MEEB Chapter 14 - Principles of Electricity

Lakukan tugas rumah & ujian kamu dengan baik sekarang menggunakan Quizwiz!

A series circuit always contains what two things?

A voltage source - the battery - and the load - R. Resistance is normally neglected because they're usually very small compared to the little resistance.

In a parallel circuit the loads are what for current?

Additive

What is another name for an AC generator that alternating current is produced by?

Alternator

electrical insulator

An electrical insulator is a material whose internal electric charges do not flow freely, and therefore make it very hard to conduct an electric current under the influence of an electric field. A perfect insulator does not exist, because a portion of the insulator could become electrically conductive if the voltage applied across it exceeds the breakdown voltage. This is known as breakdown voltage of an insulator. Some materials such as glass, paper and Teflon, which have high resistivity, are very good electrical insulators. A much larger class of materials, even though they may have lower bulk resistivity, are still good enough to insulate electrical wiring and cables. Examples include rubber-like polymers and most plastics. Such materials can serve as practical and safe insulators for low to moderate voltages (hundreds, or even thousands, of volts)

• electric circuit (parallel, series)

Components of an electrical circuit or electronic circuit can be connected in many different ways. The two simplest of these are called series and parallel and occur very frequently. Components connected in series are connected along a single path, so the same current flows through all of the components.[1][2] Components connected in parallel are connected so the same voltage is applied to each component.[3] A circuit composed solely of components connected in series is known as a series circuit; likewise, one connected completely in parallel is known as a parallel circuit.

• reactance

In electrical and electronic systems, reactance is the opposition of a circuit element to a change of electric current or voltage, due to that element's inductance or capacitance. A built-up electric field resists the change of voltage on the element, while a magnetic field resists the change of current. The notion of reactance is similar to electrical resistance, but they differ in several respects. An ideal resistor has zero reactance, while ideal inductors and capacitors consist entirely of reactance. The magnitude of the reactance of an inductor is proportional to frequency, while the magnitude of the reactance of a capacitor is inversely proportional to frequency

• overall load factor

In electrical engineering the load factor is defined as the average load divided by the peak load in a specified time period.[1] Typical example of a large commercial electrical bill: kW Demand = 436 kW; kWh Use = 57,200 kWh; Number of days in billing cycle = 32d Load Factor [%] = (57,200 kWh / (32 days X 24 hours per day)) / 436 kW X 100% = 17.08%

• power factor (pf)

In electrical engineering, the power factor of an AC electrical power system is defined as the ratio of the real power flowing to the load, to the apparent power in the circuit,[1][2] and is a dimensionless number in the closed interval of -1 to 1. Real power is the capacity of the circuit for performing work in a particular time. Apparent power is the product of the current and voltage of the circuit. Due to energy stored in the load and returned to the source, or due to a non-linear load that distorts the wave shape of the current drawn from the source, the apparent power will be greater than the real power. A negative power factor occurs when the device (which is normally the load) generates power, which then flows back towards the device which is normally considered the generator.[3][4][5]

• conductor

In physics and electrical engineering, a conductor is an object or type of material that allows the flow of electrical current in one or more directions. For example, a wire is an electrical conductor that can carry electricity along its length.

What are the five levels of command control devices?

Level one - load scheduling and duty cycle control Level 2 -demand metering alarm Level 3 - automatic instantaneous demand control Level 4 - ideal curve control Level five - forecasting systems

Ohm's law

Ohm's law states that the current through a conductor between two points is directly proportional to the potential difference across the two points. Introducing the constant of proportionality, the resistance,[1] one arrives at the usual mathematical equation that describes this relationship:[2] I = \frac{V}{R}, where I is the current through the conductor in units of amperes, V is the potential difference measured across the conductor in units of volts, and R is the resistance of the conductor in units of ohms. More specifically, Ohm's law states that the R in this relation is constant, independent of the current.[3]

What is the ratio of the average power demand and the maximum power demand?

Overall load factor. It runs between 20% and 30% for typical household. This is what a kilowatt hour meter does.

Energy is a product of what two things?

Power and time

For Ohm's law the current is inversely proportional to what?

Resistance

What are the two basic electrical circuit arrangements?

Series and parallel

If the resistance drops what happens to the current?

The current rises

• electric resistance

The electrical resistance of an electrical conductor is the opposition to the passage of an electric current through that conductor. The inverse quantity is electrical conductance, the ease with which an electric current passes. Electrical resistance shares some conceptual parallels with the notion of mechanical friction. The SI unit of electrical resistance is the ohm (Ω), while electrical conductance is measured in siemens (S).

In a parallel circuit the total current in the circuit is sum of what?

The total current in the circuit is the sum of the individual currents flowing in the branches that is:

On a typical induction type kilowatt- hour meter dials register what?

Total disc revolutions that are proportional to energy.

In a parallel circuit Each load has the same what the across it?

Voltage

• electric potential or voltage

Voltage or electric potential tension (denoted ∆V or ∆U and measured in units of electric potential: volts, or joules per coulomb) is the electric energy charge difference of electric potential energy transported between two points.[1] Voltage is equal to the work done per unit of charge against a static electric field to move the charge between two points. A voltage may represent either a source of energy (electromotive force), or lost, used, or stored energy (potential drop). A voltmeter can be used to measure the voltage (or potential difference) between two points in a system; often a common reference potential such as the ground of the system is used as one of the points. Voltage can be caused by static electric fields, by electric current through a magnetic field, by time-varying magnetic fields, or some combination of these three.[2][3]

What is a parallel or multiple circuit?

When two or more branches with loads are connected between the same two points


Set pelajaran terkait

A&P II Ch. 22 The Lymphatic System and Immunity

View Set

Week 2 Ch 33 Management of Patients With Nonmalignant Hematologic Disorders

View Set

Ch12: Outlining and Revising Your Speech

View Set

Exam #2-Endocrine Crises: DKA vs. HHS

View Set

Chapter 8 - Business Markets and Buying Behavior

View Set

Photosynthesis & Cellular Respiration

View Set