Chapter 8 Quiz Study Guide 2

Ace your homework & exams now with Quizwiz!

19.Which IPv6 address is most compressed for the full FE80:0:0:0:2AA:FF:FE9A:4CA3 address? FE80::2AA:FF:FE9A:4CA3 FE80::0:2AA:FF:FE9A:4CA3​FE80:::0:2AA:FF:FE9A:4CA3​FE8::2AA:FF:FE9A:4CA3​

FE80::2AA:FF:FE9A:4CA3

23.What is the prefix length notation for the subnet mask 255.255.255.224?

/27

3.What are three parts of an IPv6 global unicast address? (Choose three.) a subnet ID that is used to identify networks inside of the local enterprise site an interface ID that is used to identify the local host on the network a global routing prefix that is used to identify the network portion of the address that has been provided by an ISP an interface ID that is used to identify the local network for a particular host a global routing prefix that is used to identify the portion of the network address provided by a local administrator

1. a subnet ID that is used to identify networks inside of the local enterprise site 2. an interface ID that is used to identify the local host on the network 3. a global routing prefix that is used to identify the network portion of the address that has been provided by an ISP

8.The decimal equivalent of the binary number 10010101 is

149

6.A DHCP server is used to assign IP addresses dynamically to the hosts on a network. The address pool is configured with 192.168.10.0/24. There are 3 printers on this network that need to use reserved static IP addresses from the pool. How many IP addresses in the pool are left to be assigned to other hosts? 251 253 252 254

251

9.How many bits are in an IPv4 address? 32 256 128 64

32

11.Fill in the blank. What is the decimal equivalent of the hex number 0x3F?

63

When a Cisco router is being moved from an IPv4 network to a complete IPv6 environment, which series of commands would correctly enable IPv6 forwarding and interface addressing? Router# configure terminalRouter(config)# interface fastethernet 0/0Router(config-if)# ip address 192.168.1.254 255.255.255.0Router(config-if)# no shutdownRouter(config-if)# exitRouter(config)# ipv6 unicast-routing Router# configure terminalRouter(config)# interface fastethernet 0/0Router(config-if)# ipv6 address 2001:db8:bced:1::9/64Router(config-if)# no shutdownRouter(config-if)# exitRouter(config)# ipv6 unicast-routing Router# configure terminalRouter(config)# interface fastethernet 0/0Router(config-if)# ipv6 address 2001:db8:bced:1::9/64Router(config-if)# no shutdownRouter# configure terminalRouter(config)# interface fastethernet 0/0Router(config-if)# ip address 2001:db8:bced:1::9/64Router(config-if)# ip address 192.168.1.254 255.255.255.0Router(config-if)# no shutdown Router# configure terminalRouter(config)# interface fastethernet 0/0

B) Router# configure terminal Router(config)# interface fastethernet 0/0 Router(config-if)# ipv6 address 2001:db8:bced:1::9/64 Router(config-if)# no shutdown Router(config-if)# exit Router(config)# ipv6 unicast-routing

Which message is displayed on the web server? Correct configuration! IPv6 address configured! You did it right! Successful configuration!

Correct configuration!

1.What is indicated by a successful ping to the ::1 IPv6 address? IP is properly installed on the host. The link-local address is correctly configured. The default gateway address is correctly configured. The host is cabled properly. All hosts on the local link are available.

IP is properly installed on the host.

5.Which two statements are correct about IPv4 and IPv6 addresses? (Choose two.) IPv4 addresses are 32 bits in length. IPv6 addresses are represented by hexadecimal numbers. IPv6 addresses are 32 bits in length. IPv4 addresses are 128 bits in length. IPv4 addresses are represented by hexadecimal numbers. IPv6 addresses are 64 bits in length.

IPv4 addresses are 32 bits in length. IPv6 addresses are represented by hexadecimal numbers.

14.What two statements describe characteristics of Layer 3 broadcasts? (Choose two.) Routers create broadcast domains A limited broadcast packet has a destination IP address of 255.255.255.255 There is a broadcast domain on each switch interface. A router will not forward any type of Layer 3 broadcast packet. Broadcasts are a threat and users must avoid using protocols that implement them. Some IPv6 protocols use broadcasts.

Routers create broadcast domains A limited broadcast packet has a destination IP address of 255.255.255.255

10.An IPv6 enabled device sends a data packet with the destination address of FF02::1. What is the target of this packet? all IPv6 enabled nodes on the local link all IPv6 configured routers across the network all IPv6 configured routers on the local link all IPv6 DHCP servers

all IPv6 enabled nodes on the local link

22.A message is sent to all hosts on a remote network. Which type of message is it? directed broadcast limited broadcast unicast multicast

direct broadcast

13.What are two types of IPv6 unicast addresses? (Choose two.) loopback link-local anycast multicast

loopback link-local

Which two parts are components of an IPv4 address? (Choose two.)

network portion host portion

2.Which two ICMP messages are used by both IPv4 and IPv6 protocols? (Choose two.) route redirection protocol unreachable router solicitation neighbor solicitation router advertisement

route redirection protocol unreachable

4.When an IPv6 enabled host needs to discover the MAC address of an intended IPv6 destination, which destination address is used by the source host in the NS message? solicited-node multicast address global unicast address of the receiver all-node multicast address link-local address of the receiver

solicited-node multicast address

12.Which network migration technique encapsulates IPv6 packets inside IPv4 packets to carry them over IPv4 network infrastructures? tunneling encapsulation translation dual-stack

tunneling

15.When will a router drop a traceroute packet? when the value in the TTL field reaches zero when the router receives an ICMP Time Exceeded message when the host responds with an ICMP Echo Reply message when the values of both the Echo Request and Echo Reply messages reach zero when the RTT value reaches zero

when the value in the TTL field reaches zero

7.Which two things can be determined by using the ping command? (Choose two.) whether or not the destination device is reachable through the network the average time it takes a packet to reach the destination and for the response to return to the source the average time it takes each router in the path between source and destination to respond the IP address of the router nearest the destination device the number of routers between the source and destination device

whether or not the destination device is reachable through the network the average time it takes a packet to reach the destination and for the response to return to the source


Related study sets

Chapter 33: Abuse in the Family and Community

View Set

Conflict management com4462 Study Guide

View Set

Neuromuscular and Nervous Systems

View Set

6th Grade Geography - Mayan, Incan and Aztec Civilizations

View Set

Theology 2: Chapter 2 Part A Test

View Set

Respiratory System L2 Inhalation & Exhalation

View Set

EASA Part 66 : Maintenance Practice Question3

View Set