective metering valve. d. Air in hydraulic system

d. Air in hydraulic system

A vehicle with an electronically controlled automatic transmission is being road tested for poor shifting. What should be done before doing a road test? a. Check wires and connectors for disconnects b. Check for DTCS (diagnostic trouble codes) c. Hook up the scan tool to the DLC (Data Link Connector) check d. Check transmission/transaxle fluid level

d. Check transmission/transaxle fluid level

To flush a hydraulic clutch system, what should be used? a. DOT 3 brake fluid or clutch fluid b. DOT 5 brake fluid c. Solvent d. Brake clean

A- DOT 3 brake fluid or clutch fluid

Why is a scan tool needed when checking the level of automatic transmission fluid? a. To determine the fluid temperature b. To check for any stored diagnostic trouble codes c. To check which solenoids inside the transmission/transaxle are active. d. To determine the fluid capacity

A-To determine the fluid temperature

Typical lug nut torque specifications for a passenger vehicle is usually____ a. 60-70 lb-ft b. 80-100 lb-ft c. 110-150 lb-ft d. 160-180 lb-ft

B- 80-100 lb-ft

A scan tool is likely to be needed to perform which operation? a. Measure rear toe (total) b. Calibrate steering angle sensor c. Center the steering wheel d. All of the above

B-Calibrate steering angle sensor