Assembly and Rigging Prepware
78. (8289)-(Refer to Figure 9.) When the outside air temperature is 80°F, select the acceptable 3/16 cable tension range.
B. 117 pounds minimum, 143 pounds maximum.
44. (8255)-Where is fuselage station No. 137 located?
B. 137 inches aft of the zero or fixed reference line.
63. (8274)-With which system is differential control associated?
B. Aileron.
26. (8237)-Washing-in the left wing of a monoplane, for purposes of rigging corrections after flight test, will have what effect on the lift and drag of that wing?
B. Both drag and lift will increase due to increased angle of attack.
20. (8231)-An airplane which has good longitudinal stability should have a minimum tendency to?
B. Pitch
80. (8291)-Why is it generally necessary to jack an aircraft indoors for weighing?
B. So that air currents do not destabilize the scales.
31. (8242)-What physical factors are involved in the aspect ratio of airplane wings?
B. Span and chord.
72. (8283)-If the travel of an airplane's controls is correct but the cables are rigged exceptionally tight, what probable effect will this have when flying the airplane?
B. The airplane will be heavy on the controls.
70. (8281)-Movement of the cockpit control toward the nosedown position during a ground operational check of the elevator trim tab system will cause the trailing edge of the trim tab to move in which direction?
B. Upward regardless of elevator position.
22. (8233)-The angle of incidence is that acute angle formed by?
B. a line parallel to the wing chord and a line parallel to the longitudinal axis of the aircraft.
30. (8241)-When the lift of an airfoil increases, the drag will?
B. also increase.
36. (8247)-Buffeting is the intermittent application of forces to a part of an airplane. It is caused by?
B. an unsteady flow from turbulence.
45. (8256)-Proper wing twist in a sheet metal constructed wing can usually be checked by utilizing a?
B. bubble level and special fixtures described by the manufacturer.
14. (8225)-Movement about the longitudinal axis (roll) in a helicopter is effected by movement of the?
B. cyclic pitch control.
15. (8226)-Movement about the lateral axis (pitch) in a helicopter is effected by movement of the?
B. cyclic pitch control.
57. (8268)-Placing a piece of cloth around a stainless steel control cable and running it back and forth over the length of the cable is generally a satisfactory method of?
B. inspecting for broken strands.
25. (8236)-The elevators of a conventional airplane are used to provide rotation about the?
B. lateral axis.
67. (8278)-Stability about the axis which runs parallel to the line of flight is referred to as?
B. lateral stability.
52. (8263)-When a fiber or nylon insert-type, self-locking nut can be threaded on a bolt or stud through the insert with only the fingers, it should be?
B. rejected.
23. (8234)-An airplane's center of lift is usually located aft of its center of gravity?
B. so that the airplane will have a nose-heavy tendency.
38. (8249)-The primary purpose of stall strips is to?
B. stall the inboard portion of the wings first.
3. (8214)-A reduction in anti-torque thrust will cause the?
B. tail to pivot in the direction of torque rotation around the main rotor axis.
59. (8270)-Very often, repairs to a control surface require static rebalancing of the control surface. Generally, flight control balance condition may be determined by?
B. the behavior of the trailing edge when the surface is suspended from its hinge points.
79. (8290)-Differential control on an aileron system means that?
B. the up travel is more than the down travel.
19. (8230)-If the vertical fin of a single-engine, propeller-driven airplane is rigged properly, it will generally be parallel to?
B. the vertical axis but not the longitudinal axis.
55. (8266)-What is the smallest size cable that may be used in aircraft primary control systems?
C. 1/8 inch.
76. (8287)-(Refer to Figure 8.) Identify the cable that is used in primary control systems and in other places where operation over pulleys is frequent.
C. 3.
61. (8272)-Fairleads should never deflect the alignment of a cable more than?
C. 3°.
43. (8254)-Where is the buttock line or buttline of an aircraft?
C. A width measurement left or right of, and parallel to, the vertical centerline.
42. (8253)-Where would you find precise information to perform a symmetry alignment check for a particular aircraft?
C. Aircraft service or maintenance manual.
50. (8261)-Which is an acceptable safety device for a castle nut when installed on secondary structures?
C. Cotter pin.
64. (8275)-Which statement concerning the 100-hour inspection of an airplane equipped with a push-pull tube-type control system is true?
C. The threaded rod ends should be checked for the amount of thread engagement by means of the inspection hole provided.
1. (8212)-The auxiliary (tail) rotor of a helicopter permits the pilot to compensate for and/or accomplish which of the following?
C. Torque and directional control.
12. (8223)-Which statement is correct concerning torque effect on helicopters?
C. Torque direction is the opposite of rotor blade rotation.
10. (8221)-Main rotor blades that do not cone by the same amount during rotation are said to be out of?
C. Track
47. (8258)-What nondestructive checking method is normally used to ensure that the correct amount of swaging has taken place when installing swaged-type terminals on aircraft control cable?
C. Use a terminal gauge to check the diameter of the swaged portion of the terminal.
5. (8216)-The acute angle formed by the chord line of a wing and the relative wind is known as the?
C. angle of attack.
37. (8248)-Movement of an airplane along its lateral axis (roll) is also movement?
C. around or about the longitudinal axis controlled by the ailerons.
46. (8257)-The vast majority of aircraft control cables are terminated with swaged terminals, that must be?
C. checked with a go-no-go gauge before and after, to show compliance with the manufacturer's requirements after the swaging operation.
75. (8286)-The universal propeller protractor can be used to measure?
C. degrees of flap travel.
35. (8246)-The angle of incidence of an airplane at rest?
C. does not change when in flight.
71. (8282)-If the control stick of an aircraft with properly rigged flight controls is moved forward and to the right, the left aileron will move?
C. down and the elevator will move down.
69. (8280)-If the control stick of an aircraft with properly rigged flight controls is moved rearward and to the left, the right aileron will move?
C. down and the elevator will move up.
29. (8240)-The chord of a wing is measured from A. wingtip to wingtip. B. wing root to the wingtip. C. leading edge to trailing edge.
C. leading edge to trailing edge.
9. (8220)-If a single-rotor helicopter is in forward horizontal flight, the angle of attack of the advancing blade is?
C. less than the retreating blade.
21. (8232)-As the angle of attack of an airfoil increases, the center of pressure will?
C. move toward the leading edge.
77. (8288)-A tension regulator in the flight control cable system of a large all-metal aircraft is used primarily to?
C. retain a set tension.
48. (8259)-When inspecting a control cable turnbuckle for proper installation, determine that?
C. the safety wire ends are wrapped a minimum of four turns around the terminal end shanks.
4.(8215)-In rotorcraft external-loading, the ideal location of the cargo release is where the line of action passes?
C. through the center of gravity at all times.
6. (8217)-A helicopter in forward flight, cruise configuration, changes direction by?
C. tilting the main rotor disk in the desired direction.
56. (8267)-After repairing or re-covering a rudder, the surface should be rebalanced?
C. to manufacturer's specifications.
40. (8251)-The correct dihedral angle can be determined by?
C. using a dihedral board and bubble level along the front spar of each wing.
8. (8219)-In a hovering helicopter equipped with a tail rotor, directional control is maintained by?
C. varying the pitch of the tail rotor blades.
39. (8250)-Rigging and alignment checks should not be undertaken in the open; however, if this cannot be avoided, the aircraft should be positioned?
C. with the nose into the wind.
17. (8228)-Other than the manufacturer maintenance manual what other document could be used to determine the primary flight control surface deflection for an imported aircraft that is reassembled after shipment?
A. Aircraft type certificate data sheet.
62. (8273)-Where does the breakage of control cable wires occur most frequently?
A. Breakage usually occurs where cables pass over pulleys and through fairleads.
51. (8262)-When used in close proximity to magnetic compasses, cotter pins are made of what material?
A. Corrosion resisting steel.
27. (8238)-What type of flap system increases the wing area and changes the wing camber? A. Fowler flaps.
A. Fowler flaps.
81. (8292)-Which should be accomplished before jacking an aircraft?
A. Install critical stress panels or plates.
13. (8224)-What is the purpose of the free-wheeling unit in a helicopter drive system?
A. It disconnects the rotor whenever the engine stops or slows below the equivalent of rotor RPM.
54. (8265)-How are changes in direction of a control cable accomplished?
A. Pulleys.
28. (8239)-If the right wing of a monoplane is improperly rigged to a greater angle of incidence than designated in the manufacturer's specifications, it will cause the?
A. airplane to be off balance both laterally and directionally.
68. (8279)-The purpose of spring tabs or servo tabs is to?
A. assist the pilot in moving the control surfaces.
11. (8222)-One purpose of the freewheeling unit required between the engine and the helicopter transmission is to?
A. automatically disengage the rotor from the engine in case of an engine failure.
2. (8213)-The vertical flight of a helicopter is controlled by?
A. collective pitch changes.
58. (8269)-The cable-operated control system of an all-metal aircraft, not incorporating a temperature compensating device, has been rigged to the correct tension in a heated hangar. If the aircraft is operated in very cold weather, the cable tension will?
A. decrease when the aircraft structure and cables become cold.
53. (8264)-The purpose of the vertical fin is to provide?
A. directional stability.
73. (8284)-During inspection of the flight control system of an airplane equipped with differential-type aileron control, side-to-side movement of the control stick will cause?
A. each aileron to have a greater up travel (from the streamlined position) than down travel.
41. (8252)-The dihedral angle of a wing may be measured by placing a straightedge and level protractor on the?
A. front spar.
18. (8229)-If a pilot reports that an airplane flies left wing heavy, this condition may be corrected by?
A. increasing the angle of incidence of the left wing, or decreasing the angle of incidence of the right wing, or both.
32. (8243)-Improper rigging of the elevator trim tab system will affect the balance of the airplane about its?
A. lateral axis.
16. (8227)-Wing dihedral, a rigging consideration on most airplanes of conventional design, contributes most to stability of the airplane about its?
A. longitudinal axis.
66. (8277)-Aircraft flight control trim systems must be designed and installed so that the?
A. pilot can determine the relative position of the trim tab from the cockpit.
33. (8244)-An airplane that has a tendency to gradually increase a pitching moment that has been set into motion has?
A. poor longitudinal stability.
60. (8271)-Excessive wear on both of the sides of a control cable pulley groove is evidence of?
A. pulley misalignment.
34. (8245)-The purpose of wing slats is to?
A. reduce stalling speed.
7. (8218)-The purpose in checking main rotor blade tracking is to determine the?
A. relative position of the blades during rotation.
24. (8235)-An airplane is controlled directionally about its vertical axis by the?
A. rudder.
49. (8260)-If all instructions issued by the swaging tool manufacturer are followed when swaging a cable terminal, the resultant swaged terminal strength should be?
A. the full rated strength of the cable.
74. (8285)-A universal propeller protractor used to measure the degrees of aileron travel should be zeroed?
A. with the aileron in the NEUTRAL position.
65. (8276)-If control cables are adjusted properly and the control surfaces tend to vibrate, the probable cause is?
A. worn attachment fittings.