2

Ace your homework & exams now with Quizwiz!

Assuming the same operating frequency, what are the advantages of DDR3 over DDR2?

- DDR3 doubles the data transfer rate of DDR2 - DDR3 uses less power than DDR2

What is true about the DIsplayPort interface for connecting video monitors to computers?

- DisplayPort can send both video and audio signals over the same cable - DisplayPort uses a lower voltage than DVI or HDMI

What are magnetic storage devices?

- Tape drive - Hard disk - Floppy disk

When would you use the degauss feature on a CRT monitor?

- The monitor displays strange colors - The monitor displays distorted images

What are considered input devices?

- Touchscreen - Trackball

Under what conditions should you choose exFAT over FAT32 or NTFS?

- When creating a volume over 32 GB in size - When formatting removable flash devices

What should you when your computer system locks up and automatically restarts?

- check the CPU fan power - make sure there is thermal paste between the heat sink and the CPU

What are two major disadvantages to overclocking the CPU?

- increased heat output - voided warranty

You have a motherboard using an ATX form factor but a PC case using BTX. What do you do?

- return ATX motherboard and replace with a BTX - purchase an ATX form factor case

What is true regarding a dual-channel memory bandwidth configuration?

- the memory controller must support dual-channels - bandwidth is increased by 5-15%

Select the voltages provided by an ATX power supply (select three)

1) 3.3 2) 5 3) 12

Which of the following statements are true? (select two)

1) 32-bit processors use only the IA-32 instruction set (also referred to as x86) 2) 64-bit processors use the x86-64 instruction set (also referred to as x64)

Which of the following motherboard power connectors typically connect directly to the motherboard? (select two)

1) 4-pin CUP power 2) 24-pin motherboard power

Which of the following are true of the SXGA screen resolution? (select two)

1) 5:4 aspect ratio 2) 1280 x 1024

During the POST, you recieve a message stating: Keyboard not present. Press F1 to continue. What are the most likely causes of this error message? (select two)

1) A poor keyboard connection 2) A stuck key on the keyboard

One day while trying to start your Windows XP computer, the system displays the following error: Windows could not start because the following file is missing or corrupt: Windows\system32\ntoskrnl.exe. Please re-install a copy of the above file. The problem occurs immediately after the OS loading message. You are unable to boot into Safe Mode. Which of the following will most likely fix the problem? (select two)

1) Boot into the recovery console and runbootcfg /rebuild 2) Boot into the recovery console and perform an automatic OS scan and repair

Which of the following objects should have thermal paste applied? (select two)

1) CPU 2) Heat sink

Which of the following are CRT monitor characteristics? (select two)

1) CRT monitors use an electron beam that hits phosphor dots inside of a vacuum tube 2) CRT monitors have a 4:3 aspect ratio which matches the display ratio of a T.V. set.

You have just finished upgrading the CPU in your desktop system. After running the system for about 15 minutes, the system spontaneously shuts down. What should you do first to troubleshoot the problem? (select two)

1) Check the CPU fan power 2) Check the thermal shutdown threshold in the BIOS

You have just purchased a new plug-and-play sound card that uses a PCI slot. What should you do before installing the device in your Windows system? (select two)

1) Check the HCL to make sure the device is compatible with the version of Windows running on your system 2) Download the latest driver from the manufacturer's web site

Your laptop has an ExpressCard /54 slot. Which of the following is true? (select two)

1) Compatible ExpressCards for the laptop include cards which are rectangular-shaped 2) You can use an ExpressCard /34 card or an ExpressCard /54 card in the laptop

Your lobby receptionist uses a laptop computer to complete her day-to-day tasks. You are concerned about the security of her system. What should you do? (select two)

1) Configure the laptop with a biometric fingerprint scanner 2) Secure the laptop to the desk using a cable lock

You are in the process of building a new computer. You would like to configure your computer to use SLI to improve performance when playing your favorite game. Which of the following will be part of the configuration process? (select two)

1) Connect a monitor to one DVI port 2) Purchase a motherboard with two (or more) PCIe x16 slots

What should you do (if possible) before flashing the BIOS? (select two)

1) Connect the computer to an UPS 2) Backup CMOS settings

Lately your computer is spontaneously shutting down after only a few minutes of use. What is the most likely cause? (select two)

1) Cooling fans clogged with dust 2) Overheating CPU

Assuming the same operating frequency, what are the advantages of DDR3 over DDR2? (select two)

1) DDR3 uses less power than DDR2 2) DDR3 doubles the data transfer rate of DDR2

Which of the following video card connectors provides digital video output? (select two)

1) DVI-D 2) HDMI

When you try to read a particular DVD-R, you receive an error message. Other discs work fine. Which of the following are the most likely problems? (select two)

1) Dirty or scratched disc 2) Incorrect disc format

Which of the following statements are true about the DisplayPort interface for connecting video monitors to computers? (select two)

1) DisplayPort uses a lower voltage than DVI or HDMI 2) DisplayPort can send both video and audio signals over the same cable

Which techniques are used in a pharming attack to redirect legitimate Web traffic to malicious Web sites? (select two)

1) Exploiding DHCP servers to deliver the IP address of poisoned DNS servers 2) Changing the hosts file on a user's computer

Which of the following are magnetic storage devices? (choose three)

1) Floppy disk 2) Tape drive 3) Hard disk

You need to replace the power supply in your desktop. As you choose the replacement power supply, which of the following specifications are the most likely to affect your choice? (choose three)

1) Form factor 2) Processor connector 3) Output wattage

Which of the following connectors are part of the system case and connect to the header pins on the motherboard? (select two)

1) HDD LED light 2) Power Switch

Which storage device types use magnetic film or aluminum platters for storing data? (select two)

1) Hard disk 2) Floppy disk

You want to purchase a home theater. Which hardware selection criteria would be most important for this system? (select two)

1) Home Theater PC (HTPC) form factor 2) Video card with HDMI output

You have a small wireless network with less than 50 client computers. You upgrade the hardware on two wireless devices so you can use a better security standard than WEP. Now you need to implement the new security standard. You need the greatest amount of security with the least amount of effort, and without replacing any of the wireless infrastructure. What should you do? (select two)

1) Implement WPA2-AES 2) Configure each client with the same key

What is the major difference between the BTX and the ATX standards? (select two)

1) Improved thermal management 2) Processor slot rotated 45 degrees

You are linking multiple video cards together to increase performance. Which of the following statements are true? (select two)

1) In most cases both cards should be identical 2) Scalable Link Interface (SLI) and CrossFire are two different methods for linking video cards

Which of the following are advantages of solid state storage compared to hard drives? (select two)

1) Lower power requirements 2) No moving parts

You have just finished installing a new SATA HDD in your computer. Now, your SATA DVD drive won't work. What should you do first? (select two)

1) Make sure that the DVD SATA cable is connected 2) Make sure that the DVD power cable is connected

You have just finished the upgrading the CPU in your desktop system. After running the system for about 15 minutes, the system locks up and automatically restarts. What should you do first to troubleshoot the problem? (select two)

1) Make sure there is thermal paste between the heat sink and the CPU 2) Check the CPU fan power

Which of the following features is typically available through TRS ports on a sound card? (select two)

1) Microphone In 2) Speaker Out

Which of the following functions are associated with an AMR riser card? (select two)

1) Modem 2) Audio

the PS/2 ports on a computer are used for which types of devices? (select two)

1) Mouse 2) Keyboard

Which of the following tools can you use to start the Print Spooler service if it is currently stopped? (select two)

1) Net start 2) Services console

You're configuring devices on a SCSI bus. You've installed a SCSI adapter in an expansion slot. You've connected a SCSI HDD (sd0) to one of the middle connectors on the internal SCSI ribbon cable. The end connector on the internal SCSI ribbon cable is connected to the SCSI DVD drive. Where should termination be enabled on this bus? (select two)

1) On the SCSI adapter 2) On the DVD drive

You're configuring devices on a SCSI bus. You've installed a SCSI adapter in an expansion slot. You've connected an external SCI tape drive to the external port on the adapter. you've connected two hard SCSI HDDs (sd0 and sd1) to two of the middle connectors on the interlan SCSI ribbon cable. The end connector on the internal SCSI ribbon cable is connected to a SCSI DVD drive. Where should termination be enabled on this bus? (select two)

1) On the external tape drive 2) On the DVD drive

Which of the following expansion buses are most commonly used for video cards in modern computers? (select two)

1) PCI Express 2) AGP

To test a power supply, you want to use a multimeter to measure the voltage on a Molex HDD connector. To do this, you need to turn the power on. Which pins on the 24-pin motherboard connector coming from the power supply can be shunted to turn the power on? (select two)

1) Pins 15 & 16 2) Pins 16 & 17

You have added a new 1 TB HDD to a windows computer. The disk is configured as a basic disk. Which of the following can be configured on this disk? (select two)

1) Primary partitions 2) Extended partitions with logical drives

While browsing the Internet, the Internet Explorer browser window hangs and stops responding. Which Task Manager tab would you use to end Internet Explorer? (select two)

1) Processes 2) Applications

You want to be able to watch live TV on your computer and record TV shows from over-the-air digital TV stations. Your computer already has a video card, so you want to purchase an add-on card to provide the TV tuner input capabilities. Which of the following should be part of the configuration process? (select two)

1) Purchase a card that supports ATSC 2) Connect the TV input to the tuner card using coaxial cable and F-type connectors

You have an existing system that has a single DDR3 memory module installed. You would like to add more memory to the three remaining empty memory slots. What should you do to make sure you get the right memory for the system? (select two)

1) Purchase additional modules that are the same as what is currently installed 2) Check the motherboard documentation to find which modules are supported

You decide to upgrade your PC to use a faster processor. To do this, you ordered a new motherboard over the Internet that supports the processor you want to use. However, when it arrives, you discover that the motherboard uses the ATX form factor. Your existing PC's case uses the BTX form factor. What options do you have in this situation? (select two)

1) Purchase an ATX form factor case 2) Return the motherboard and replace it with a BTX form factor motherboard

You have been tasked with designing a workstation that will run VMware Workstation hypervisor software. It will be used by a software engineer to run virtual machines for app testing. Which criteria should be included in your design for this system? (select two)

1) RAM configured to run in triple-channel mode 2) 64-bit processor with 6 cores

You have been told to replace the HDD on a laptop computer that has a drive bay accessible from the outside of the computer. Which of the following should you do after powering down the system? (select two)

1) Remove the battery 2) Unplug the AC power

You want to upgrade the memory modules in a notebook computer. What are the most common ways to access the memory slots? (select two)

1) Remove the keyboard 2) Open a panel on the bottom of the notebook

You have connected two drives to the primary IDE interface in a PC system. How could the drives be configures? (select two)

1) Set both drives to Cable Select 2) Set one drive to Master and the other to Slave

You recently upgraded a client's older workstation from Windows XP to Windows 7. The client has called to complain that the new interface is very slow. For example, after clicking the Start button, the Start Menu slowly appears on the screen. How can you fix this problem? (select two)

1) Set the visual effects for Best Performance 2) upgrade the video board installed in the system

You're troubleshooting a malfunctioning notebook computer. Nothing appears on the LCD display when the system is powered on. When you connect an external monitor to the system, the Windows desktop is displayed properly on the monitor. What could be causing this problem?

1) The LCD assembly is malfunctioning 2) The display output has been redirected to the external monitor port using the Fn key

You're troubleshooting a malfunctioning notebook computer system. The user has indicated that the screen suddenly became dark and difficult to read while he was downloading a large file through his wireless network card while the system was plugged in at his desk. You've checked the system and determined that the backlight has stopped working. Which of the following could be the cause? (select two)

1) The cold cathode fluorescent lamp has burned out and needs to be replaced 2) The inverter in the LCD assembly has malfunctioned

You are installing an updated driver for a hardware device on your system. A dialog box displays indicating that Microsoft has digitally signed the driver you are installing. What benefits does driver signing provide? (select two)

1) The driver has been tested by Microsoft 2) The driver file has not been altered

Which of the following are true regarding a dual-channel memory bandwidth configuration? (select two)

1) The memory controller must support dual-channels. 2) Bandwidth is increased by 5-15%

Which of the following statements are true regarding power supply wattage? (select two)

1) The wattage requirement for each individual circuit uses this formula: W = V * A 2) A "watt" describes how much work or how much power can be supplied to various devices

Which of the following are considered input devices? (select two)

1) Touchscreen 2) Trackball

Which of the following cards can be placed in a Type III PC Card slot? (select three)

1) Type III PC card 2) Type II PC card 3) Type I PC card

You're attempting to diagnose a problem with a notebook computer. The user reports that it displayed a message that the batter was low, then it shut down by itself even though it was plugged into a wall outlet. You've checked the AC adapter and found that the LED light it lit when plugged into a wall outlet. What should you do next? (select two)

1) Verify that the power LED on the notebook computer is lit when plugged into the wall outlet 2) Verify that the AC adapter produces the correct DC voltage for the notebook computer

A customer has brought a computer in to be repaired. he has indicated that the sound board has stopped working as no audio is produced when music, video, or DVDs are played. What should you do first? (select two)

1) Verify that the volume isn't muted 2) Verify that the speakers are plugged into the correct jack and are powered on

Which of the following identify the key differences between a worm and a virus? (select two)

1) Worms independently replicate themselves 2) A virus relies on a host for replication

In which of the following situations would restoring from a backup be the best option? (select two)

1) You accidentally deleted several important e-mails from Outlook and need to restore them. 2) You need to restore several word processing files that were accidentally deleted from My Documents

A system board has four 32-bit RIMM slots. You have installed one RIMM. Which of the following are correct? (select two)

1) You can complete the installation by installing three continuity modules 2) You can complete the installation by installing three more RIMMs

You are troubleshooting a network communication problem to the www.widgets.com server. Which of the following will give you the IP address of that server? (select two)

1) nslookup www.widgets.com 2) ping www.widgets.com

You have a computer that is connected to the Internet through a NAT router. You want to use a private addressing scheme for your computer. Which of the following IP addresses could you assign to the computer?

10.0.12.15 172.18.188.67 192.168.12.253

What is the maximum range of the Bluetooth 2.0 specification for Class 1 devices?

100 M

You have a small home network that uses 192.168.1.0 with the default subnet mask for the network address. The default gateway address is 192.168.1254, the router is providing DHCP on the network. The Wrk2 computer has been assigned to IP address of 192.168.1.55. Which of the following is considered the loopback address for the Wrk2 computer?

127.0.0.1 127.0.0.1 is the loopback address for any device. This special address means "this host." If you ping the lookback address, TCP/IP configuration will be tested. A successful test means that TCP/IP is correctly configured on the host. 192.168.1.55 is the current IP address assigned to the host. You can ping this address, but the address is not considered the loopback address. Also, to tests the current host regardless of its current IP address. 192.168.1.255 is the broadcast address for the network meaning "any host" on the network.

Which of the following IP addresses have a default subnet mask of 255.255.0.0?

129.0.0.1 191.168.2.15 168.16.5.1 IP addresses are divided into classes. The most common of these are classes A, B, and C. Each address class has a different default subnet mask. To identify the class of an IP address, look at its first octet. Class A networks use a default subnet mask of 255.0.0.0 and have 0-126 as their first octet. Class B networks use a default subnet mask of 255.255.0.0 and have 128-191 as their fist octet. Class C networks use a default subnet mask of 255.255.255.0 and have 192-223 as their fist octet. In this question, the IP address that fall in the Class B IP address range are 191.168.2.15, 129.0.0.1, and 168.16.5.1.

Which of the following IP address ranges is reserved for Automatic Private IP Addressing?

169.254.0.1 - 169.254.255.254 The Internet Assigned Numbers Authority (IANA) has reserved 169.254.0.1 through 169.254.255.254 for Automatic Private IP Addressing (APIPA). APIPA also sets the subnet mask on the network to 255.255.0.0.

Given that your Windows workstation has Automatic Private IP Addressing (APIPA) implemented using default settings, which of the following TCP/IP addresses could be automatically assigned to the system should your DHCP server go down or become inaccessible?

169.254.1.26

Which of the following is a valid IP address?

172.16.1.26 2.2.2.2 A valid IPv4 address consists of 4 8-bit (1 byte) numbers separated by periods. For example, 10.0.0.65. Because they are 8 bits long, these numbers are frequently called octets. Even though we typically express these numbers using decimal notation, it's important to remember that these numbers are binary numbers. The lowest value one of these numbers can have is 00000000. The decimal equivalent for this number is simply 0. The highest value one these numbers can take is 11111111. The decimal equivalent of this number is 255. Therefore, in decimal notation, each octet must contain a number between 0 and 255 inclusively.

Which feature makes it possible to close some notebook computers and still use the touchscreen?

180 degree rotating touchscreen

Which of the following IP address are Class C addresses?

192.15.5.55 223.16.5.0 222.55.0.0 The following are class C addresses: 192.15.5.55, 22.55.0.0, and 223.16.5.0. The first octet of Class C addresses is in the range of 192 to 223. The first octet of Class A addresses range from 1-126. The first octet of Class B addresses range from 128-191.

List the steps you need to follow to add more disk space to a Storage Space in Windows 10. Drag the correct steps from the left to the correct step number on the right.

1st step - Install a new storage device to the system 2nd step - Add free space on a new storage device to a storage pool 3rd step - Allocate space from a storage pool to an existing storage space When you need more disk space for your storage spaces, follow these steps: -Install a new storage device to the system -Add the free space on that device to a storage pool -Allocate space to an existing storage space

How many PATA devices can be installed on a typical modern ATX motherboard?

2

How many PATA devices can be installed on a typical modern ATX motherbord?

2

You need to replace the HDD in your laptop computer. Which of the following HDD sizes would you likely choose for the laptop?

2.5"

What is the maximum total amount of RAM that can be installed on a system with 4 GB memory limitation with two 512 MB memory modules installed?

3 GB

You have a computer that has four DDR2 memory slots. Currently there are two 512 MB memory modules installed. You check the motherboard documentation and find that the system has a 4 GB memory limitation. You want to add as much memory as possible without replacing the existing modules. What is the maximum amount of RAM that can be installed in the system?

3 GB

Which tool would you use to grab and lift small objects?

3-prong holder

You have been asked to implement a RAID 5 solution for an engineer's desktop workstation. What is the minimum number of hard disks that can be used to configure RAID 5?

3. A RAID 5 array *stripes data and *parity information across multiple hard disks. TO complete a RAID 5 array, a minimum of three hard disks is required. A RAID 0 and RAID 1 can both be implemented with a minimum of two hard disks. *RAID 0 (also known as a stripe set or striped volume) splits ("stripes") data evenly across two or more disks, without parity information, redundancy, or fault tolerance. *RAID parity. ... Parity computations are used in RAID drive arrays for fault tolerance by calculating the data in two drives and storing the results on a third. The parity is computed by XOR'ing a bit from drive 1 with a bit from drive 2 and storing the result on drive 3 (to learn about XOR, see OR).

All other things equal, which of the following processor sizes will consume the least amount of power?

32 nm

What processor size will consume the least amount of power?

32 nm

What is the read speed of the drive?

32x/12x/48x

What is the approx bus speed of DDR2 memory rated at PC2-5300?

333 MHz

What is the max number of SATA devices you can connect to the motherboard with 4 built-in SATA connector using integrated ports.

4

You have a motherboard with 4 built-in SATA connectors. What is the maximum number of SATA devices you can connect to the motherboard using the integrated ports?

4

You have been asked to implement a RAID 10 solution for a video editor's desktop workstation. What is the minimum number of HDDs that can be used to configure RAID 10

4

What SCSI ID has been assigned to a device that has been placed on the first and three jumpers?

5

What is the maximum data transfer speed for USB 3.0 devices?

5 Gbps

You've just installed the DNS service on a Windows server. Which port must be opened in the server's firewall to allow clients to access the service?

53 The DNS service runs on port 53 by default. Port 110 is used by the POP3 protocol. Port 143 is used by the IMAP protocol. Port 123 is used by the NTP protocol.

You are designing an update to your client's wireless network. The existing wireless network uses 802.11b equipment, which your client complains runs too slowly. She wants to upgrade the network to run at 150 Mbps. Due to budget constraints, your client wants to upgrade only the wireless access points in the network this year. Next year, she will upgrade the wireless network boards in her users' workstations. She has also indicated that the system must continue to function during the transition period. Which 802.11 standard will work best in this situation?

802.11n

During the POST, you receive a message stating; Keyboard not present. Press F1 to continue. What are the most likely causes of this error message?

A stuck key on the keyboard A poor keyboard connection

Which mobile device architecture is used by Apple iPad devices running the iOS operating system?

ARM

In preparation to use your laptop on the airplane as you travel to a conference, you disconnected the USB mouse. However, after removing the external mouse, the cursor drifts consistently to the left side of the screen while using the built-in trackpad and mouse button. What should you do?

Access the BIOS/UEFI configuration and disable the USB pointer option

Which partition type identifies the partition as one that holds the boot loader program used to start operating system?

Active The active partition identifies which partition holds the boot loader code. When the system starts, it looks in the volume boot record (VBR) of the active partition to identify the location of the boot loader code. The system partition is the partition that holds the operating system files. This might be the same as the active partition, but can be different. A primary partition is a partition type on a basic disk. An active partition must be a primary partition, but there can be additional non-active primary partitions on a disk. An extended partition is a partition type that is subdivided into logical drives. The extended partition cannot be the active partition.

If you want to boot from a hard drive, what must it have?

Active partition The active partition contains the boot sector, which is required to load an operating system . An extended partition is a partition type on a basic disk. An extended partition can exist, but is not required to boot.

You have a computer with an onboard LAN adapter. The LAN adapter has failed and you are unable to connect the computer to the network. What should you do?

Add a NIC using a PCI slot

You have a 64-bit Windows 7 workstation with three shared printers. You want to add drivers for 32-bit versions of the OS. What method would you choose to add the drivers with the least amount of effort?

Add the drivers to your print server in Print Management

A customer complains that a recently purchased monitor no longer displays a picture. You verify that the monitor is powered on and that the video cable is securely fastened to the video port. Which of the following actions should you direct the customer to take?

Adjust the monitor's settings using controls on the monitor

You manage a computer that runs Windows 7. You want to create a new user account and allow the user to create and save files, install applications, and change the system. What group membership should you assign for the new user?

Administrators

You are the administrator for your company and have been asked to get the company accounting program installed on some new Windows 7 laptops. When you install this software on the new PCs, you discover that it will not run because User Account Control (UAC) keeps causing it to fail. Because the accounting program was designed by the company and it will not be upgraded anytime soon, you must get it to work as is with the UAC. What can you do to get the application to work with UAC?

Alter the program settings to Run This Program As An Administrator

You have a use who takes his laptop home every day after work. When he's working in the office, the laptop must get an IP address from the DHCP server so you configure it to obtain IP and DNS information automatically. When he's working from home, the laptop must use IP and DNS information that connects with his home network. Which IP addressing method can you use to make sure he gets a network connection at home?

Alternate IP Configuration With an Alternate IP Configuration, the systems's IPv4 Properties are configured on the General tab to use DHCP to automatically obtain TCP/IP configuration information. If a DHCP server cannot be contacted, the static IP configuration information on the IPv4 Properties' Alternate Configuration tab is used.

Of the following, which would most likely cause a random system lockup?

An overheated processor

What combination of monitors can you connect to a video card without additional conversion units?

Analog CRT monitor and digital LCD monitor

You have a video card with a DB-15 connector and a DVI-D connector. Which of the following combinations of monitors can you connect to the video card without additional conversion units? (assuming you have the necessary cables)

Analog CRT monitor and digital LCD monitor

Device manufactures are countless

Android

Open source and most popular mobile device operating system

Android

A company executive has just bought a new android mobile device. She wants you to help her make sure it is protected from malware threats. What options are available and important to use to protect Android devices?

App reviews and ratings will help you choose an effective anti-virus app Anti-virus app are available for purchase from Android app stores

Which Blu-ray standard defines rewritable disks?

BD-RE

Which of the following components is an example of firmware?

BIOS

Which of the following represents the correct boot sequence in Windows XP after the BIOS has passed control over to the NTLRDR?

BOOT.INI, NTDETECT.COM, NTOSKRNL.EXE

You have a computer where a removable disk drive has been formatted with NTFS. You want the drive to use FAT32 to be compatible with more operating systems. The drive is currently configured using drive letter D:. What should you do?

Back up the data on the D: drive, Reformat the D: drive using FAT32. Restore the data

The drive is currently configured using drive letter D:. What should you do?

Back up the data on the D: drive. Reformat the D: drive using FAT32. Restore the data.

Which LCD component is used to illuminate a notebook computer's display?

Backlight

What should you do before flashing the BIOS?

Backup CMOS settings

Which of the following devices would you add to a computer if you needed to take inventory at a retail store by scanning the UPC symbols on products?

Bar card reader

Which device would you add to a computer if you needed to take inventory at a retail store by scanning the UPC symbols on products?

Bar code reader

Which disk types does Windows support? (Select two.)

Basic Dynamic Windows supports basic and dynamic disks. When you install Windows, your hard disks are automatically initialized as basic. You can convert them to dynamic disks after Windows is installed. You can use both basic and dynamic disks on the same computer system, but a volume consisting of multiple disks, such as a mirrored volume, must use only one type of disk. Primary and extended are terms that describe partition types on basic disks.

Match the disk types on the left with the corresponding descriptions and features on the right. Each disk type may be used once, more than once, or not at all. -Support up to 128 volumes -Used primary and extended partitions -Supported by all operating systems -Support volumes that use discontiguous disk space -Store partitioning information in a hidden database on all such disks in the system -Only support volumes made up of contiguous disk space

Basic disks include the following characteristics: -Use primary and extended partitions -Supported by all operating systems -Only support volumes made up of contiguous disk space Dynamic disks include the following characteristics: -Support up to 128 volumes -Support volumes that use discontiguous disk space -Store partitioning information in a hidden database on all such disks in the system

Where should the thermal paste go when installing a processor?

Between the heat sink and the CPU

Greg, a graphic artist, installs a new art application on his Windows 7 computer. The application prompts Greg to install an updated video driver, which is unsigned. Greg accepts the unsigned driver and completes the installation. Greg uses the system for several days, and then reports that his display doesn't seem to refresh properly under some conditions. You want to configure Greg's computer to use the previous video driver until the manufacturer provides a signed driver, but he still needs to be able to use the application he installed. What should you do?

Boot the system into Safe Mode. Open Device Manager and select the video driver. Open the driver's properties and select Roll Back Driver

You connected a single drive to the primary IDE and single drive to the secondary IDE. How should the drives be configured?

Both drives should be set to Master or Single Drive only

You have connected a single drive to the primary IDE interface and a single drive to the secondary IDE interface. How should the drives be configured?

Both drives should be set to Master or Single Drive only

What stores important system information related to the starting of a computer?

CMOS memory

Which of the following stores important system information related to the starting of a computer?

CMOS memory

What objects should have thermal paste applied?

CPU and heat sink

What is the correct order for installing a processor for proper cooling?

CPU, thermal paste, heat sink, fan

Six months ago, you purchased a new laptop. Since then, you have noticed that the battery life has been steadily going don. When it was new, a full charge lasted about 3 hours. Now youa re lucky to get 2 hours before the battery charge level drops below 5%. What should be your first step to correct this problem?

Calibrate the battery

A user reports that they are unable to access their Firewire drive after moving the PC from beneath the desk to the top of the desk. What is the most likely cause of this problem?

Card is not seated properly

You have a Windows 7 system with two SATA HDDs, one used for the OS and the other used for data. You have traced recent problems to a fault in the system motherboard. You replaced the motherboard and reconnected all hardware. When you start the computer, the system shows the BIOS information screen, but then returns an error that an OS could not be found. What should you do?

Change the boot order in the BIOS

You have just installed a new USB card reader in your Windows computer. Every time you perform a certain action using the card reader, you get an error message that you've never seen before. What should you do first?

Check the manufacturer's Web site for information about the error

You recently purchased a new sound card and installed it in a free PCI slot in your computer. You plug in your old speakers, but don't get any sound. You checked all cable connections and they are secure. You have also ensured that the speaker volume is appropriately adjusted and isn't muted. What should you do next?

Check the vendor's web site for an updated driver

You want to configure your Windows 10 workstation such tha tit can get Windows updates directly from other Windows 10 systems on the network that have already downloaded them from Microsoft.

Choose how updates are delivered

You want to upgrade all memory in your system with the fastest memory available. Which of the following would you choose?

Choose the type of memory that is supported by your motherboard

Which tool can you use in Control Panel to control how times, dates, numbers, and currency are formatted and displayed for your computer?

Clock, Language, and Region

You use your computer to type documents in Portuguese that will be sent to Brazil. You purchase a second keyboard designed specifically for Portuguese. Which option in Control Panel would you use to configure your computer for the new keyboard so you can switch between the Portuguese and English keyboard?

Clock, Language, and Region

You want to configure your computer so that a password is required before the OS will load. What should you do?

Configure a user password in the BIOS

You have a Windows system shared by three shift workers. Files that are used by all users are stored on the D:/ drive in various folders. The users have created hundreds of files on this drive and sometimes experience difficulty finding the files they need. What should you do?

Configure indexing to include the D: /drive.

Your lobby receptionist uses a laptop computer to complete her day-to-day tasks. You are concerned about the security of her system. What should you do?

Configure the laptop with a biometric fingerprint scanner. Secure the laptop to the desk using a cable lock

What is the surest way to prevent the loss of important information on your mobile device if it is lost, stolen, destroyed, or there is a natural disaster?

Configure your device to remotely backup important data to the Cloud.

You are installing a PCIe video card in a new computer. The video card has connectors for both monitors. The card has a fan, but the fan does not draw power from the PCIe bus to operate. Which of the following will be part of the installation?

Connect a 6 or 8-pin power connector to the video card

You are installing a PCIe video card in a new computer. The video card has connectors for two monitors. The card has a fan, but the fan does not draw power from the PCIe bus to operate. Which of the following will be part of the installation?

Connect a 6- or 8-pin power connector to the video card

If a notebook computer is exhibiting symptoms that seem to indicate a malfunctioning keyboard, what troubleshooting steps can you take to determine if keyboard needs to be replaced?

Connect an external keyboard Check for special keyboard features that could e enable that may cause some keys to perform alternate tasks

You have just installed a new IDE DVD drive in your computer to replace the one that stopped working. When you play a music CD, you cannot hear any sound coming from your computer speakers. When you try to play a file saved on the hard disk, everything works correctly. What should you do?

Connect the audio port on the DVD drive to the audio input on the sound card or motherboard

What should you do (if possible) before flashing the BIOS?

Connect the computer to a UPS

You have just replaced the motherboard in your computer. Your computer starts, but the hard disk light does not come on while the system is booting. What should you do?

Connect the hard disk LED to the motherboard

You have just replaced the motherboard in your PC. Now your PC will not start. You press the power button on the system case, but nothing happens; there are no sounds or lights. What should you do?

Connect the power button to the motherboard

What methods can you use to connect your printer to an Ethernet network? (2)

Connect your printer to an external print server device that is connected to the network. // Add an Ethernet network card to your printer

Your computer has a single hard disk with a single volume used by the C:\ drive. You have previously upgraded the disk to a dynamic disk. The disk has run out of disk space. You need to add more space to the C:\ drive?

Create a mount point using space on the second disk A mount point is an empty folder on the existing volume that points to another partition. Data saved to the folder is physically saved on the referenced partition. Extending a volume adds space to the volume. Extending a volume using space on a different disk creates a spanned volume. You cannot extend the system volume using space on a second disk. A striped volume uses two equal portions on two disks. You can create a new striped volume, but you cannot stripe an existing volume.

How many pins are on a VGA connector?

D-shaped with 15 pins

You are providing telephone support for a user who is swapping out an old CRT SVGA monitor with a new LCD SVGA monitor. He's not sure which connector on the back of the PC is used for the monitor. How would you describe the connector that he should look for?

D-shaped with 15 pins

Your motherboard has sockets for 184-pin DIMM RAM. Which type of RAM should you install?

DDR

Your motherboard has sockets for 184-pin DIMM RAM. What type of RAM should you install?

DDR-SDRAM

Your motherboard has sockets for 184-pin DIMM RAM. Which type of RAM should you install?

DDR-SDRAM

Assuming the same operting frequency, what are the advantages of DDR3 over DDR2?

DDR3 uses less power than DDR2 DDR3 doubles the data tranfer rate of DDR2

Which of the following memory ratings identifies the fastest memory?

DDR3-1600

What memory rating identifies the fastest memory?

DDR3-2000, DDR3-1600

Which service can you use on your network to automatically assign IP addresses to hosts and to help prevent the same address from being assigned to two different hosts?

DHCP You can use the Dynamic Host Configuration Protocol (DHCP) to set up a DHCP server that will assign IP addresses automatically to network hosts. DHCP servers will not assign the same IP address to two different hosts. ICMP is chiefly used by networked computers' operating systems to send error messages. The Transmission Control Protocol (TCP) is one of the core protocols of the Internet protocol suite. The Internet Group Management Protocol (IGMP) is a communications protocol used to manage the membership of Internet Protocol multicast groups

You want to implement name resolution on the Linux workstations in your company. Which protocol will you use to do this?

DNS You can use DNS name resolution for Linux workstations (as well as for most other operating systems). NetBIOS name resolution (LMHOSTS files or WINS) is typically used on Windows-based networks. The Lmhosts file is a local text file that maps Internet Protocol (IP) addresses to NetBIOS names of remote servers with which you want to communicate over the TCP/IP protocol. A WINS server address is only needed if you have older Windows clients on multiple networks. Network Time Protocol (NTP) is a means of transmitting time signals over a computer network. Simple Mail Transfer Protocol (SMTP) is used to route electronic mail through the internetwork. E-mail applications provide the interface to communicate with SMTP or mail servers.

What is the technology that protects the intellectual property rights of publishers and restricts the use of copyrighted works to those who have paid the necessary licensing fees?

DRM

Which of the following is NOT an example of wireless networking communications?

DSL

Which of the following is not an example of wireless networking communications?

DSL

Which of the following media types is not hot swappable?

DVD drive with an IDE interface

You are helping a customer over the phone who needs to connect a monitor that uses a digital interface. Which port should you instruct her to look for on the back of her PC?

DVI

You are helping a customer over the phone who needs to connect to a monitor that uses a digital interface. Which port should you instruct her to look for on the back of her PC?

DVI

Which of the following video card connectors provides digital video output?

DVI-D HDMI

One corner of the image on an SVGA monitor always has more purple tint than the rest of the image. What is the most likely problem?

Data cable

You have a computer with three hard disks. A RAID 0 volume uses space on Disk 1 and Disk 2. A RAID 1 volume uses space on Disk 2 and Disk 3. Disk 2 fails. Which of the following is true?

Data on the RAID 1 volume is accessible; data on the RAID 0 volume is not. In this scenario, Disk 2 is shared between both volumes. If disk 2 fails, the RAID 1 volume is still accessible because RAID 1 (mirrored) volumes can sustain a loss of single disk. The data on the RAID 0 volume is not accessible. RAID 0 uses striping, which distributes the data evenly between multiple disks. If a single disk fails, the entire volume is lost.

Windows 10 features a storage solution call Storage Spaces. What is the name of the Storage Spaces feature that allows to allocate space for redundant information using options that include two-way mirroring, three-way mirroring, and parity?

Data resiliency Storage spaces can include data resiliency. Choosing an option that provides resiliency requires you to allocate space for redundant information. The options for storage spaces data resiliency include: -Simple, which does not provide redundancy. This option simply adds space from the storage pool to the storage space. When you select the Simple option, all of the data in the storage space is lost if one of the drives fails. -Two-way mirror requires at least two storage devices. The data is written to two devices. Two-way mirror requires twice as much device space as the amount of storage allocated to the storage space. This option protects you from a single storage device failure. -Three-way mirror requires at least five storage devices. The data is written to the three storage devices. This option provides redundancy for the data if two storage devices fail at one time. -Parity requires that you have at least three storage devices. This option uses parity information to reconstruct data if one of the storage devices fails. Parity uses less space for redundancy than the mirror options, but performance is not as good as the mirror options if a device failure occurs. Parity requires only 50 percent more redundancy space than storage space.

Which of the following is inserted in an AMR slot to provide sound functions?

Daughterboard

How can you fix a mouse cursor and Web page that appears strange or corrupt?

Decrease your video adapter's hardware acceleration

You've noticed on your Windows workstation that sometimes your mouse cursor appears strange on the screen. In addition, images in Web pages you are viewing appear to be corrupt. How can you fix this problem?

Decrease your video adapter's hardware acceleration.

Which TCP/IP configuration parameter identifies the router that is used to reach hosts on remote networks?

Default gateway The default gateway identifies the router to which packets for remote networks are sent. The subnet mask identifies which portion of the IP address is the network address. The WINS server address identifies the WINS server that is used to resolve NetBIOS host names to IP addresses. The DNS server address identifies the DNS server that is used to resolve host names to IP Addresses. The alternate IP address identifies IP addressing information to be ised in the event the DHCP server can't be reached. The host name identifies the logical name of the local system.

You are responsible for managing client workstations for your company. A user reports that he can't send print jobs to a specif c printer. You go to the user's computer and reproduces the problem. What should you do next?

Determine if anything has changed

Which system utility would you use to troubleshoot hardware devices, examine and control the resources used by specific devices, and install updated device drivers?

Device Manager

You have a legacy non-Plug-and-Play device that must be installed under Windows. What interface do you use to manage the configuration of this device after is has been installed?

Device Manager

Which of the following input devices uses a stylus?

Digitizer

You want to configure User Account Control so that you see the permission prompt only when programs try to make changes to your computer (not when you make changes). You do not want the desktop to be dimmed when the prompt is shown. What should you do?

Disable Secure Desktop

Which tool would you use to create and delete partitions on hard drives?

Disk Management Use Disk Management to view, modify, and create partitions. Use Device Manager to update drivers and manage device-specific settings. Use the Services console to start and stop processes that run in the background. Use Explorer to view the contents of a volume, or to format a drive.

Which of the following is a command line utility that can be used to create, format, and manage partitions and volumes?

DiskPart Diskpart is the command line utility you can use to create, format, and manage partitions and volumes. Disk Management is the graphical utility you would use to do the same partition and volume creation, formatting, and management tasks you can do with DiskPart. DiskMan does not exist. Format is a command line utility used for formatting disks for use with Windows. CHKDSK is used to find and fix errors on disks, volumes, and files.

You are responsible for managing the client workstations at your computer. A user in the conference room called concerning the digital projector and display issues when the projector is connected to his laptop. After identifying the cause and completely resolving the issue, the projector displays the images perfectly both on his laptop and on the projector. What should you do next?

Document the solution

Which of the following terms describes a group of computers and users that utilize centralized resources, administration, and security settings?

Domain, Directory

What printer type is considered an impact printer?

Dot Matrix

What type of printer has the poorest print quality because the image is created using fairly large dots?

Dot Matrix

Which of the following printer types is considered an impact printer?

Dot matrix

Which type of printer uses an inked ribbon?

Dot matrix

You just installed a new video card in a user's Windows workstation. However, when you power the system on, the screen is displayed in 16 colors at 640x480 resolution. Which of the following will resolve this problem?

Download and install the latest driver from the video card manufacturer's web site

You've just installed a new video card in a employee's Windows workstation. When you power the system on and load the OS, everything on the screen looks enlarged and pixelated. You try to change the resolution, but the only available option is 640x480. Which of the following will resolve this problem?

Download and install the latest driver from the video card manufacturer's website

You have just installed a new device in your Windows 7 computer using the device's installation disc and the included drivers. After installation, the system crashes when you try to use the device. What should you do?

Download the latest driver from the manufacturer's Web site

You have just installed a new device in your Windows computer. After installation, you can't use the device. You checked in Device Manager and find that an icon for the device with a yellow exclamation mark over it. What should you do?

Download the latest driver from the manufacturer's Web site

You want to configure User Account Control so that when a UAC prompt is shown, the desktop is not dimmed, allowing you to continue working without responding to the prompt immediately. What should you do?

Edit settings in the Local Security Policy

Your computer has a sound card installed in a PCI slot. The sound card has stopped working, so you decide to use the sound card on the motherboard until you can replace the PCI sound card. You remove the card from the PCI slot. When you reboot, you have no sound and the built-in sound card does not show in Device Manager. What should you do?

Edit the CMOS settings and enable the onboard sound

You have just built a new computer running Windows. The motherboard has several built-in USB ports. You connect a device to one of these ports, but the device runs in USB 1.1 mode instead of 2.0 mode. What should you do?

Edit the CMOS settings to configure the USB ports to use USB 2.0

You have just set up a new laser printer for the company president on her Windows workstation. You have installed the printer and the drivers, what should you do next?

Edit the device specific settings

How would you configure a parallel port to use ECP mode to support custom features of a printer?

Edit the parallel port mode in the BIOS

Your new computer has a single parallel port integrated on the motherboard. You need to configure the parallel port to use ECP mode to support custom features of a printer. How do you do this?

Edit the parallel port mode in the BIOS

You have just set up a new laser printer for the company president on her Windows workstation. You have installed the printer and the drivers, what should you do next?

Edit the printer properties to configure device-specific settings

You've just set up a color laser printer on a customer's Windows workstation. You've connected it to the workstation using a USB cable and have loaded the appropriate drivers. What should you do next? (2)

Edit the printer properties to configure paper tray and other device specific settings // Verify that it is working correctly by printing a test page

A user sends a print job to a network printer and it prints page after page of random characters. He calls the help desk and a technician discovers that somehow the wrong printer driver has been loaded on the user's workstation. The technician loads the driver, verifies that the system works correctly, and documents the solution. What else should she do?

Educate the user as to how the problem was resolved and verify that they are satisfied with the results

You are attempting to boot a new system. The boot fails and the system sounds a beep code. Which of the following describe the most likely cause of this error?

Either no memory is installed or the memory was not detected

The video driver on your Windows 7 computer is preventing the system from starting up successfully. You have already downloaded an updated driver and copied it to the computer's HDD. Which mode should you select from the Windows Advanced Boot Options menu that would most likely allow you to start the computer to continue fixing the problem?

Enable VGA Mode

You use productivity apps on your iPad tablet device while traveling between client sites. You're concerned that you may lose your iPad while on the road and want to protect the data stored on it from being compromised. Currently, your iPad uses a 4-digit PIN number for a passcode. You want to use a more complex alpha-numeric passcode. You also want all data on the device to be erased if the wrong passcode is entered more than 10 consecutive times. What should you do? (select two)

Enable the Erase Data option Disable the Simple Passcode option

You have just purchased a new laptop with built-in wireless, Bluetooth, and infrared (IrDA) capabilities provided by a mini-PCIe card. When you boot into Windows, you do not see a Bluetooth adapter listed in Device Manager. What should you do?

Enabled Bluetooth in the BIOS

You provide desktop support for a small company. The company has two locations int he same city, but they are several miles away. You get a call from a user who is having problems with an application. He tries to describe what he is doing in the application, but you just can't understand what he is doing that might be causing the problem. What should you do?

Establish a Remote Assistance connection and watch what the user is doing

You provide desktop support for a small company. The company has two locations in the same city, but they are several miles away. You get a call from a user who is having problems installing a new device. You try to tell the user how to update the driver for the device over the phone, but he is having a hard time understanding your directions and is becoming frustrated.

Establish a Remote Desktop connection and update the driver

You have added two new hard disks to a Windows computer. The disks are configured as basic disks. Which of the following could be configured on these disks? (Select two.)

Extended partitions with logical drives Primary partitions Basic disks use primary and extended partitions. Each physical disk can have up to four primary partitions, or three primary partitions and one extended partition. Logical drives are defined within an extended partition. The extended partition can be divided into multiple logical drives. Dynamic disks support volumes that used discontiguous disk space. Simple volumes contain disk space from a single hard disk (both contiguous or discontiguous space). Spanned volumes use equal partition sizes on two disks to create a volume. Data is divided and saved to each disk.

You want to allow your users to download files from a server running the IP protocol. You want to protect access to the files by requiring user authentication to access specific directories on the server. Which IP protocol should you implement to provide this capability?

FTP You should implement the File Transfer Protocol (FTP). It enables file transfers and supports user authentication. The Trivial File Transfer Protocol (TFTP) also enables file transfer, but does not support user authentication. The Simple Mail Transfer Protocol (SMTP) is used to transfer email message from email clients to email servers. The Light weight Directory Access Protocol is used to access information about network resources stored in a directory server. The Secure SHell protocol (SSH) is used to securely access the console prompt of a remote computer system. The Simple Network Management Protocol (SNMP) is used to remotely monito and manage network devices and hosts.

Which of the following objects is installed between the system case and the motherboard back panel I/O ports (such as sound, video, and USB ports)

Faceplate

What is the function of the chipset on the motherboard?

Facilitate communication between the processor, memory components, and peripheral devices

You're troubleshooting a malfunctioning LED display on a notebook computer system. An external monitor correctly display the output from the notebook. Which of the following could be the cause?

Failed backlight

You're troubleshooting a malfunctioning LED display on a notebook computer system. An external monitor correctly displays the output from the notebook. Which of the following could be the cause?

Failed backlight

You have a custom database application that your company has been using for several years. The application works fine on all of your Windows XP systems. You have just purchased a new Windows 7 system for one of your sales team members. You make this user a member of the Users group on the local system. You install the custom application successfully. When the sales person logs on and tries to run the application, the program splash screen loads but then seems to hang. What should you do first?

Grant the user permissions to the directories and files used by the application.

What is a major benefit of STP over UTP

Greater resistance to interference

On a Windows system, which of the following is true of groups?

Group members have the access rights assigned to the group

Which component within a tablet device measures acceleration horizontally and vertically at the same time?

Gyroscope

Which IP protocol is used by Web browsers and Web servers to exchange files?

HTTP HTTP is used by Web browsers and Web servers to exchange files (such as Web pages) though the network. HTML is a data format that is used to create hypertext documents that can be viewed from multiple platforms. SSL secures messages being transmitted on the netwrok. SMTP is used to route electronics mail through an internetwork.

Which protocols are used on the Internet to transmit Web pages from Web servers to Web browsers running on client workstations?

HTTPS HTTP The HyperText Transfer Protocol (HTTP) is used by Web servers and browsers to transmit Web pages over the Internet. This is often confused with HTML or HyperText Markup Language, which is the markup language used to create Web content. XMLis also a markup language. SMTP is used to route electronic mail through the internetwork. E-mail applications provide the interface to communicate with SMTP or mail servers. The Network News Transfer Protocol or NNTP is an Internet application protocol used primarily for reading and posting Usenet articles.

What storage device is best suited for large storage capacity, is fast, an relatively inexpensive?

Hard disk

Which storage device uses magnetic film or aluminum platters for storing data?

Hard disk

All members of the Sales team use laptop computers while traveling to connect to the Internet. Each laptop has a built-in wireless NIC that supports 802.11b/g/n. You have trained each user to be able to create new wireless connections in order to connect to wireless networks in airports and hotels. You get a call from one user staring that her wireless connection no longer works. She has checked the wireless configuration and she knows it to be correct because other sales people at the same location are able to connect. What should you do first?

Have her verify that the wireless card's hardware switch is on the On position

After arriving in a new city today, a traveling sales team member calls you stating that his wireless connection no longer works. He has checked the wireless configuration and he knows it to be correct because it was working yesterday. What should you do first?

Have him verify that the wireless card's hardware switch is in the On position

While answering Help Desk calls, a field customer calls and complains that he cannot print to a workgroup laser printer. Which of the following should be the first question you ask?

Have you ever printed to that printer

You have four volumes on a basic hard disk. You convert the disk to dynamic. After the conversion, which of the following do you expect to see as the status of the forth volume if it is valid and has no errors?

Healthy If a basic disk gets converted to dynamic, the status of all partitions on that disk would be changed to show just Healthy. There are no Primary or Logical Partitions on a dynamic disk. A basic hard disk can have only 4 primary partitions. To get around this limitation on basic disks, the fourth partition is automatically configured as an extended partition that can hold logical drives. So, the fourth partition would show a status of Healthy (Logical Drive).

You have four volumes on a basic hard disk. Which of the following do you expect to see as the status of the forth volume if it is valid and has no errors?

Healthy (Logical Drive) A basic hard disk can have only 4 primary partitions. To get around this limitation on basic disks, the fourth partition is automatically configured as an extended partition that can hold logical drives. So, the fourth partition would show a status of Healthy (Logical Drive). The first three partitions would show a status of Healthy (Primary Partition). If the disk had been a dynamic disk the status would just be Healthy. If the disk gets converted from basic to dynamic, the status would be changed to show just Healthy.

A user calls t report a problem. She is trying to install an application on her new Windows 10 system, but cannot. Her user account is a member of the Users group on the system. What do you suspect is causing the installation issue?

Her group membership does not allow her to install new software

Which of the following correctly describe the most common format for expressing IPv6 address?

Hexadecimal numbers 32 numbers, grouped using colons

Which device has the highest priority on the SCSI bus?

Host adapter

Your desktop workstation system uses a SCSI bus to connect storage devices. The SCSI host adapter is assigned an ID of 7, the SCSI HDD is assigned an ID of 5, the SCSI tape drive is assigned an ID of 3, and the SCSI DVD drive is assigned an ID of 0. Which device has the highest priority on the SCSI bus?

Host adapter

Which of the following terms describes a PC card that you can insert and remove without rebooting the computer?

Hot-swappable

Which of the following terms describes a Windows operating system patch that corrects a specific problem and is released on a short-term, periodic basis?

Hotfix

Which feature on Intel chips allows a single processor to run two threads in parallel, instead of processing single threads linearly?

Hyper-threading

What standard provides data transfer rates up to 800Mbps with a maximum cable length of 100 meters?

IEEE 1394b

Which of the following standards provides for data transfer rates up to 800 Mbps with a max cable length of 100 meters?

IEEE 1394b

Why is it important to have your mobile device charger plugged in while it is receiving an operating system update?

If the battery dies during the update, the operating system could become corrupted

Which statement is true regarding IDE master and slave settings?

If two IDE devices share the same channel, one device must be set to master and the other must be set to slave

You are updating the operating system on your iPad. Your iPad is connected to your computer and you are using iTunes to install the update. What would happen to your iPad if you disconnect it before the operating system update is complete?

If you disconnect during the update, the operating system could become corrupted.

You have been asked to recommend a printer that will be used in a travel agency. The printer will be used to print airline tickets. Each ticket has 4 pages, and the same information must show up on all four pages with a single pass of the printer. Which printer type would you recommend?

Impact

You have been asked to recommend a printer that will be used in a travel agency. The printer will be used to print airline tickets. Each ticket has four pages (multi-part, carbon based forms), and the same information must show up on all four pages with a single pass of the printer. Which printer type would you recommend?

Impact

How would you view a list of all IRQs and the device using each IRQ?

In Device Manager, click View>Resources by type

You want to make a printer on a Windows workstation available only between certain hours. Which path would you use to edit this setting?

In Devices and Printers, right click the printer object and select Printer Properties. Use the Advance tab.

You want to configure Power Plans on your Windows 7 laptop computer. Which of the following can do this?

In the Notification Area, double-click the battery icon. Click More Power Options. Go the Control Panel - System and Security - Power Options

A user reports that he can't browse to a specific Web site on the Internet. From his computer, you find that a ping test to the Web server succeeds. A trace route test shows 17 hops to the destination Web server. What is the most likely cause of the problem?

Incorrect DNS server address

The display is using strange colors. Which of the following is a solution to this problem?

Increase the color depth

What is the solution to display using strange colors?

Increase the color depth

Your CRT monitor flickers. What should you do?

Increase the refresh rate

Which of the following is NOT an advantage of SSDs over HDDs?

Inexpensive

You have purchased new components to build a new computer. While assembling the computer, you notice that the motherboard faceplate doesn't have any parallel ports. You need these ports to support some devices that you need to use with the computer. You check the motherboard documentation and find that parallel ports are not included on the motherboard. Which of the following would be the cheapest solution?

Install a PCI card to provide the necessary ports

A manager wants you to install a Serial ATA HDD into his computer, but the motherboard does not have a Serial ATA connector. What should you do?

Install a Serial ATA host adapter in an expansion slot

What should you do if the motherboard does not have a Serial ATA connector?

Install a Serial ATA host adapter in an expansion slot

You're troubleshooting an older laser printer that is creating 'accordion jams' where the paper is crumpled as it exits the printer moving into the output tray. What can you do to fix this problem?

Install a maintenance kit

Youre troubleshooting an older laser printer that is creating "accordion jams" where the paper is crumpled as it exits the printer moving into the output tray. What can you do to fix this problem?

Install a maintenance kit

You want to create a RAIDS array using three newly-installed SATA disks.

Install an add-on RAID controller

Your computer currently runs Windows 7 Enterprise edition. You want to create a RAID 10 array using four newly-installed SATA disks. When you go to Disk Management, the option to create the RAID 10 array is not available. What should you do?

Install an add-on RAID controller

Your computer currently runs Windows 7 Enterprise edition. You want to create a RAID5 array using three newly-installed SATA disks. When you go to Disk Management, the option to create the RAID5 array is not available. What should you do?

Install an add-on RAID controller

Your computer currently runs Windows 7 Enterprise edition. You want to create a RAID 5 array using three new-installed SATA disks. When you go to Disk Management, the option to create the RAID 5 array is not available. What should you do?

Install an add-on RAID controller. Windows 7 desktop operating system support creating RAID 0 and RAID 1 arrays Disk Management, but do not support configuring RAID 5. To use RAID 5 on a client computer, you will need to use a RAID controller installed in an expansion slot or integrated in the motherboard.

You are setting up a small network in your office with one Windows server and 50 Windows workstations. You want to spend as little as possible configuring the workstations with IP addressing information. What should you do?

Install the DHCP service on your server. The DHCP protocol allows you to assign IP addresses automatically. In this scenario, you should configure the DHCP service to rin on the network server. The DHCP client on each workstation can then contact the DHCP server when the workstations connect to the network to be automatically assigned IP addressing information. You could instruct each user to manually enter IP addressing information but there is a higher change of error and will likely require more administrative overhead.

You have a computer with a dual core 64-bit processor that uses the x86-x64 instruction set. You want to install the 32-bit version of Windows Vista on the computer. What should you do?

Install the OS normally

You have a computer with a dual core 64-bit processor that uses the x86-x64 instruction set. You want to install the 32-bit application on the computer. What should you do?

Install the application normally

Which of the following is the correct order for installation of a new USB device and the driver files that shipped with it?

Install the device driver using the manufacturer's installation instructions. Attach the device. Complete the Add a Device wizard when it pops up

How do you set the floppy drive to A: drive?

Install the drive after the twist in the ribbon cable

You have an existing computer running Windows 7 Enterprise. You want to configure a RAID 1 array in the computer. You install two new SATA drives, then use the RAID controller integrated in the motherboard to define a RAID 1 array using them. When you boot the computer, Windows does not show the logical RAID drive. What should you do?

Install the drivers for the RAID controller

You have an existing computer running Windows 7 Enterprise. You want to configure a RAID1 array in the computer. You install two new SATA drives, then use the RAID controller integrated in the motherboard to define a RAID1 array using them. When you boot the computer, Windows does not show the logical RAID drive. What should you do?

Install the drivers for the RAID controller

You have an existing computer running Windows & Enterprise. You want to configure a RAID 1 array in the computer. You install two new SATA drives, then use the RAID controller integrated in the motherboard to define a RAID 1 array using them. When you boot the computer, Windows does not show the logical RAID drive. What should you do?

Install the drivers for the RAID controller. You must install the RAID driver so that Windows recognizes arrays created by the mother board RAID utility. Without the driver, Windows will not be able to see the logical drive defined by the array. When you define the array, you configure the BIOS to use RAID as the SATA type. If you had not completed this step, you would not be able to run the RAID configuration utility. Use AHCI to configure SATA drives to support hot-swapping.

You need to connect a new USB scanner to the USB port on your computer. What should you do?

Install the scanner drivers, then connect the scanner to the USB port

Don is an accountant in the Finance department. For the last several months he has been testing an online accounting program. After speaking with his manager, don received permission to download a streamlined version of the software which requires a local installation. after downloading, Don tried to install the application, but the operating system will not allow it. Out of frustration, he called the Help Desk. The Help Desk personnel came to Don's machine and installed the application without issue. Which of the following is the most likely reason Don could not install the application?

Insufficient permissions

Which of the following statements accurately describes how a modem works?

It demodulates analog data from a telephone network into digital PC data

Which of the following is true of the Guest user account on a Windows system?

It is disabled by default.

Which device will allow you to set up one keyboard, one monitor, and one mouse for all three computers?

KVM

You have three computers in your office. You would like to reduce the time it takes to move from one computer to the next, and you would like to use only one keyboard, monitor and mouse for all three computers. Which device allows this type of setup?

KVM

You are putting together a gaming system and need to make sure you get a display that meets your needs. The display needs to have a very good response time, and you would prefer that it be affordable and power efficient

LCD display with TN panel

What is true of LED monitors?

LED monitors use LED backlight technology

What type of printer uses a drum, plastic toner, and fuser to create a printed page?

Laser

Which type of printer uses lasers and electrical charges to transfer images to paper?

Laser

You are configuring a new system and want to use a RAID 0 array for the OS using SATA disks and the RAID functionality built into the motherboard. Which of the following actions will you take as part of the configuration?

Load the RAID drivers during the OS installation

Which of the following will improve the security of sensitive information on your device if it is lost or stolen?

Locator applications Remote wipe A screen lock

Which of the following are steps you can take to avoid having your mobile device exploited by a hacker or infected by a virus?

Lock the screen with some form of authentication Keep the operating system up to date

Which of the following is an advantage to purchasing a computer with video and audio integrated onto the motherboard?

Lower overall system cost

What is a DB-15 connector on a sound card typically used for?

MIDI port Joystick

One of the programs that launches automatically at startup is causing your Windows workstation to lock up. You have examined the Startup folder, and the problem application is not present. Which utility should you use to prevent the program from starting automatically?

MSConfig.exe

After installing two memory modules, you power on the system to check for errors. You find that the BIOS program recognizes only one of the memory modules. What should you do first?

Make sure that both modules are seated properly in their slots

You have just finished upgrading the 250 W power supply in your desktop computer to a 450 W power supply. Now the BIOS doesn't recognize one of the HDDs in the system during post. What should you do?

Make sure that the HDD is connected to the power supply

A user complains that his notebook display has started to go dim intermittently. You suspect the backlight might need to be replaced but you want verify that the backlight is failing before you replace it. What should you check before replacing the backlight?

Make sure that the dimming isn't being cause by a power saving method that has been configured to conserve notebook power.

A user complains that his notebook display has started to go dim intermittently. you suspect the backlight might need to be replaced but you want verify that the backlight is failing before you replace it. What should you check before replacing the backlight?

Make sure that the dimming isn't being cause by a power saving method that has been configured to conserve notebook power.

A panicked user comes to you at the support desk and asks you to come to his office because his notebook has no power. He's positive that his battery has completely failed because he came in this morning and there is no power at all to his laptop. He left it plugged in on his desk all night but it will not turn on. He has an important presentation to make in a couple of hours and insists that you bring a replacement battery. What troubleshooting steps should you do before replacing the battery.

Make sure the AC cord is securely plugged into both the wall outlet and the power adapter Make sure the DC cord from the power adapter is plugged firmly into the notebook power connector.

What should you do when the DVD drive won't work?

Make sure the DVD drive cables are connected

You have just finished installing a new hard disk in your computer. Now the DVD drive won't work. What should you do first?

Make sure the DVD drive cables are connected

What should you do if a USB device does not work after you install the driver?

Make sure the USB device is plugged in properly

You are trying to connect a new USB device to your computer. You install the driver, then connect the device to an open USB port. The device does not work. What should you do first?

Make sure the USB device is plugged in properly

You recently upgraded the processor in your laptop computer to a faster processor. The computer runs, but after using it for several minutes, it shuts down unexpectedly. Which of the following should you do first?

Make sure the case fans are plugged in

What should you when the hard disk will not work?

Make sure the power connectors on the hard disk are plugged in all of the way

If a notebook computer with an integrated wireless network adapter shows that there is no wireless network connection, what should you check first?

Make sure the switch that turns the wireless network card on and off is in the on position.

A customer needs to use several applications. Currently, the computer cannot keep all the necessary applications open at the same time. Which of the following components should you consider upgrading?

Memory

You have a network that uses a logical bus topology. How do messages travel through the network?

Messages are broadcast to all devices connected to the network.

Which port should you use to connect a non-amplified microphone to a sound card?

Mic In

You want to build a new desktop that is portable that you can easily take to your friends' house for gaming parties. Which of the following form factors would you likely select?

Micro-ATX

You have an executive user who keeps sensitive information about the company on a company-owned mobile device. You want to be prepared to keep company information secure if he loses this device or if it gets stolen.

Mobile device management software that performs remote wipes Mobile device management software that does full device encryption

How should you fix a monitor that displays a large black border around the main screen image?

Monitor hardware controls

Your monitor displays a large black border around the main screen image. Where should you go to fix this problem?

Monitor hardware controls

You have a desktop PC that you have been using for 3 years in the United States. You are going on a study-abroad program for one semester and want to take your computer with you. After some research, you find that the country where you will be staying uses different voltage than what is used in the United States. What should you do so that the computer can be compatible with the electrical power in Europe?

Move the switch on the power supply to a different voltage

Which tool can you use to view (but not modify) hardware and configuration information for your computer?

Msinfo32

Which of the following refers to placing two processors on a single processor chip or die?

Multi-core

Which feature allows a tablet to recognize multiple finger touches at the same time?

Multi-touch

Which tool would you use to measure electrical properties such as voltage, amps, and resistance?

Multimeter

Which of the following is a characteristic of a multi-processor system?

Multiple processor sockets on the motherboard

What is an advantage of connecting a printer to a network?

Multiple users can print to the same printer

Which of the following is a mobile technology that can be used to store and transmit encrypted information for purposes such as making payments from a mobile device?

NFC chips

Which of the following form factors does not have expansion card slots on the motherboard but rather uses a riser card for expansion cards?

NLX

What is required to control access to the file system using file and folder permissions on a Windows-based computer?

NTFS-formatted partition

What is required to control access to the file system using file and folder permissions on a Windows-based computer?

NTFS-fromatted partition File permissions are only available under Windwos for files on a partition formatted with NTFS, not FAT32. The Encrypting File Service (EFS) with Windows ecrypts individual files. The Ext4 file system is used on Linux systems.

You have booted your Windows 7 workstation into Safe Mode and enabled Boot Logging. To which log file is the boot logging information now being written?

NTbtlog.txt

Which of the following protocols is non-routable and requires another protocol to enable internetwork communications?

NetBIOS

Which utility would you use to view current connections and active sessions and ports on a computer?

Netstat

Which tool would you use in Windows Vista/& to manage network connections?

Network and Sharing Center Use the Network and Sharing Center in Windows Vista/7 to view and manage network connections. My Network Places is in Windows XP, and Network Neighborhood is in Windows 98. Use Internet Options to configure Internet and Internet Explorer settings.

Which of the following battery types has the greatest need to be completely drained before being recharged?

Nickel Cadmium

Which of the following battery types has the greatest need to be completely drained before being recharged?

Nickel Cadmium (Ni-Cad)

You have a DVD-Rom disc with no label and you want to know if it has any important files on it. You inset the DVD-ROM into your optical media drive, then you double-click the drive letter for the optical drive to see the contents of the disk. If the DVD-ROM is not a valid disc, which error message will you see?

No Media The No Media status for an optical or removable media drive that does not contain a valid disc. A Foreign disk is a dynamic disk that was created in one system and moved to another system. The Unreadable status indicates a hardware failure, I/O errors, or other corruption but might also be caused by a delay in reading the disk in Disk Management. The Missing status shows when a dynamic disk has failed.

You have a disk in your system that is displayed in the Disk Management utility as shown in the image below. The disk icon includes a red arrow that it pointing down. Which of the following would you expect to see, in the space when the re outline is, as the status of this disk?

Not Initialized When Disk Management shows a disk icon that includes a red arrow that is pointing down, it indicates that the disk is Not Initialized.

You are testing the power supply in a PC system by measuring the voltage available on the 4-pin Molex connector. The voltage on the red wire is +5.1 volts. What should you do?

Nothing, the power supply is working normally

Device manufactures are constantly finding bugs, vulnerabilities, or better ways for their devices to communicate with the operating system. Because of this, what should you do before you install a new device?

Obtain the latest driver from the manufacturer's website before installing the device

Device manufactures are constantly finding bugs, vulnerabilities, or better way for their devices to communicate with the operating system. Because of this, what should you do before you install a new device?

Obtain the latest driver from the manufacturer's website before installing the device.

You use a laptop running Windows that has a single type III PCMIA slot. You have started Windows and have been using a Firewire card in the PCMIA slot. Now you want to remove the Firewire card and replace it with an 802.11n wireless NIC that uses the PCMIA slot. How should you make the change?

On the System Tray, double-click the Safely Remove Hardware icon. Shut down the Firewire card, then remove it. Insert the NIC

You have a computer with a single hard disk configured as a basic disk with a single partition formatted with NTFS. The computer runs Windows 7 Enterprise. The disk has run out of space. You need to add space to the disk. You install a new hard drive start Disk Management. Which of the following is a required task to add space to the existing volume?

On the new hard disk, create a new partition without a drive letter. Because this is the system volume, the only way to add space to the volume using space on the new disk is to create a mount point. A mount point is an empty folder on the existing volume that points to another partition. Data saved to the folder is physically saved on the referenced partition. To create a mount point: -Create an empty folder on the existing volume. -Create a partition on the new disk without a drive letter. -Mount the partition to the empty folder on the existing volume. You cannot extend the volume to another disk because the volume is the system volume. You cannot extend the system volume even if it is on a dynamic disk. You can create mount points on basic or dynamic volumes.

You have a workstation running Windows 7, 64-bot edition. A local printer connected to a USB port is shared so that other users can print to that printer. Users running the 32-bit versions of Windows report that they can't install the driver for the shared printer. Users running 64-bit versions of Windows do not have any problems. What would you do to fix the problem? (2)

On your computer, add the x86 drivers// Manually install the correct driver on each computer that is having a problem

One software license model allows software to be freely distributed, downloaded, and installed without paying a license fee, but often requires a fee for support, training, or added functionality. What is the name of this model?

Open Source

You would like to upgrade the processor in your system to a 64-bit processor. Which of the components will you most likely need to upgrade as well to take full advantage of the new processor?

Operating System

Which of the following components can be updated by the Windows Update service?

Operating system and critical driver files.

Which of the following expansion buses are most commonly used for video cards in modern computer systems?

PCI Express

What expansion bus is best for high-speed, high-res, 3D graphics?

PCIe

Which expansion bus is best for high-speed, high-resolution, three-dimensional graphics?

PCIe

What are 3 printer languages?

PCL // Escape Codes // PostScript

Which of the following protocols do e-mail clients use to download messages from a remote mail server?

POP3

Which of the following protocols do e-mail clients use to download messages from a remote mail server?

POP3 The POP3 protocol is part of the IP protocol suite and used to retrieve e-mail from a remote server to a local client over a network connection. SNMP is a protocol used to monitor network traffic. SMTP is an IP protocol used to send e-mail. FTP is used to transfer files.

What is the name for the routine that tests the motherboard, memory, disk controllers, video, keyboard and other system hardware?

POST

What is the name for the routine that tests the motherboard, memory, disk controllers, video, keyboard, and other system hardware?

POST

What type of printer connection would connect to LPT:1?

Parallel

What uses Centronics-type connectors?

Parallel

Which of the following types of printer connections would connect to LPT:1?

Parallel

Which of the following use Centronics-type connectors?

Parallel

A D-shaped 25-pin female port on the back of a computer is a:

Parallel port

A D-shaped, 25-pin female port on the back of a computer is a:

Parallel port

What is an advantage of parallel ports over serial ports?

Parallel ports have higher data transfer rates

Which of the following is an advantage of parallel ports over serial ports?

Parallel ports have higher data transfer rates

Which of the following is an error detection technique that can detect errors with only ONE bit?

Parity

Several employees have forwarded you an e-mail indicating that your company's health insurance provider has just launched a new benefits management Web site that all employees must start using. The employees are told in the e-mail to click a link to access the site. Once there, they are required to provide their SSN. However, you have discovered that your company's insurance provider did not send this e-mail. What kind of attack just occurred?

Phishing

You recently purchased a USB audio headset and connected it to a USB port on your Windows system. However, when you launch you music player, the audio is played through your desktop speakers instead of the new USB headset. You need to reconfigure the system to use the headset instead of the desktop speakers. Click the tab you would use in the Sound Properties window to do this.

Playback

You're troubleshooting a malfunctioning notebook computer. Nothing appears on the LCD display when the system is powered on. What is the first thing you should do?

Plug in an external monitor

You're troubleshooting a malfunctioning notebook computer. Nothing appears on the LED display when the system is powered on. What is the first thing you should do?

Plug in an external monitor

Which of the following is an extra button or knot on a laptop keyboard that moves the mouse cursor?

Point stick

While using a new windows system, you find that the mouse pointer tracks much more slowly on the screen than you would prefer. You want to increase the mouse pointer speed. click the tab you would use in the Mouse Properties window to do this.

Pointer Options

Match the port numbers on the left with the protocols associated with them on the right

Port 22 - Secure Shell (SSH) Port 548 - Apple Filling Protocol (AFP) Port 443 - HTTP over SSL (HTTPS) Port 80 - Hypertext Transfer Protocol (HTTP) Port 445 - Server Message Block (SMB/CIFS) directly over TCP Port 427 - Service Location Protocol (SLP) Port 143 - Internet Message Access Protocol (IMAP)

Which of the following devices can be used to distribute electrical power along with network data on twisted-pair Ethernet cabling (CAT 5 or higher)

Power over Ethernet

Which of the following components converts AC to DC?

Power supply

Which of the following tools is specifically designed to test the DC voltage on a HDD power connector?

Power supply tester

A user needs to use her laptop to give a presentation using a video projector. She called asking you how to switch the display to the external port on her laptop. What should you tell her?

Press the Fn key along the function key on the notebook keyboard with a monitor on it

Which component in a laser printer prepares the photosensitive drum for writing by causing it to receive a negative electrostatic charge?

Primary Corona

You are in the process of building a new computer. You would like to configure your computer to use Crossfire to improve performance when playing your favorite game. Which of the following will be part of the configuration process?

Purchase two identical video cards

Due to a blackout, power is no longer coming from the wall outlet and your computer is now off. You do not have a UPS and you need to remove a disc out of the DVD drive. What is the easiest method to retrieving the disk?

Push an unbent paper clip into the hole on the front of the drive

What is the easiest method for retrieving the disc?

Push an unbent power clip into the hole on the front of the drive

What RAID configuration level provides increased performance using only two disks?

RAID 0

What drive configuration uses striping without fault tolerance?

RAID 0

Which RAID configuration level provides increased performance using only two disks?

RAID 0

Which of the following drive configurations uses striping without fault tolerance?

RAID 0

Which RAID configuration level provides increased performance using only two disks?

RAID 0 RAID 0 (striping) uses two or more disks and provides an increase in performance but not fault tolerance. RAID 1 (mirroring) uses two disks to provide fault tolerance but not an increase in performance. RAID 5 uses a minimum of three disks and provides both fault tolerance and an increase in performance.

Which drive configurations uses stripping fault tolerance?

RAID 0. RAID 0 uses disk stripping and offers no fault tolerance. DISK striping breaks data into units and stores the units across a series of disks by reading and writing to all disks simultaneously. A failure of one disk in the set means all data is lost. This is the fastest of all RAID types. RAID 5 a;so uses disk striping

What is the advantage of RAID 5 over RAID 1?

RAID 5 improves performance over RAID 1

What is an advantage of RAID 5 over RAID 1?

RAID 5 improves performance over RAID 1. Explanation Raid 5 provides both *fault tolerance and improved performance. RAID 1 (mirroring) provides only *fault tolerance with no performance benefit. Both RAID 5 RAID 1 can only sustain a loss of one disk in the set. User multiple disk controllers to provide redundancy for the disk controller. *Fault tolerance is the property that enables a system to continue operating properly in the event of the failure of (or one or more faults within) some of its components.

What is an advantage of RAID 5 over RAID 1?

RAID 5 improves performance over RAID1

Which of the following drive configurations uses striping with parity for fault tolerance?

RAID 5. RAID 5 also uses disk striping, but provides fault tolerance for a dingle disk failure. Disk striping breaks data into units and stores the units across a series of disks by reading and writing to all disks simultaneously. RAID 0 uses disk striping and offers no fault tolerance. A failure of one disk in the set means all data is lost. RAID 1 provides fault tolerance but does not use stripping. A RAID 10 array nests a mirrored array within a striped array.

Which RAM standard requires heat spreaders?

RAMBUS

Which of the following are used to connect a cable modem to the Internet connection

RG-6 coaxial cable F-type connectors

Which kind of connector do you use to connect a modem to a standard telephone line?

RJ-11

Which of the following requires that either all memory slots are populated with memory modules or a continuity module?

Rambus

Your're troubleshooting a notebook system that uses a digitizer pad and stylus for user input. The user has complained that the digitizer pad registers stylus taps about 1 inch to the right of where the tap actually occurred. How can you fix this problem?

Re calibrate the digitizer pad

You have a computer system with a Pentium IV processor that operates at 2 GHz. You would like to upgrade to a faster processor, but you don't want to replace the motherboard. Which of the following should you do first?

Read the motherboard documentation to identify which processors are supported

You have a computer system with a dual-core processor. You would like to upgrade to a quad-core processor, but you don't want to replace the motherboard. Which of the following should you do first?

Read the motherboard documentation to identify which processors are supported

Rodney, a user in the research department, reports that he is getting STOP errors while using his Windows XP computer. You ask Rodney if anything has changed recently on the computer. Rodney explains that he ran the installation program for his PDA and everything worked fine until he tried to hot sync. Now any time he hot syncs, he has to reboot the computer. You need to fix Rodney's computer and prevent Rodney from using the PDA until you can install an update driver. What should you do?

Reboot the system in Safe Mode. Disable the PDA's driver in Device Manager

While working on your Windows 7 system, the system encounters a critical error. For a brief second you see the Blue Screen indicating the error. Before you can read the error, however, the system reboots. After rebooting and logging back on, the same thing happens again. What should you do so that you can read the error message next time it happens without the system rebooting?

Reboot the system, Press F8 and disable the automatic restart feature

While using the touchpad, you notice than the mouse is not responding very well, making it difficult to correctly move the mouse around the screen. How can you fix this problem?

Recalibrate the touchpad

You recently replaced a malfunctioning video card on your laptop. After reassembling the laptop, everything works well except for the wireless network connection. The wireless adapter functioned correctly before you replaced the video card. What would most likely resolve this problem?

Reconnect the antenna connections

You recently replaced a malfunctioning video card on your laptop. After reassembling the laptop, everything works well except for the wireless network connection. The wireless adapter functioned correctly before you replaced the video card. What would most likely resolved this problem?

Reconnect the antenna connections

You recently replaced a malfunctioning video card on your laptop. After reassembling the laptop, everything works well except for the wireless network connection. The wireless adapter functioned correctly before you replace the video card. What would you likely resolved this problem?

Reconnect the antenna connections in the bezel

You recently purchased a USB audio headset and connected it to a USB port on your Windows system. The headset includes a microphone that can be used to record audio. However, when you launch your audio recording program, no audio is recorded. You need to reconfigure the system to use the headset mic instead of the built-in mic. click the tab you would use in the Sound Properties window to do this.

Recording

You have been using the same computer for several years. To improve performance, you decide to upgrade the processor. You check the motherboard documentation and purchase the fastest processor supported by the motherboard. However, when you try to start the computer it beeps regularly and nothing is displayed on the screen

Reinstall the old processor in the motherboard Flash the UEFI firmware

Which of the following remote access mechanisms on a Windows system lets you watch what a user is doing and, if necessary, take control of the user's desktop to perform configuration tasks?

Remote Assistance

Your laptop carrying case is designed from a 15-inch laptop, yet you think you can squeeze your 16-inch laptop into it. Before slipping the laptop into the case, what should you do first?

Remove any ExpressCards from their slots

Your manager has been using the same laptop computer without error for four years. Suddenly, the computer will not start and run correctly. What should you do to isolate the problem?

Remove the batteries and attempt to run the computer from a wall outlet

You have a system that has been overheating. Which of the following actions WILL NOT help to keep the system cool?

Removing the computer case

Which of the following actions is not recommended for keeping your system cool?

Removing unused expansion card slot covers

Your computer has one single core processor installed. The motherboard supports processors with up to four cores. You want to upgrade your computer to a dual-core system. Which of the following will by part of your configuration?

Replace the existing processor

You are testing the power supply in a PC system by measuring the voltage available on the 4-pin Molex connector. The voltage on the yellow wire is +10.1 volts. What should you do?

Replace the power supply

To test a power supply, you use a multimeter to measure the voltage on a Molex hard disk drive connector. You note that the yellow wire in the connector provides 10 volts DC. What should you do?

Replace the power supply. It is failing

You test adding a second CPU. You remove the terminating resistor from the second CPU slot, insert the CPU and perform your testing. Upon conclusion of the test you remove the second CPU and find that your system no longer boots up properly? How can you correct this situation?

Replace the terminating resistor in the slot that was occupied by the second CPU

What method does an MMC card use for storing data?

Reprogrammable memory

What method does an SDHC card use for storing data?

Reprogrammable memory

Windows 10 features a storage solution called Storage Spaces. When you configure Storage Spaces you can include information redundancy with a feature called data resiliency. Match the types of data resiliency on the left with the appropriate descriptions on the right. Each type of data resiliency may be used once, more than once, or not at all.

Requires that you have at least three storage devices - Parity Requires at least five storage devices - Three-way mirror Does not provide redundancy - Simple Protects you from a single storage device failure - Two-way mirror Requires at least two storage devices - Two-way mirror Allows you to reconstruct data if one of the storage devices fails - Parity Protects your data if two storage devices fail at one time - Three-way mirror Storage spaces can include data resiliency. Choosing an option that provides resiliency requires you to allocate space for redundant information. The options for storage spaces data resiliency include: -Simple, which does not provide redundancy. This option simply adds space from the storage pool to the storage space. When you select the Simple option, all of the data in the storage space is lost if one of the drives fails. -Two-way mirror requires at least two storage devices. The data is written to two devices. Two-way mirror requires twice as much device space as the amount of storage allocated to the storage space. This option protects you from a single storage device failure. -Three-way mirror requires at least five storage devices. The data is written to the three storage devices. This option provides redundancy for the data if two storage devices fail at one time. -Parity requires that you have at least three storage devices. This option uses parity information to reconstruct data if one of the storage devices fails. Parity uses less space for redundancy than the mirror options, but performance is not as good as the mirror options if a device failure occurs. Parity requires only 50 percent more redundancy space than storage space.

You have just installed a maintenance kit in your laser printer. What should you do next?

Reset the page count

On a Windows 10, using Storage Spaces eliminates the need for which of the following tasks? (Select two.)

Resizing volumes Repartitioning drives Storage spaces eliminates the need for such tasks as: -Repartitioning drives -Resizing volumes -Backing up data in order to repartition

A user installs a new graphics application on her Windows system. During the installation process, the application prompts the user to load a custom video driver that has been optimized for the application. She does so and then completes the installation. Several days later, the user reports that her display doesn't seem to be working properly under some conditions. To fix the problem, you need to reload the old video driver. How could you accomplish this?

Revert the system to a restore point prior to installing the video driver User Device manager to roll back the video driver

An internal laptop keyboard is generally connected to the laptop's system board using a:

Ribbon cable

For a special project, you have been asked to recommend the lowest profile desktop computers available. You are attempting to put together the specs for these machines. Which of the following types of cards are attached to the motherboard to allow expansion cards to plug into them instead of the motherboard?

Riser

Uses the IP address within a packet to move packets between networks

Router

You have just installed a new hardware device, upgraded the driver, and installed the custom software that came with the device. Now you can't get the device to work. What should you do first?

Run any diagnostic software that came with the device

You have a Windows Vista computer that was recently upgraded from Windows XP. One application worked fine in Windows XP, but now does not run in Windows Vista. You have checked the application vendor's Web site but there is no update available. What should you try next to run the application?

Run the application in Compatibility mode

You manage Windows desktops for your organization. You recently updated all of your workstations to Windows 10. Your organization relies on a particular application, which worked correctly in earlier versions of Windows, but now does not run in Windows 10. You have checked the application vendor's website, but there is no update available. What should you try next to run the application?

Run the application in compatibility mode. Create a virtual machine that runs an older version of Windows. Run the application within the virtual machine.

You want to purchase a motherboard that has integrated sounds with digital audio output. Which port would you likely find on the motherboard faceplate that indicates digital audio support

S/PDIF

What interface is primarily used for internal hard drives in modern desktop PC systems?

SATA

What is the most common disk interface used for optical drives on home and office computers?

SATA

Which interface is primarily used for internal HDDs in modern desktop PC systems?

SATA

Which of the following is the most common disk interface used for optical drives on home and office computers?

SATA

Which type of interface is most commonly used for internal HDDs in notebook systems?

SATA

Which generation of SATA storage devices does the following? Supports up to 6 Gbps data transfer rates Addresses solid state drives

SATA3

Which of the following network services or protocols uses TCP/IP port 22?

SSH

Which of the following tools allow for remote management of severs?

SSH Telnet

The video driver on your Windows 7 computer is preventing the system from starting up successfully. You have already downloaded an updated driver and copied it to the computer's HDD. Which mode should you select from the Windows Advanced Boot Options menu to ensure that the system can complete the boot process?

Safe Mode

What is the role of the CMOS in a modern computer?

Saves information about system devices

You're troubleshooting a computer running Windows 7. The OS has halted and a blue screen has been displayed on the monitor with an error message. What is the first step you should take in troubleshooting the issue?

Search for the error in Microsoft's knowledgebase or in a search engine on the Internet

Which component in a laser printer charges the paper to attract toner?

Secondary corona

What is the purpose of the small cable that connects an IDE optical drive to the sound card?

Sends CD audio from the optical drive to the sound card

What is an advantage of serial ports over parallel ports?

Serial ports can send data over longer distances

Which of the following is an advantage of serial ports over parallel ports?

Serial ports can send data over longer distances

One device is newer and faster than the other. Which device should you set to master?

Set the newer, faster device to master

Two IDE devices share the same channel. One device is newer and faster. Which device should you set to master?

Set the newer, faster device to master

You recently upgraded a client's older workstations from Windows XP to Windows 7. The client has called to complain that the interface is very slow. For example, after clicking on the Start button, the Start Menu slowly appears on the screen. How can you fix this problem without upgrading the hardware itself?

Set the visual effects for best performance

A user is trying to log into Windows on her notebook computer. She enters the correct password for her user account, but the system won't let her authenticate, claiming the wrong password has been entered. What's causing the problem?

She has turned Num Lock on causing numbers to be sent from keyboard instead of letters

A user is trying to log into Windows on her notebook computer. She enters the correct password for her user account, but the system won't let her authenticate, claiming the wrong password has been entered. What's causing the problem?

She has turned Num Lock on causing numbers to be sent from the keyboard instead of letters

You want to set up a Windows system to also be able to boot to Linux. To be able to dual boot, the system needs a partition on which to install Linux. You don't have an extra hard disk that can be used for the Linux partition. The existing disk has unpartitioned space available, but it has about 300 GB of free space. Which disk management operation can you perform on the disk to use some of the free space for the Linux partition?

Shrink the primary partition You can decrease the space used by primary partitions and logical drives by shrinking them into adjacent, contiguous space on the same disk. For example, if you discover that you need an an additional partition but do not have additional disks, you can shrink the existing partition from the end of the volume to create new unallocated space that can then be used for a new partition.

After arriving early this morning, you turn off your computer to begin your work. Instantly you see smoke and smell a strange odor coming from the computer. What should you do?

Shut off the system immediately

What optical media has the greatest storage capacity?

Single-layer, single-sided Blu-ray disc

Which optical media has the greatest storage capacity?

Single-layer, single-sided Blu-ray disc.

Which of the following statements is true regarding single- and double-sided memory?

Single-sided memory uses half the number of memory modules as double-sides memory of the same capacity

You recently installed several applications on a Windows system. After doing so, you notice that the system takes much longer to boot up. You suspect that the new applications include one or more helper applications that are automatically loaded when the system boots. To increase performance, you want to identify any such helper applications and disable them. Click on the tab in Task Manager that you would use to do this.

Startup

You have a host on your network that provides a service that requires the server to always use a specific IP address. Which IP addressing method can you use to manually assign the specific IP address?

Static IP Addressing With static IP addressing, you manually assign all configuration values. Static addressing is prone to error and should only be used under the following conditions: -The network has a small number of hosts. -The network will not change or grow. -You have hosts that must always use the same IP address.

Which of the following LAN devices receives a signal on one port, and forwards that signal only to the port where the destination device is connected?

Switch

Commit Charge

The amount of memory that has been assigned to running process.

Disk Time

The amount of time that the disk subsystem is busy reading from and writing to disk.

Processor utilization

The amount of time the processor spends performing non-idle tasks.

You are servicing a client's computer that has been randomly restarting. You decide t test the power supply using a multimeter. You connect the positive lead to the yellow wire on one of the Molex connectors. Which action should you take based on the multimeter reading 10.24

The power supply is failing and should be replaced

You just purchased an iPad tablet device. You want to synchronize your photos, music, email, and contacts from your Windows 7 PC to the device. How can you connect the device to the PC? (Select Two)

USB cable Wi-Fi wireless connection

What device typically has both Type A and Type B USB ports?

USB-compatible hub

Which of the following devices typically has both Type A and Type B USB ports?

USB-compatible hub

You have just finished installing WIndows on a system that contains four physical hard disks. The installation process has created a system volume and a C: volume on the first disk (Disk 0). The installation process also initialized the second disk (Disk 1) and the third disk (Disk 2) but did not create any volumes on these disks. Which of the following would you expect to see as the status of Disk 1 and Disk 2?

Unallocated A disk that has been intialized will show as Unallocated if no volumes have been created. The Healthy or Online status indicated that the disk is turned on and can be accessed. The volume on the disk is valid and has no errors. The Formatting status is shown for volumes during the formatting process. After formatting, the status for the volume changes to Healthy. The Initializing process shows while a disk is being converted from a basic disk to a dynamic disk. After the conversion, the status for the volume changes to Healthy. The Unavailable status indicates that errors have occurred on physical or dynamic disks. The Unreadable status indicates a hardware failure, I/O errors, or other corruption but might also be caused by a delay in reading the disk in Disk Management.

You want to convert the partitions to simple volumes, preferably without losing any data. What should you do?

Upgrade the disk to a dynamic disk

You have an extra disk on your system that has three primary partitions and an extended partition with two logical drives. You want to convert the partitions to simple volumes, preferably without losing any data. What should you do?

Upgrade the disk to a dynamic disk. When you upgrade a basic disk to a dynamic disk, existing partitions are converted to simple volumes. You can convert the disk without deleting partitions or losing any data. Use the Convert command to change the file system from fat32 to NTFS. The partition table type (either MBR or GPT) does not affect the partition or volume type.

Your motherboard has two memory slots and supports a maximum of 8 GB of RAM. After installing two 4 GB modules and booting your system, you find that Windows only recognizes 3.5 GB of RAM. What should you do first?

Upgrade to a 64-bit version of Windows

You have a desktop computer that uses a 250 Watt power supply. You recently added a 4-disk RAID10 array to the system and now it spontaneously shuts down. What should you do?

Upgrade to a power supply that provides more watts

You have a desktop that you want to upgrade. You add several internal components and external components. You realize that you need to ensure that your power supply can support all of the new devices. What should you do?

Upgrade to a power supply that provides more watts

Your computer currently uses a 5,400 RPM hard disk. You want to improve your computer's overall performance by optimizing you hard disk performance. Which of the following would be the most effective means for optimizing your hard disk performance? (Select two.)

Upgrade your hard disk interface to SATA 3 Upgrade to a 10,000 RPM hard disk Upgrading to a 10,000 RPM hard disk and upgrading to a SATA 3 disk interface are the two most effective steps you can take to improve your computer's overall performance. The 7,200 RPM hard disk is not the fasted hard disk option. At 600 Mbps, the SATA 3 disk interface is twice as fast as the SATA 2 interface. Although hard disk drives are not capable of sending data at full 600 Mbps, they can go faster than the SATA 2 interface allows. Implementing RAID 0 does improve hard disk performance, but it requires a minimum of two disks. Adding another hard disk while keeping your current 5,400 RPM disk would not improve your hard disk performance as much as upgrading to 10,000 RPM hard disk with a SATA 3 disk interface.

Your computer seems to be running slow. In particular, you notice that the hard drive activity light stays lit constantly when running multiple applications and switching between open windows, even though you aren't saving large files. What could you do to troubleshoot the problem?

Use Resource Monitor to monitor memory utilization. Use Task Manager to monitor memory utilization.

You have a compiler that compiles applications used in your business. You want to make sure that the compiler continues to run in the background, even if yo open the other applications. How can you adjust the amount of attention given to that application?

Use Task Manager to adjust the process priority

You have an application that processes videos used in your online business, which requires a significant amount of processor time. You want to make sure that the application receives adequate access to the CPU, even if you open other applications. How can you adjust the amount of attention given to that application?

Use Task Manager to modify the process priority.

You have an application that renders videos used in your online business. You want to make sure that the application continues to receive adequate attention from the system CPU, even if you open other applications. How can you adjust the amount of attention given to that application?

Use Task Manager to modify the process priority.

You are building a new computer from both new and used parts. The video card is a PCIe video card that requires an 8-pin power connector. However, your power supply doesn't haven an 8-pin PCIe power connector. Which solution would be the least expensive option for your system?

Use an adapter cable to connect two 4-pin Molex connectors to the 8-pin PCIe connector

You're conducting scheduled maintenance on a laser printer. You notice that there is a build-up of excess toner inside the interior of the printer. What is the proper way to remove it?

Use an anti-static vacuum

You're conducting scheduled maintenance on a laser printer. You notice that there is a build-up of excess toner inside the interior of the printer. Which of the following is the proper way to remove it?

Use an anti-static vacuum

You want to combine storage space from two different hard disks into a single logical storage unit on your Windows computer.

Use dynamic disks and a spanned volume

You want to combine storage space from two different hard disks into a single logical storage unit on you Windows computer. What should you do?

Use dynamic disks and a spanned volume To use multiple disks in the single logical storage unit, upgrade all disks to dynamic disks. Create a spanned volume. A simple volume contains storage space from a single disk. Use basic disks to create primary and extended partitions. Partitions cannot include storage space from multiple disks.

What task would you complete as part of a SATA installation?

Use the 15-pin power connector

Which of the following tasks would you complete as part of a SATA installation?

Use the 15-pin power connector

A customer has called to complain that the colors in photos she has printed on the color inkjet printer your store sold her dont match the colors in the originals. Assuming the customer is using a Windows workstation, what should you do to resolve the issue? (2)

Use the Color Management tab of the printer driver to adjust the driver's color settings. // Download and install the latest printer drivers

A user in sales cannot get his laptop to display through a projector. He sees the screen output on the built-in LCD display, but the video is not being seen on the projector. What should you do first?

Use the Fn key to redirect display to the external video port

A user is sales cannot get his laptop to display through a projector. He sees the screen output on the built-in display, but the video is not being seen on the projector. What should you do first?

Use the Fn key to redirect display to the external video port

A user recently used her notebook to make a presentation that required her to display her screen from a projector in the conference room. She is now back at her desk, her notebook is still on, but the display is blank. What should you do first to try to restore the display?

Use the Fn keys to toggle display output to the laptop monitor

You decided to upgrade your PC with a faster processor. To do this, you ordered a new motherboard over the Internet that supports the processor you want to use. When it arrives, you discover that the motherboard uses the Mini-ATX form factor. Your current case is an ATX mid-tower with a standard ATX motherboard inside. What should you do?

Use the Mini-ATX motherboard inthe ATX case.

For the past several days, the print jobs from the inkjet printer are missing colors and leaving gaps What should you do to resolve the problem?

Use the automatic print head cleaning feature

How can you reformat a drive from FAT32 to NTFS without losing the existing data?

Use the convert command at a command prompt

which windows component prompts the user for credentials or permission to protect against unauthorized activities, such as an unintended software installation

User Account Control (UAC)

On a Windows system, which of the following is true of using groups?

User accounts are made members of a group. Group members have the access rights assigned to the group.

You are responsible for managing client workstations for your company. A user is unable to access data on an external HDD. You investigate the problem and determine that the US connection to the HDD is damaged. You replace the cable. What should you do next?

Verify full system functionality

You've just set up a color laser printer on a customer's windows workstation. You've connected it to the workstation using a USB cable and have loaded the appropriate drivers. What should you do next?

Verify that it is working correctly by printing a test page Edit the printer properties to configure paper tray and other device-specific settings

A user has called to complain that her computer won't boot. It stops at the BIOS startup screen right after the memory has been tested and displays a 301 keyboard error. What should you do first?

Verify that no keys are being pressed down during POST

One of your users has called to complain about her notebook computer. She reports that it displayed a message indicating that the battery was low, then it shut down all by itself even though it was plugged into the wall outlet. What should you check first?

Verify that the AC adapter LED light is lit when plugged into the wall outlet

What should you do when an error message appears stating that the drive is not accessible?

Wait. Then try again.

Which type of mobile device are fitness tracker wrist bands, smartwatches, smartglasses, and virtual reality headsets?

Wearable devices

A Windows workstation is configured to reveive its IP configuration information from a DHCP server on the company network. The user at the workstation reports that she cannot use email an dis unable to reach the Internet. Using the ipconfig command you see that the workstation has been assigned the following special IP configuration: -IP address: 169.254.0.1 -Subnet mask: 255.255.0.0

What is this special IP configuration called? -Automatic Private IP Addressing (APIPA). Why did the workstation receive this type of configuration? -The workstation was unable to contact the DHCP server. If a Windows client is configured to receive an IP address from a DHCP server, but cannot contact a DHCP server, it will automatically assign itself an IP address within the range of 169.254.0.1 to 169.254.255.254 with the subnet mask of 255.255.0.0 You can use APIPA instead of a DHCP server, but it should only be used on a small network that does not need a default gateway or DNS server setting configured.

Why would you recommend a dye sublimation printer?

When print jobs are detailed photographic reproductions.

When do you need to upgrade the system BIOS?

Whenever a BIOS update provides functionality not currently supported that is required by the OS or hardware

You currently use the Thurnderbird email client on your desktop PC. You use it to connect to an email server provided by a service provider using the IMAP SMTP protocols. You recently purchased an iPad and want to configure its Mail app to connect to your email server. Can you do this?

Yes, you can configure the Mail app on the iPad to connect to an email server using the IMAP and SMTP protocols

Which of the following scenarios would require selecting the FAT32 file system?

You need the disk to be backwards-compatible with older versions of Windows

In which of the following situations would restoring from a system image be the best option?

You need to restore a Windows system after a HDD failure

Your laser printer prints a vertical lack line on every page. You change the toner cartridge but the problem does not go away. What is the most likely problem?

a corona wire is dirty

What is the purpose of cache memory?

allows a processor to access date more quickly

What would most likely cause a random system lockup?

an overheated processor

Where should the thermal paste go when installing a processor?

between the heat sink and CPU

What type of authentication would require a user fingerprint or face recognition to get past the screen lock on a mobile device and get access to the device?

biometric authentication

What should you do before flashing the BIOS?

connect the computer to a UPS, backup CMOS settings

What does an ATX power supply do?

converts AC to DC

Which of the following Windows command line utilities would you use to realign the file structure on the disk to optimize performance?

defrag Use the defrag command to place files in contiguous order on the disk and thus realign the file structure to optimize performance. Use chkdsk to search the system for lost allocation units and corrupted files. The fdisk utility can be used on older versions of Windows to create, and delete partitions. You can use Disk Management to access the properties of a volume and then run the Defragmentation graphical utility from there.

Operates in half-duplex mode, meaning devices can either send or receive data at any given time

hub

What feature on Intel chips allows a single processor to run two threads in parallel, instead of processing single threads linearly?

hyper-threading

Closed source and second most popular mobile device operating system

iOS

Devices solely designed and developed by Apple

iOS

up to 30 meters in areas without interference

infrared

What should you do if there is less than 4 GB of memory available in Windows after installing a new OS?

install a 64-bit version of the operating system (it's most likely running 32-bit)

What should you do if you need parallel ports but they are not included on the motherboard?

install a PCI card to provide the necessary ports

You have a computer with dual core 64-bit processor. You want to install 32-bit Windows Vista. What should you do?

install the operating system normally. A 64-bit processor can run a 32-bit OS

You are the computer specialist in a small business. Your company server is named FS1 and has an IP address of 10.0.0.2. The hardware in you company server has started to experience intermittent failures, so you transferred the shares on the server to a spare server and took the main server offline. The spare server has an IP address of 10.0.0.3. You edit the existing A record for FS1 on your company's DNS servver and redirect the hostname to the spare server's IP address of 10.0.0.3. After doing so, most users are able to accress the shares on the spare server by host name, but serveral users cannot. Instead, they see and error message indication the FS1 server could not be found. Enter the command yo can run from the command prompt on these workstations that will allow them to access the shares on FS1 without performing a full restart.

ipconfig /flushdns Workstation maintain a cache of recently-resolved DNS names. When you use a DNS name, the computer first checks its cache. If the name is in the cache, the corresponding IP address will b used. This can sometimes cause problems if the IP address of a host has changed/ Old values in the cache might continue to be used for a time making communication using the DNS name impossible. To correct this problem on a Windows computer, run ipconfig /flushdns to delete the local DNS name cache

What is an advantage to purchasing a computer with video and audio integrated onto the motherboard?

lower overall system cost

Which of the following is an advantage of connecting a printer to a network

multiple users can print to the same printer

Which utility would you use to view current connections and active sessions and ports on a computer?

netstat

What term refers to increasing the clock speed of a component in an effort to increase performance?

overclocking

What is the most likely cause for your computer spontaneously shutting down?

overheated CPU

Which connectors are part of the system case and connect header pins on the motherboard?

power switch and hard disk LED light

You have a small wireless network that uses multiple access points. The network uses WPA and broadcasts the SSID. WPA2 is not supported by the wireless access points. You want to connect a laptop computer to the wireless network. Which of the following parameters will you need to configure on the laptop?

preshared key TKIP encryption

Connects two network segments that have different subnet addresses

router

What is true regarding single- and double-sided memory?

single-sided memory uses half the number of memory modules as double-sided memory of the same capacity

If a second CPU is removed, what must be replaced?

the terminating resistor

What function is not associated with a CNR?

video

Your Windows 7 client systems are joined to the WestSim.com domain. You need to verify that these clients are configured to get time from the correct time provider. Which commands can you use to do this?

w32tm /query /source. w32tm /query /status.

When do you need to upgrade the system BIOS?

whenever a BIOS update provides functionality not currently supported that is required by the operating system or hardware

What should you do first when a sound board stops working and has no audio?

- verify that the speakers are plugged into the correct jack and are powered on - verify that the volume isn't muted

A system board has four 32-bit RIMM slots. You installed one. What is true about installation?

- you can complete installation by installing three continuity modules - you can complete installing by installing three more RIMMs

What disk types does Windows support?

- Dynamic - Basic

What could be configured on these disks?

- Extended partitions with logical drives - Primary partitions

What storage device type uses magnetic film or aluminum platters for storing data?

- Floppy disk - Hard disk

What video card connectors provide digital video output?

- HDMI - DVI-D

What are most likely problems if you receive an error message?

- Incorrect disc format - Dirty or scratched disc

What is true of processor cache?

- L3 is shared between all cores - L1 is typically unique to a processor core

What are advantages of solid state storage compared to hard drives?

- Lower power requirements - No moving parts

What should you do if you can't save a file to a floppy diskette?

- Make sure the write-protection tab on the diskette isn't set - Verify that the diskette has been inserted and properly formatted

What connectors on the back of a computer are commonly used to attach a mouse to a modern PC system?

- Mini-DIN - USB A

The PS/2 ports on a computer are used for which types of devices?

- Mouse - Keyboard

Where should termination be enabled on this bus?

- On the DVD drive - On the external tape drive

Which pins on the 24-pin motherboard connector can be shunted to turn the power supply on>

- Pins 16 and 17 - Pins 15 and 16

Power supply for 24-pin connector

- only 24-pin connector - 20- and 4-pin connector

Replacement power supply specifications

- output wattage - form factor - processor connector

What is the most likely cause for an error message stating "Keyboard not present" during the POST?

- poor keyboard connection - a stuck key on the keyboard

What is the major difference between BTX and ATX standards

- processor slot rotated 45 degrees - improved thermal management

What should you do to make sure you have the right memory for a system?

- purchase additional modules that are the same as what is currently installed - check the motherboard documentation to find which modules are supported

You are purchasing a PC system that will be used as a file and print server in a small business. Which hardware selection criteria would be most important for this system? (select two)

1) 64-bit multi-core processor 2) RAID 1+0 array

You have a motherboard that requires a 24-pin connector from a power supply. What types of power supply could you use with this motherboard? (select two)

1) A power supply with 20-pin and 4-pin connectors 2) A power supply with a 24-pin connector only

A portable computer connected to a printer with an infrared interface works fine inside your office. However, when you go outside it works sporadically. How can you fix this? (select two)

1) Block any direct and reflected sunlight from the pathway between the PC and printer 2) Move the printer closer to the computer

Which of the following are optical storage devices? (select three)

1) Blu-ray Disk, or BD 2) CD 3) DVD

You want to use a wireless printer at home. The printer will be used by two computers in two different rooms. Which interfaces could be used to do this? (select two)

1) Bluetooth 2) Wireless Ethernet

When would you use the degauss feature on a CRT monitor? (select two)

1) The monitor displays strange colors 2) The monitor displays distorted images

You want to configure Power Plans on your Windows 7 laptop computer. Which of the following can do this? (select two)

1) In the Notification Area, double-click the battery icon. Click More Power Options 2) Go to Control Panel > System and Security > Power options

What are two major disadvantages to overclocking the CPU? (select two)

1) Increased heat output 2) Voided warranty

You have a notebook computer with a built-in wireless network card. One day it stops working. Because the network card is integrated onto the motherboard, you do not want to replace the entire motherboard. What can you use to connect to the wireless network? (select two)

1) Insert a wireless USB network card 2) Insert an ExpressCard wireless network card

What is a DB-15 connector on a sound card typically used for? (select two)

1) Joystick 2) MIDI port

Which of the following are characteristics of the ExpressCard /54 form factor? (select two)

1) L shape 2) 34mm wide at the connector

What is true of processor cache? (select two)

1) L3 is shared between all cores 2) L1 is typically unique to a processor core

Which connectors on the back of a computer are commonly used to attach a mouse to a modern PC system? (select two)

1) USB A 2) Mini-DIN

A user has called to complain that he can't save a file to a floppy disk in his floppy drive. What should you do first? (select two)

1) Verify that the disk has been inserted and properly formatted 2) Make sure the write-protection tab on the disk isn't set

The voltage on the yellow wire of a Molex connector should never drop below..

11 volts. If so it means the power supply is failing and must be replaced

Which of the following IP addresses belong to the Class A network 114.0.0.0?

114.0.0.15 114.58.12.0 114.122.66.12 With a Class A network, the first octet indicates the network address. All hosts on the network must have the same value in the first octet (114).

What is the maximum number of IDE devices that can be attached to the system?

12

You have a computer system with two IDE channels built into the motherboard. You add a PCI expansion card that provides an additional four IDE channels. What is the maximum number of IDE devices that can be added to the system?

12

Which of the following voltages are provided by an ATX power supply

12, 5, 3.3

You have a small home network that uses 192.168.1.0 with the default subnet mask for the network address. The default gateway address is 192.168.1.254, and the router is providing DHCP on the network. The Wrk2 computer has been assigned the IP address of 192.168.1.55. Which of the following is considered the loopback address for the Wrk2 computer?

127.0.0.1

What is the minimum number of hard disks that can be used to configure RAID5?

3

You have been asked to implement a RAID 5 solution for an engineer's desktop. What is the minimum number of hard drives disks that can be used to configure RAID 5?

3

Which port must be opened in the firewall of a Windows system in order Remote Desktop connections to be established with it?

3389

Which of the following are characteristics of the Express Card /54 form factor?

34mm wide at the connector L shape

Your laser printer prints a vertical line on every page. You change the toner cartridge but the problem does not go away. What is the most likely problem?

A corona wire is dirty

You recently installed a Windows 10 System. During the installation process, you elected to sign into the system using a local user account. After using the system for a time, you decide to being using an online Microsoft account to authenticate to the system instead. Click the option you would use in the Settings app t do this

Accounts

You want to create a new user account on a Windows system that can create and edit private files, start and stop the system, install applications, and add new device drivers. Which group should this user be a member of?

Administrators

You recently purchased a new sound cared and installed it in a free PCI slot in your computer. You plug in your old speakers, but you don't get any sound. You have checked all cable connections and they are secure. You have also ensure that the speaker volume is appropriately adjusted and isn't muted. What should you do next?

Check the vendor's Web site for an updated driver

When running a program on a Windows system, you get an error message indicating that a specific file (not the .exe file) cannot be located. What should you try first to fix the problem?

Check the working (Start In) directory identified in the shortcut

A user has called to complain that he can't connect to your organization's wireless network from his laptop. You know that the wireless signal is strong in his location. What should you do?

Check to see if the wireless adapter is switched off

Which of the following utilities would you use to correct cross-linked clusters within the file system on a Windows workstation?

Chkdsk

You replace the print cartridge on an inkjet printer/ What should you do next?

Calibrate the printer

Mary reports that an application's shortcut icon no longer launches the application. You check the documentation and find that you installed a new HDD in her computer. What should you do first so Mary can run the application?

Check the shortcut properties to make sure it is pointing to the correct file location

You are configuring an ADSL connection. Which of the following will be part of the configuration?

Filters or splitters RJ-11 connectors

You need to replace the video card in a laptop. What is the first step?

Find a service manual with correct disassemble procedures

You have installed a new computer with a dual core 64-bit processor, 6 GB of memory, and a PCIe video card with 512 MB of memory. After installing the operating system, you see less than 4 GB of memory available in Windows. What should you do?

Install a 64-bit version of the operating system

You are installing a floppy drive. You want the floppy drive to be the A: drive. How do you do this?

Install the drive after the twist in the ribbon cable

Page File Usage

Leave Blank

You have just finished upgrading the power supply in your desktop computer. Now the hard disk will not work. What should you do first?

Make sure the power connectors on the hard disk are plugged in all of the way

Which motherboard form factor allows for low-consumption power supplies

Mini-ITX

Which type of interface is typically used for internal wireless networking cards in laptops?

Mini-PCI

Which type of interface is typically used for internal wireless networking cards in the laptops?

Mini-PCI

Which type of interface is typically used for the internal wireless networking cards in laptops?

Mini-PCI

What kind of power connector does a floppy drive use?

Mini-molex power connector

Which kind of power connector is used on PATA (IDE) internal HDDs and optical drives?

Molex

Form factor - uses a riser card instead of expansion card slot

NLX

Which term refers to the portion of the hard drive where print jobs are stored before going to the print device?

Print queue

What 2 printer management components would you use to view the port used by a printer?

Print server properties // Printer properties

Which printer management component would you use to view the drivers used by a printer?

Printer properties // print server properties

On a Windows system, which Task Manager tab would you use to adjust the priority given to a specific program?

Processes

Which computer function takes data through a series of procedures as defined by a set of instructions?

Processing

What is an advantage of SATA over PATA?

Faster data transfer speeds

Which of the following is an advantage of SATA over PATA?

Faster data transfer speeds

What are lookback plugs used for?

Testing ports by returning output signals as input

Which of the following is true of the way many large digital media vendors are using Digital Rights Management technology?

They are moving away from DRM because of several key shortcomings in the technology. They are adopting alternatives to DRM such as encouraged customers to not illegally share digital files.

What is a characteristic of extended partitions?

They are subdivided into logical drives

What category do apps fall into if they have been signed with a certificate?

Trusted

For the past several days, the print jobs from the inkjet printer are missing colors and leaving gaps. What should you do to resolve the problem?

Use the automatic cleaning feature

You decided to upgrade your PC to use a faster processor. To do this, you ordered a new motherboard over the internet that supports the processor you want to use. However, when it arrives, you discover that the motherboard uses the mini-ATX form factor. Your existing PC's case uses the ATX form factor. What should you do?

Use the mini-ATX motherboard in the ATX case

Which component of Windows 7 prompts the user for credentials or permission to minimize the dangers of unintended software installations?

User Account Control (UAC)

Which of the following paper types should not be used in Inkjet printers?

Very glossy paper

Which of the following functions are not associated with a CNR?

Video

Which of the following functions are not associated with a CNT?

Video

What is the purpose of the dxdiag tool?

View information related to DirectX operation.

On the main network printer, another user's print job has stalled. You try to delete that print job, but can't. What is the reason why you can't delete the print job?

You do not have the Manage documents permission

What is a ZIF socket?

a special socket for inserting and securing a processor

Which of the following conditions would typically result in replacing the drum on a laser printer?

Spots at regular intervals on the page

You are in the process of installing a motherboard in a system case. Which of the following objects should you place between the motherboard and the system case?

Standoffs

You are in the process of installing a motherboard in a system case. Which of the following objects would you place between the motherboard and the system case?

Standoffs

Which of the following devices typically use a microUSB connector

Smartphones, Digital cameras

This can require more memory and can cause problems if there is not enough memory at this time

Software installation.

You are looking at a female TRS connector on the computer. What devices use this connector?

Speakers

What is the effect on your system when you run Disk Defragmenter?

Speeds up disk I/O performance

What should you do if you want to add a second processor to you dual-processor system?

match the speed of the new processor with the speed of the existing processor

What components should you consider upgrading to run several applications?

memory

The memory is not compatible and was not installed and configured properly

memory upgrade

You suspect large packets are being dropped on your network because of their large size. Which utility can you use to confirm your suspicion?

ping -l

Which component converts AC to DC?

power supply

What requires either all memory slots are populated with memory modules or with a continuity module

rambus

What should you do before you upgrade your computer to a faster processor?

read the motherboard documentation to identify which processors are supported

What is not recommended for keeping computer cool?

remove unused expansion card slot covers

What action will not help to keep the system cool?

removing the computer case

What must you do if you want to upgrade your computer to a dual-core system?

replace the existing processor

What type of card are attached to the motherboard to allow expansion cards to plug into them instead of the motherboard?

riser

Up to 100 Meters for class 1 devices

bluetooth

up t 10 meters for class 2 devices

bluetooth

Can be used to connect wireless clients to wired clients on the same network

bridge

What should you do when you can't hear any sound when you play a music CD in the drive?

connect the audio port on the DVD drive to the audio input on the sound card or motherboard

Incompletely or improperly doing this can cause errors that appear to be memory related

hardware installation or removal

Which mechanisms could you use to resolve a hostname into its associated IP address?

hosts file DNS You can use the Domain Name System (DNS) to get the IP address from a given host name. You can also use the local hosts file to map host names into IP addresses. On Windows systems, the file is located in C:\Windows\system32\drivers\etc\. You can use either the DHCP protocol or the BOOTP protocol to assign IP address and other configuration information to hosts automatically. Use FTP to transfer files.

What should you place between the motherboard and the system case?

standoffs

What is the approximate bus speed of DDR2 memory rated at PC2-5300?

333 MHz

What could be detrimental while flashing the BIOS?

loss of power

Common voltages produced by a desktop power supply

+/- 12v +/- 5v

You are trying to troubleshoot a power supply issue with a voltmeter. Which two of the following options are common voltages produced by a desktop power supply

+/- 12v +/- 5v

What is true about power supply wattage?

- "watt" describes how much work or how much power can be supplied to various devices - wattage requirement for each individual circuit uses the formula: W = V x A

What is true of the SXGA screen resolution?

- 1280x1024 - 5:4 aspect ratio

What instruction sets do 32- and 64- bit processors use?

- 64-bit uses the x86-64 - 32-bit uses only IA-32

Which of the following is true of online software activation?

- Before running a newly installed application, the user must activate their license online on the software vendor's website. - With personal software licenses, the limit is usually 1-3 online activation. - Persistent activation may require the license to be continuously re-activated online at a preconfigured interval

What are optical storage devices?

- CD - DVD - BD

What are CRT monitor characteristics?

- CRT monitors use an electron beam that hits phosphor dots inside of a vacuum tube - CRT monitors have a 4:3 aspect ratio which matches the display ratio of a television set

Which are required tasks to add space to the existing volume?

- Create an empty folder on the C:\ drive - Run the convert command

You need to install a 32-bit application on a 64-bit version of Windows. Where is the default directory where the application will be installed?

%systemdrive%/Progra, Files (x86)

You need to install a 32-bit application on a 32-bit version of Windows. Where is the default directory where the application will be installed?

%systemdrive%/Program Files.

How many IRQs are needed for three USB devices connected to a hub?

1

You have connected a USB hub to your computer. Connected to the hub is a scanner, a USB thumb-drive, and an external HDD. How many IRQs are needed for the USB devices?

1

You are trying to troubleshoot a power supply issue with a voltmeter. Which of the following options are common voltages produced by a desktop power supply? (select two)

1) +/- 5v 2) +/- 12v

Which of the following are characteristics of Bluetooth? (select two)

1) 2.4 GHz radio wireless 2) Ad hoc connections

Which of the following tools allow for remote management of servers? (select two)

1) Telnet 2) SSH

What is the max range for the Bluetooth 2.0 specs for Class 1 devices?

100 M

Which of the following are valid IPv6 addresses?

141:0:0:0:15:0:0:1 6384:1319:7700:7631:446A:551:8940:2552

Which port does Telnet use?

23

What is the maximum transmission speed for Bluetooth devices?

3 Mbps

Whatmotherboard power connectors typically connect directly to the motherboard?

4-pin CPU power and 24-pin motherboard power

You have been asked to implement a RAID 10 solution for a video editor's desktop workstation. What is the minimum number of hard disks that can be used to configure RAID 10?

4. A RAID 10 array nests a mirrored array within a stripped array. To create a RAID 10 array, a minimum of four hard disks is required (two for the mirrored array and two more to stripe the mirror).

What is the max cable length for the IEEE 1394a standard?

4.5 meters

What is the maximum cable length for the IEEE 1394a standard?

4.5 meters

Which ribbon cable is used by an ATA/133 HDD?

40-pin / 80-wire

Which ribbon cable is used by an ATA/133 hard drive?

40-pin / 80-wire

What is the max data transfer rate of an IEEE 1394a device?

400 Mbps

What is the maximum data transfer rate of an IEEE 1394a device?

400Mbps

You have a CD-RW drive that advertises speeds of 32x/12x/48x. What is the read speed of the drive?

48x

A SCSI HDD has three jumpers that are used to set the SCSI ID. Shunts have been placed on the first and third jumpers. What SCSI ID has been assigned to this device?

5

Voltages provided by an ATX power supply

5, 3.3, 12

What is the maximum data transfer speed for USB 3.0 devices?

5Gbps

Which of the following printers would produce the highest print quality?

600 DPI

How many devices does a single IEEE 1394 bus support?

63

What is the most important consideration when building a computer that supports 6 GB of memory?

64-bit processor

You want to build a new system that supports 6 GB of memory. Which of the following will be the most important consideration when building the computer?

64-bit processor

Which wireless standard has the highest data transfer rates?

802.11n

You have a laptop with a dual core processor with the following characteristics: * 1024 MB L2 cache * 125 Watts * 45nm process size You want to upgrade the processor to one that uses less power. Which of the following characteristics would most likely identify a processor that uses less power?

90 Watts

Characteristic of a processor that uses less power

90 watts

What is a recovery partition?

A partition created by the computer manufacturer to restore the system to its original state

You have a motherboard that uses a 24-pin ATX connector. Which types of power supply could you use with this motherboard?

A power supply with a 24-pin ATX connector only A power supply with a 20-pin ATX and a +4 pin connector

Check Disk detects disk integrity errors and fixes them. Match the types of errors Check Disk detects and fixes on the left with the error description on the right.

A series of used clusters on the hard disk drive that are not associated with a specific file - Lost clusters Occurs when two files claim the same cluster - Cross-linked file Files that exist on the hard drive but which are not associated with a directory in the index - Orphaned files A portion of the hard disk that cannot be used - Bad sector Check Disk detects disk integrity errors and fixes them. Errors that can be checked and fixed by Check Disk include: -Lost clusters are series of used clusters on the hard disk drive that are not associated with a specific file. -A cross-linked file occurs when two files claim the same cluster. Check Disk will identify cross-linked files and correct their cluster associations. -Orphaned files are files that exist on the hard drive but which are not associated with a directory in the index. Normally Check Disk can re-associate the file with correct directory. -A bad sector is a portion of the hard disk that cannot be used. Bad sectors are marked so that they are no longer used. Any used bad sectors are redirected to another sector.

What is ZIF socket

A special socket for inserting and securing a processor

What is a ZIF socket?

A special socket for inserting and securing a processor

Which of the following statements about the Dynamic Hosts Configuration Protocol (DHCP) are true?

A workstation must request addressing information from a DHCP server. It can deliver a DNS server address in addition to the host IP address. DHCP servers deliver IP addresses as well as other host configuration information to network hosts. DHCP can be configured to assign any available address to a host, or it can assign a specific address to a specific host. DCHP clients, typically workstations, must send a request to a DCHP server before it will send IP addressing information to them.

What expansion buses are most commonly used for video cards in modern computer system?

AGP and PCI Express

What partition type identifies the partition as one that holds the boot loader program used to start the operating system?

Active

What type of SCSI termination uses voltage regulators in conjunction with resistors to terminate the SCSI bus?

Active Termination

Which of the following types of SCSI termination uses voltage regulators in conjunction with resistors to terminate the SCSI bus?

Active Termination

If you want to boot from a hard drive, what must it have?

Active partition

A user works primarily in your organization's production area. However, she frequently needs to access data stored on her Windows 10 desktop system in her office while on the production floor. She would like to be able to use a system in the production are to remotely access her desktop system using a network connection. Which groups on her desktop system could you make her user account a member of enable this configuration?

Administrators Remote Desktop Users

You have a computer with a Pentium IV CPU and two PC-2400 DDR modules. The motherboard has room for two additional memory modules, and you'd like to install two PC-4000 modules. Which of the following statements is true?

All memory will operate at 300 MHz

What is the purpose of cache memory?

Allows a processor to access data more quickly

Which of the following is true of LED monitors?

LED monitors use LED backlight technology.

Which of the following protects a computer from electrostatic discharge?

Anti-static wrist strap

What component is an example of firmware?

BIOS

You need a type of wireless connection that can transfer data between your phone, PDA, and laptop. You are transferring sensitive information. Which would be the best choice?

Bluetooth

You want to use a wireless keyboard and mouse with your laptop computer. Which method should you choose?

Bluetooth

One day while trying to start your Windows XP computer, the system displays the following error: Invalid partition table. Which of the following will most likely fix the problem?

Boot into the recovery console and run the fixmbr command on the boot volume

While using a new Windows system, you find that the double-click speed setting on the mouse pointer is set much slower than you would prefer. You want to increase the double-click speed setting. Click the tab you would use in the Mouse Properties window to do this.

Buttons

The integrated mouse, the small monitor, and the compact nature of the keyboard are impeding your work when you use a notebook, but you still need a system that is portable if necessary. What is your best option?

Buy a docking station for your notebook

What interface can be used to connect a keyboard and mouse?

PS/2

Which of the following is a valid MAC address?

C0-34-FF-15-01-8E

Which computer component is necessary to save system settings when you power off the computer?

CMOS battery

Which of the following components is necessary to keep the real-time clock running?

CMOS battery

Which of the following components is necessary to save system settings when you power off the computer?

CMOS battery

The screen display seems to be fuzzy at some spots. What should you do to correct the problem?

Change the screen resolution to the native resolution of the monitor

You have purchased a SXGA LCD monitor and connected it to the DVI-I port on your computer using a DVI-D cable. You configure the screen resolution at 1600 x 1200 with 24-bit color. The sceen display seems to be fuzzy at some spots. What should you do to correct the problem?

Change the screen resolution to the native resolution of the monitor

You have purchased an LED monitor and connected it to the DVI-I port using a DVI-D cable. You configure the screen resolution to 1440 x 900 with 24-bit color. The screen display seems to be fuzzy. What should you do to correct the problem?

Change the screen resolution to the native resolution of the monitor

Which of the following would indicate when a system case cover is removed?

Chassis intrusion detection

Which of the following disk maintenance utilities optimizes the performance of your hard drive by verifying the files system integrity of a hard disk and fixing the errors it detects?

Check Disk Check Disk is a utility that verifies the file system integrity of a hard disk. Check Disk detects disk integrity errors and fixes them. Disk Defragmenter optimizes the performance of your hard drive by joining fragments of files that are in different locations on your hard drive into a single location. The more information that is on the drive, the more time it will take to defragment the drive. Disk Cleanup helps manage disks by locating and disposing of files that can be safely removed from the disk. Check Disk is a utility that verifies the file system integrity of a hard disk. Disk Management is a tool for viewing, modifying, and creating partitions.

You want to make sure that you always have the latest patches installed on you workstation for an order entry application created by DataComLink corporation. What should you do?

Check the DataComLink Website regularly for patches and updates to the software. Configure the application to automatically download and install updates as they are released.

You would like to install Windows on a computer that previously had another OS installed on it, but you aren't sure if the audio card is compatible. The installed audio card is a SoundMax D1371 (PCI). What should you do?

Check the manufacturer website for compatibility information

Which of the following interfaces can be used to connect a keyboard and mouse?

PS/2

Where is Disk Management located within Windows?

Computer Management

Where is Disk Management located within Windows 7?

Computer Management Within Windows 7, Disk Management is found under storage in Computer Management, Within Windows 10, Disk Management is found in the list of utilities that appear when you right-click the Start Menu.

Which of the following terms describes the different between white and black in an LCD monitor?

Contract ratio

What term describes the difference between white and black in an LCD monitor?

Contrast ratio

Which of the following terms describes the difference between white and black in an LCD monitor

Contrast ratio

The power cord for the laptop has a block on it (sometimes called a brick). What does this block do?

Converts AC power to DC power

What does an ATX power supply do?

Converts AC to DC

Which of the following functions are performed by the TPM?

Create a hash of system components

What should you do to add space to the C:\ drive?

Create a mount point using space on the second disk

You manage Windows desktops for your organization. You recently updated all of your workstations to Windows 7. Your organization relies on a particular application, which worked correctly in earlier versions of Windows, but now does not run in Windows 7. You have checked the application vendor's website, but there is no update available. What should you try next to run the application?

Create a virtual computer that runs Windows XP. Run the virtual computer each time the application runs. Run the application in compatibility mode.

You are responsible for managing client workstations for your company. A user reports that she can't turn her computer on. After some investigation, you find that the power supply is malfunctioning. What should you do next?

Create an action plan

Which term refers to a situation where two files try to claim the same cluster on the HDD?

Cross-linked clusters

Which term refers to a situation where two files try to claim the same cluster on the hard disk?

Cross-linked clusters

Which memory rating identifies the fastest memory?

DDR3-2000

What term is used to identify memory modules?

DIMM

Which of the following are terms used to identify memory modules?

DIMM

What is typically used for large data backups of servers?

DLT tape

Which of the following is typically used for large data backups of servers?

DLT tape

What media types is not hot swappable?

DVD drive with an IDE interface

You have a computer with three HDDs. A RAID0 volume uses space on Disk 1 and Disk 2. A RAID1 volume uses space on Disk 2 and Disk 3. Disk 2 fails. Which of the following is true?

Data on the RAID 1 volume is accessible; data on the RAID 0 volume is not

You have a computer with three hard disks. Which of the following is true?

Data on the RAID1 volume is accessible; data on the RAID0 volume is not

Users have been experiencing periodic system lockups that generate the same error message. After checking Microsoft's Web site, you find that a hotfix is available to address the issue. What should you do next?

Deploy the hotfix on a test computer.

On a Windows 10 system, which Task Manager tab would you use to adjust the priority given to a specific program?

Details

What component in a laser printer applies toner to the drum, causing the tone to stick to the charges areas of the drum?

Developing roller

When you print from your laser printer, the paper contains faint images from previous printouts. Which components should you check?

Discharge lamp, rubber scraper

Which of the following disk maintenance utilities will locate and dispose of files that can be safely removed from the disk?

Disk Cleanup Disk Cleanup helps manage disks by locating and disposing of files that can be safely removed from the disk. Disk Defragmenter optimizes the performance of your hard drive by joining fragments of files that are in different locations on your hard drive into a single location. Check Disk is a utility that verifies the file system integrity of a hard disk. Disk Management is a tool for viewing, modifying, and creating partitions.

Which of the following disk maintenance utilities optimizes the performance of you hard drive by joining parts of files that are in different locations on the hard drive into a single location?

Disk Defragmenter Disk Defragmenter optimizes the performance of your hard drive by joining fragments of files that are in different locations on your hard drive into a single location. The more information that is on the drive, the more time it will take to defragment the drive. Disk Cleanup helps manage disks by locating and disposing of files that can be safely removed from the disk. Check Disk is a utility that verifies the file system integrity of a hard disk. Disk Management is a tool for viewing, modifying, and creating partitions.

Which tool would you use to create and delete partitions on hard drives?

Disk Management

You have physically installed a new HDD in your computer and configured the disk in the BIOS using the CMOS setup program. You try to access the HDD in Windows Explorer but the drive is not displayed. Which utility will you most likely use to solve the problem?

Disk Management

You want to read the flash drive on your computer as quickly as possible with the least amount of effort.

Do nothing. Windows 7 can natively access exFAT file systems

What kind of printer uses inked ribbon?

Dot Matrix

What is an error detection technique that can also correct the error?

ECC

Which of the following is an error detection technique that can also correct the error?

ECC

Which of the following is an error detection technique that can also correct the error?

ECC, or Error Checking and Correction

What should you do if a device runs in USB 1.1 mode instead of 2.0 mode?

Edit the CMOS settings to configure the USB ports to use USB 2.0

Which of the following describes an IPv6 address?

Eight hexadecimal quartets 128-bit address

You want to use Hibernation on your Windows notebook. What does it need to have?

Enough free HDD space

You want to use Hibernation on your Windows notebook. What does it need to have?

Enough free hard drive space

Which utility can be used to view when a service was stopped as well as any error messages generated by the service?

Event Viewer

You are removing screws within a computer, but several have fallen into places you can't reach. Which tool would help retrieve the small screws?

Extension magnet

What file system should you choose to format a 64 GB flash drive?

FAT64

Memory is not properly seated, missing, or the motherboard is defective

First boot of a new computer

You have an existing computer that you've been using for years. You decide to upgrade the processor. You check the motherboard documentation and purchase the fastest processor that is supported by the motherboard. When you start the computer, it beeps regularly but nothing is shown on the screen and it doesn't start. What should you do first?

Flash the BIOS

You have just purchased a used laptop and you want to configure it to hibernate when you press the power button. You edit the Power Options settings and enable hibernation, then you configure the power button to trigger hibernation. Everything works fine for several weeks. However, one day when you press the power button, the laptop does not hibernate. What should you do?

Free up disk space

You have just purchased a used laptop and you want to configure it to hibernate when you press the power button. You edit the Power Options settings and enable hibernation, then you configure the power button to trigger hibernation. Everything works fine for several weeks. However, one day when you press the power button, the laptop does it hibernate. What should you do?

Free up disk space

After removing the printed paper from your laser printer, the toner smudges and can be wiped off in places. Which of the following is most likely the problem?

Fuser rollers

You are purchasing several PC system that will not be used as thin clients in a large organization. Which hardware selection criteria would be most important for this system?

Gigabit Ethernet adapter

You are purchasing several PC systems that will be used as thin clients in a large organization. Which hardware selection criteria would be most important for this system?

Gigabit Ethernet adapter

Most devices that you install in a system require little to no configuration; they simply work after you plug them in. This is because devices are automatically assigned the system resources needed for the device to begin functioning. What are the three types of system resources that are usually automatically assigned?

I/O address IRQ, DMA channel

Which tool would be the best choice to remove and replace the motherboard BIOS chip?

IC extractor

You want to use your Windows workstation to browse the web sites on the Internet. You use a broadband DSL connection to access the Internet. Which network protocol must be installed on your workstation to do this?

IP The IP is the protocol of the Internet. If you want to use the Internet, your computer must have the IP protocol installed and configured. The Serial Line Internet Protocol (SLIP) is a mostly obsolete encapsulation of the Internet Protocol designed to work over serial ports and modem connections. The Point-to-Point Protocol (PPP) is also commonly used with modem connections. IPX/SPX is the protocol suite used on legacy NetWare networks. NetBIOS is the term used to describe the combination of two protocols: NetBEUI and NetBIOS. NetBIOS was used in early Windows networks. Because NetBIOS is a non-routable protocol, it was often combined with TCP/IP or IPX/SPX to enable internetwork communications.

You are responsible for managing client workstations for your company. A frantic user calls you one morning claiming that "nothing is working". What should you do first in your troubleshooting strategy?

Identify the problem

What is true regarding IDE master and slave settings?

If two IDE devices share the same channel, one device must be set to master and the other must be set to slave

You have a laptop running Windows 10. User Account Control (UAC) has been disabled. How would you re-enable UAC on the laptop?

In the Control Panel, select User Accounts, then User Accounts In the Control Panel, select System and Security, then Security and Maintenance

What is not an advantage of SSDs over HDDs

Inexpensive

You want to configure a RAID1 array in the computer. What should you do?

Install the drivers for the RAID controller?

Which of the following actions taken on a Windows workstation will directly improve system security?

Install the latest updates.

Which of the following battery types offers the greatest storage capacity in the smallest amount of space?

Lithium Ion (Li-Ion)

Which of the following actions will you take as part of the configuration?

Load the RAID drivers during operating system installation

You are configuring a new system and want to use a RAID 0 array for the operating system using SATA disks and RAID functionality built into the motherboard. Which of the following actions will you take as part of the configuration?

Load the RAID drivers during operating system installation. If using an onboard RAID controller with SATA drives, edit the CMOS settings and identify the drive type as RAID. This tells the system to load the onboard BIOS for accessing the connected drives. If you want to install the operating system on a RAID array, you will need to manually load the controller driver so that Windows can see the RAID array.

Which of the following could be detrimental while flashing the BIOS?

Loss of power

What is an advantage of the exFAT file system over NTFS?

Lower memory and processor resource use

Which printer permission would you assign to a user so that she can pause the printer?

Manage this printer

A computer has a HDD and a DVD drive installed on the primary IDE channel. You decide to move the DVD drive to the secondary IDE channel. The secondary IDE interface will have no other device. What setting should you configure on the DVD drive?

Master or Single

What setting should you configure on the DVD drive?

Master or Single

You want to add a second processor to your dual-processor system. Which of the following should you do?

Match the speed of the new processor with the speed of the existing processor

What is the most important consideration when choosing a rewritable DVD drive?

Media compatibility

You are in the process of configuring a new computer. The motherboard has four memory slots and supports duel channel memory. You install two memory modules. When you boot the computer, the BIOS recognizes both modules, but the memory is not configured to run in dual channel mode. What should you do?

Move the modules to the correct motherboard slots

You have purchased a used computer from a computer liquidator. When you boot the computer, you find that there has been a password set on the BIOS. You need to clear the password so that you can edit the CMOS settings. You want to keep all other CMOS settings. What should you do?

Move the motherboard jumper

You have a power supply configured to receive 110 volts AC. How can you configure the power supply to receive 220 volts AC?

Move the power switch on the power supply to a different voltage

Which of the following is the most common method for removing RAM from a motherboard?

Move the tabs holding the RAM out of the way; pull straight up to remove the RAM

What CRT monitor is capable of producing a picture with the least amount of flicker?

Non-interlaced

Which of the following CRT monitors is capable of producing a picture with the least amount of flicker?

Non-interlaced

Which of the following will most likely contain SODIMM memory?

Notebook computers

What is a required task to add space to the existing volume?

On the new hard disk, create a new partition without a drive letter

Which of the following terms refers to increasing the clock speed of a component in an effort to increase performance?

Overclocking

Lately your computer is spontaneously shutting down after only a few minutes of use. What is the most likely cause?

Overheated CPU

What expansion buses are most commonly used for devices such as sound cards, modems, and network cards?

PCI

Which of the following expansion buses is most commonly used for devices such as sound cards, modems, and NICs?

PCI

Which of the following expansion buses is most commonly used for devices such as sound cards, modems, and network cards?

PCI

What problem is common for dot matrix printers?

Paper scraps are caught in the feed mechanism

You need to use Task Manager to analyze memory utilization on a Windows system. For example, you need to see how much system RAM is currently in use and how much is available. Click on the tab in Task Manager that you would use to do this.

Performance

Which tool can you use to gather and display statistics that help you monitor the operation of a Windows system?

Performance Monitor

You manage a Windows system. You want to view information about your computer including the CPU utilization information about disk I/O operations. Which tools could you use to do this?

Performance Monitor Task Manager

You have an AMD processor and an Intel processor, both of which have the same speed rating and both of which use the same front-side bus rate. Which of the following statements is true about the relative performance of both processors?

Performance will depend on other factors such as cache and other features

Which of the following is an extra button or knob on a laptop keyboard that moves the mouse cursor?

Point stick

What RAM standard requires heat spreaders?

RAMBUS

Your company uses Windows as a desktop OS. You need to install a new Plug-and-Play print device on a user's computer. The printer uses a parallel port interface. You connect the print device to the computer's parallel port and turn the device on. You want to use the drivers provided by the manufacturer rather than those that ship with Windows. What should you do?

Run the setup program provided by the print device's manufacturer

What port would you likely to find on the mother board faceplate that indicates digital audio support?

S/PDIF

You want to purchase a motherboard that has a built-in digital audio output. Which port would you likely find on the motherboard faceplate that indicates digital audio support?

S/PDIF

You want to purchase a motherboard that has built-in digital audio output. Which port would you likely find on the motherboard faceplate that indicates digital audio support?

S/PDIF

What protocol is used to send e-mail messages from a mail client to a mail server?

SMTP SMTP sens email from a mail client to a mail server. FTP provides a generic method of transferring files. SNMP is used in network management systems to monitor network-attached devices for conditions that warrant administrative attention. POP3 and IMAP are both e-mail protocols used by mail clients to retrieve e-mail from a mail server; however they can be used to send mail from the client to the server. The Trivial File Transfer Protocol (TFTP) is used for network file transfers.

What is name of the utility, which is similar to Telnet, that you can use to establish a secure remote server management session?

SSH

Which of the following can be used to create a secure connection to a remote server?

SSH

Which task will be required in the configuration process?

Set the drive type in the BIOS to IDE

You are installing the first SATA drive into a desktop, but you do not have the drivers for the motherboard's integrated SATA controller. Which of the following tasks will be required in the configuration process?

Set the drive type in the BIOS to IDE

What should you do after you've purchased an external SCSI hard drive for your desktop workstation?

Set the drive's SCSI ID

You just purchased an external SCSI hard drive for your desktop workstation. What should you do before you connect it to the system?

Set the drive's SCSI ID

On a Windows 10 workstation, you want to use the Storage Spaces feature to create a logical drive. Which of the following components are used to configure Storage Spaces? (Select three.)

Storage devices, which are physical drives such as SATA drives or external drives. Storage spaces, which are logically defined units created from a pool of storage. Pools of storage, which are logically created from free space on storage devices. Storage spaces are comprised of three components: -Devices are the hard disks or other types of storage form which storage pools are created. You can use a variety of devices such as SATA drives and external drives to create storage pools. -Pools of storage are created from the available disk space. A pool is a logical concept composed of the free space available on the specified storage devices. -Storage spaces define logical units of space created from a pool. One or more storage spaces can be created from the pool. To the Windows system and the user, storage spaces appear as disks with typical drive letters (e.g., E: drive, F: drive). Parity, thin provisioning, and data resiliency are benefits of Storage Spaces.

Which ACPI power state retains the contents in RAM, but turns all other components off?

Suspend

You need to configure when Windows checks for and downloads updates from Microsoft's update servers on a Windows 7 system. Which option in Control Panel should you use to do this?

System and Security

You need to enable Remote Desktop on a user's Windows 10 system s that you can manage it over the network from your office. Click the option you would use in Control Panel to do this.

System and Security

Your computer has a quad-core processor that supports multi- threading installed. Given that the system is running Windows, how can you verify whether multi-threading has been enabled?

Task Manager can display CPU utilization graphs for eight processors.

Which tool lets you automatically start an application or run a script based on triggers?

Task Scheduler

You have an application that you would like to run every Monday a 3 p.m. on your Windows workstation. Which tool would you use to configure the application to run automatically?

Task Scheduler

You have an application that you would like to run every Monday at 3 p.m. on your Windows workstation. Which tool would you use to configure the application to run automatically?

Task Scheduler

When you boot the computer, it hangs after asking you for the current time and date. What is the most likely problem?

The CMOS battery has failed

What is a good reason to not recommend a solid ink printer?

The user has a surplus of toner carttridges and would like a printer that can be used with these

Match the disk status on the left with the corresponding description on the right. Each status may be used once, more than once, or not at all. -Shows while a disk is being converted from a basic disk to a dynamic disk -Indicated that the disk is turned on and can be accessed and the volume on the disk is valid and has no errors -Indicates that errors have occurred on physical or dynamic disks -Shows when a dynamic disk has been removed or turned off

The Healthy or Online status indicates that the disk is turned on and can be accessed. The volume on the disk is valid and has no errors. The Initializing process shows while a disk is being converted from a basic disk to a dynamic disk. After the conversion, the status for the volume changes to Healthy. The Unavailable status indicates that errors have occurred on a physical or dynamic disks. The Missing or Offline status shows when a dynamic disk has been removed or turned off.

You're troubleshooting a malfunctioning notebook computer system. The user has indicated that the screen is always dark and difficult to read even while the system is plugged in to a wall outlet. You check the system and determined that the backlight isn't working. Which of the following could be the cause.

The LCD cutoff switch is stuck in the OFF position

What is the advantage of hot-swapping for storage devices?

The OS automatically detects hot-swappable storage devices, configures drivers, and enabled the devices

Which type of printer boils the ink in its print head to print?

Thermal inkjet (bubble jet)

While troubleshooting a network issue, you successfully ping the 127.0.0.1 IP address. Which of the following is true?

The TCP/IP protocol suite is working correctly on this computer

What is the biggest advantage of 64-bit processors over 32-bit processors?

The ability to use over 4 GB of memory

What is true about primary partitions?

The active partition must be a primary partition

Which of the following is true about primary partitions?

The active partition must be a primary partition A primary partition is a partition type used on basic disks. The active partition must be a primary partition. Each physical disk can have up to four primary partitions, or three primary partitions and one extended partition. Logical drives are defined within an extended partition.

You have installed a new device in your system, and have run the Add A Device Control Panel applet. Under what circumstance would it be appropriate to continue with the wizard if the device was not discovered?

The device does not support Plug-and-Play

You plug a USB 2.0 external storage device into a USB 3.0 port on your computer. Which of the following statement is true regarding the device?

The device will work, but will only transfer at USB 2.0 speeds

Your iPad is configured to do remote backups everyday to iCloud. What conditions are required for the iCloud backup to take place

The iPad has to be plugged into a power source The iPad screen has to be locked The iPad has to have an Internet connection

Memory Pages per Second

The number of hard faults that occur each second.

Disk Queue Length

The number of read and write requests that are waiting to be processed.

You installed a new floppy disk drive and the light stays lit. What is the most likely problem?

The ribbon cable is connected backwards

You just installed a new floppy drive. After booting, the drive light stays lit. What is the most likely problem?

The ribbon cable is connected backwards

You system volume is running out of disk space. You need to extend the system volume to give it more space. Which of the following conditions must be met to extend the system volume? (Select all that apply.)

The system volume must formatted with NTFS. The disk must have contiguous free space on the same disk. The system volume can only be extended using contiguous free space on the same disk. This is the same for both basic and dynamic disks. Any volume can only be extended if it is unformatted or formatted with NTFS. The system volume can be on either a basic or dynamic disk. The system volume cannot be extended or spanned to non-contiguous space or to space on another disk.

A user calls to report that she is experiencing intermittent problems while accessing the wireless network from her laptop computer. While talking to her, you discover that she is trying to work from the break room two floors above the floor where she normally works. What is the most likely cause of her connectivity problem?

The user is out of the effective range of the wireless access point on her floor

A user receives printouts consisting of several pages of seemingly random characters every time he prints to a network printer. The printer seems to work fine for all other users. What is the most likely cause of the problem?

The user is using an incorrect printer driver

Which of the following is a characteristic of extended partitions?

They are subdivided into logical drives. An extended partition is subdivided into logical drives. You cannot format an extended partition, you can only format the logical drives within the partition. You can have only a single extended partition per disk. The extended partition cannot be set as active, and therefore cannot be used to boot the computer. Use a primary partition to set the partition as active, boot the computer or to create multiple partitions per disk.

Which of the following processor features is used to dynamically reduce power consumption based on current operating conditions?

Throttling

You're responsible for ordering consumables for your organization's printers. These printers are heavily utilized by users who demand the utmost reliability. Which of the following would be the best option when ordering new toner for these printers?

Toner cartridges recommended by the printer manufacturer.

What type of peripheral device is typically found on a notebook computer and allows the user to control the cursor with a finger?

Touch pad

You have a laser printer that has worked fine until today. Now whenever anything is printed, only blank pages come out. Which part are you most likely to replace?

Transfer corona

What security measure uses a unique key that can be used for hardware system ID?

Trusted Platform Module (TPM)

What is the most common interface for peripheral devices?

USB

Which connector is most commonly used by modern printers to connect to desktop PC systems?

USB

You would like to add additional HDD storage to your notebook computer. Which of the following connection types are you most likely to use?

USB

which connector is most commonly used to connect printers to desktop PC systems?

USB

What standard provides for data transfer rates up to 480Mbps with a maximum cable length of 5 meters?

USB 2.0

Which of the following standards provides for data transfer rates up to 480 MBps with a maximum cable length of 5 meters?

USB 2.0

Which of the following standards provides for data transfer rates up to 480 Mbps with a max cable length of 5 meters?

USB 2.0

What category do apps fall into if they have not been reviewed, approved, and signed with a certificate?

Untrusted

You need to create a user account on a Windows system that can create files, run applications, and install printers when the driver for the printer already exists on the computer. You want the user to have only the minimum rights necessary on the computer. Which group should this user be a member of

Users

You are looking at a high-density (three-row) female DB-15 connector on the computer. What device uses this connector?

VGA/SVGA monitors

Recently, a Windows 10 update was automatically downloaded and installed on your Windows 10 system. However, after installing the update, your contact manager database application no longer works correctly. You want to uninstall the latest updates to see if the application starts working again.

View your update history

Which of the following protocols carry phone calls over an IP-based network?

VoIP

What is the difference between UXGA and WUXGA displays?

WUXGA has a widescreen aspect ratio

You place a new disc in an optical drive then double-click the drive in the operating system's file browser interface. An error message appears stating that the drive is not accessible. What should you do?

Wait. Then try again

Closed source and second least popular mobile device operating system

Windows

Device manufacturers include Microsoft, Samsung, and HTC

Windows

You are unable to read the disk. What is most likely the problem?

Windows 98 does not support NTFS

Which of the following situations is most likely to require a system BIOS update?

You are upgrading a processor

Which one of the following situations is most likely to require a system BIOS upgrade?

You are upgrading a processor

Your organization has 20 employees who need an accounting software update installed. Due to a miscommunication, the purchaser only paid to update 10 licenses. The software company issued a "paper license" and a single key for updating 10 users. Since this is an enterprise paper license there is no mechanism that enforces a limit to the number of times the key can be used so you decide to go ahead and update all 20 users. What are the possible consequences of this decision?

You risk losing your job. You expose your company to litigation by violating the software license agreement.

Which of the following conditions would prevent you from GUID Partition Table (GPT) whcn setting up a disk drive?

You're setting up the drive to boot Windows 7 on a computer that uses traditional BIOS If you need the drive to boot Windows and the computer uses traditional BIOS (not UEFI), you need to set up the drive with MBR. A GPT drive can -Be basic or dynamic -Set up to boot 64-bit Windows 7 on a UEFI-based computer -Be used to create up to 128 partitions

What should you do if a LAN adapter fails and you are unable to connect the computer to the network?

add a network card using a PCI slot

Portable devices have a software-controlled switch that disables all wireless functionality. What is the name of this software-controlled switch?

airplane mode

At what rate will two PC-2400 DDR modules operate?

all memory will operate at 300 MHz

You're using a Linux distribution that uses Debian Package Manager (dpkg) for package management. Which command would you use to install httpd, the Apache HTTP Server package, and all its dependencies?

apt-get install httpd

What utility checks the disk for bad clusters?

chkdsk

What utility would you use to correct cross-linked clusters within the file system on a Windows workstation?

chkdsk

You want to upgrade all memory in your system with the fastest memory available. What should you choose?

choose the type of memory that is supported by your motherboard

What is inserted in an AMR slot to provide sound functions?

daughterboard

What Windows utilities would you use to realign the file structure on the disk to optimize performance?

defrag

What Windows utility would you use to realign the file structure on the disk to optimize performance?

defrag

You replace a sound card installed in a PCI slot with a sound card on the motherboard? What should you do if there is no sound after you reboot?

edit the CMOS settings and enable the onboard sound

What is installed between the system case and the motherboard back panel I/O ports?

faceplate

What is the function of the chipset on the motherboard?

facilitate communication between the processor, memory components, and peripheral devices

What should you do when you upgrade your processor but nothing on your screen is shown or starts?

flash the BIOS

Which tool would you use to configure the drive to use the FAT32 file system?

format

Which utility will you most likely use to solve the problem?

format

Connects segments on the same subnet. Repeats signals out to all other ports

hub

What is a DB-15 connector on a sound card typically used for?

joystick and MIDI port

What should you do if the BIOS recognizes only one memory module after installing two?

make sure both modules are seated properly in their slots

What should you do when there are no sound or lights on after you press the power button?

make the power button is connected to the motherboard

Which port should you use to connect a non-amplified microphone to a sound card?

mic in

Form factor - portable desktop computer

micro-ATX

What features are typically available through TRS ports on a sound card?

microphone in and speaker out

What functions are associated with an AMR riser card?

modem and audio

What kind of power connector is used on PATA (IDE) internal hard disk drives and optical drives?

molex

Which of the following characteristics accurately describe passive heat sinks

more reliable than active heat sinks.

How can you configure power supply to receive different voltage level?

move power switch on the power supply to the different voltage

What should you do when your memory is not configured to run dual channel mode?

move the modules to the correct motherboard slot

What should you do so your computer is compatible with electrical power in Europe?

move the switch on the power supply to a different voltage

What is the most common method for removing RAM from a motherboard?

move the tabs holding the RAM out of the way; pull straight up to remove the RAM

What term refers to placing to processors on a single processor chip or die?

multi-core

What is a characteristic of a multi-processor system?

multiple processor sockets on the motherboard

What will most likely contain SODIMM memory?

notebook computers

What component will you have to upgrade if you upgrade your processor?

operating system

What error detection technique can detect errors with only one bit

parity

What is true about the relative performance of an AMD and an Intel processor?

performance will depend on other factors such as cache and other features

Which command would you use to display a simple list of all processes running on a Linux distribution that uses either RPM or dpkg for package management?

ps -e

What is the role of the CMOS in a modern computer?

saves information about system devices

You want to scan your system for changed system files and automatically revert to previous versions for any file that has been altered. You want the scan to run once the next time the system boots. Which command should you use?

sfc /scanonce

Connects segments on the same subnet. Forwards signals to only the port connected to the destination device

switch

Operate in full-duplex mode, meaning devices can both send and receive data at the same time

switch

What the most likely problem if the computer hangs after asking you current time and date?

the CMOS battery failed

What is the biggest advantage of 64-bit processors over 32-bit processors?

the ability to use over 4GB of memory

What processor feature is used to dynamically reduce power consumption based on current operating conditions?

throttling

You are the network administrator of a branch office of your company. The branch office network is part of a WAN that covers most of the United States. Users have been complaining that they are unable to access resources over the WAN at the main headquarters. You suspect that one of the routers between your office and the main headquarters is not working properly. What TCP/IP utility can you use to see if a router is not working properly?

tracert

What 2 components are found in dot matrix printers?

tractor feed // platen

What should you do if you are unsure if your power supply can support additional components?

upgrade to a power supply that provides more watts

What do you do if have PCIe 8-connector video card but your power supply doesn't have the connector?

use an adapter cable to connect two 4-pin Molex connectors to the 8-pin PCIe connector

What situation is most likely to require a system BIOS upgrade?

you are upgrading a processor

You're using a Linux distribution that uses RPM for package management. Which command would you use to install httpd, the Apache HTTP Server package, and all its dependencies?

yum install httpd

You're using a Linux distribution that uses RPM for package management. Which command would you use to display a list of all packages available for installation withing the Internet repositories configured on this system?

yum list available

You're using a Linux distribution that uses RPM for package management. Which command would you use to check to see if the httpd package, the Apache HTTP Server package, is installed?

yum list intalled httpd


Related study sets

Split-Circuits+Multi-wire circuits

View Set

CNET 101 - Computer User Support I - Midterm Exam (Chapters 1-3)

View Set