Comptia A+ 220-1001

Ace your homework & exams now with Quizwiz!

Match the IPV4 Addresses to the Address Type: CLASS A? A. 12.174.25.98 B. 12.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

A. 12.174.25.98

An employee at Dion Training complains that their smartphone is broken. They state that it cannot connect to the internet, nor can it make or receive phone calls and text messages. You ask them to start up the music player on his phone, and it opens without any issues. It appears the common issue has to do with the device's network connectivity. Which of the following is MOST likely the problem with this smartphone? A.Airplane mode is enabled on the device B.The Bluetooth connection is disabled C.The VPN password was entered incorrectly D.The cellular radio in it is broken

A. Airplane mode is enabled on the device

You are configuring a SOHO network and only denying specific IP addresses from accessing the network while allowing any IP addresses not found on the list. Which of the following should be implemented? A.Blocklist B.Allow list C.MAC filtering D.Port forwarding

A. Blocklist

You are troubleshooting a laser printer and noticed the paper's image has a white streak running across the face of the paper. Which of the following should be performed to fix this issue? A.Clean the printer's corona wires B.Clean the printer's fusing assembly C.Replace the toner cartridge D.Replace the printer's drum

A. Clean the printer's corona wires A corona wire is a charged wire in a laser printer that draws the toner off the drum onto the paper. It must be cleaned when the toner cartridge is replaced. A dirty corona wire can cause a portion of the drum not to be charged properly and lead to a white streak appearing on the printed image.

You have been asked to install a network cable inside a conduit placed underground and connected to two buildings located about 1 KM apart. Which of the following cable types should you choose? A.Fiber B.Coaxial C.Shielded D.Plenum

A. Fiber If you are dealing with connecting two networks over a long distance (over a few hundred meters), you should use a fiber optic cable. Shielded and plenum copper cables can only cover a distance of approximately 100 meters in length. Coaxial cables can cover a maximum distance of 200 to 500 meters in length.

(This is a simulated PBQ. If you had this question on the real exam, you would be asked to drag-and-drop a label with the component's name onto the proper location on the port cluster.) Using the image above, which of the following correctly indicates the port labeled as H? A.FireWire B.SATA C.USB 3.0 D.DVI

A. FireWire FireWire is a serial SCSI connection that uses a D-shaped connector that supports up to 800 Mbps of bandwidth

You have been asked to install a network cable in the crawl space between the ceiling in your office and the roof. You need to choose the right type of cable to ensure you do not violate the local fire codes. Which of the following cable types should you choose? A.Plenum B.Fiber C.Shielded D.Coaxial

A. Plenum Plenum-rated cable has a special insulation that has low smoke and low flame characteristics. Plenum cable is mandated to be installed in any air handling space.

You have just finished building a Windows server, installing its operating system, updating its security patches, formatting a dedicated data partition, and creating accounts for all of the company's employees. What is the next thing that must be configured to provide users with the ability to access large multifunction devices across the network? A.Print server B.RAID storage C.Audit logging D.File sharing

A. Print server

What describes how many times the image on the monitor changes per second? A.Refresh rate B.Resolution C.Aspect ratio D.Frame rate

A. Refresh rate

Dion Training has a single switch that services every room within its offices. The switch contains 48 ports, but Jason wants to divide the ports based on functional areas, such as web development, instruction support, and administration. Which technology should Jason utilize to divide the physical switch into three logically divided areas? A.VLAN B.VPN C.DSL D.NAT

A. VLAN A VLAN (virtual LAN) allows a single physical switch to be divided into logical networks. VLANs are only supported on managed switches, but they allow for a different logical subnetwork address to be assigned to various ports on the switch. This requires that communications between different VLANs must go through a router, just as if you had multiple switches.

When using a Type 1 hypervisor virtualized environment, which of the following hardware types is necessary to connect the VMs to the corporate network? A.Virtual NIC B.VNC C.VPN D.VDI

A. Virtual NIC A virtual machine includes a virtual NIC. A virtual NIC is a type of virtual adapter that can be configured on logical partitions to provide a network interface. This virtual NIC can be paired and mapped to a physical NIC to get the VM onto the network.

Which of the following operating systems has the built-in capability to install and run Hyper-V? A.Windows 10 B.Windows 2000 C.Windows 7 DWindows XP

A. Windows 10 Hyper-V can be run natively on Windows servers (2008, 2012, 2016, and 2019) and desktops (8, 8.1, and 10). Hyper-V is a Microsoft technology that allows users to create virtual computer environments and run and manage multiple operating systems on a single physical server or computer.

Ted, a file server administrator at Dion Training, has noticed that many sensitive files have been transferred from a corporate workstation to an IP address outside of the local area network. Ted looks up the IP address and determines that it is located in a foreign country. Ted contacts his company's security analyst, verifying that the workstation's anti-malware solution is up-to-date and the network's firewall is properly configured. What type of attack most likely occurred to allow the exfiltration of the files from the workstation? A. Zero-day B. Session hijacking C. MAC spoofing D. Impersonation

A. Zero-day, Since the firewall is properly configured and the anti-malware solution is up-to-date, this signifies that a zero-day vulnerability may have been exploited

A computer technician is configuring a NAS for a company to store their corporate data. The technician has installed four 10 TB hard drives operating at 5400 RPM in a RAID 10 configuration. How much usable storage space is contained in this NAS? A.20 TB B.40 TB C.10 TB D.30 TB

A.20 TB A RAID 10 combines disk mirroring and disk striping to protect data stored in the array and required a minimum of four disks. Since the NAS uses a RAID 10 configuration, it is a stripped and mirrored array.

Which cellular technology utilizes new frequency bands to reach proposed speeds of up to 70 Gbps? A.5G B.3G C.LTE D.4G

A.5G 5G cellular technology is made up of three different types: low-band, mid-band, and high-band mmWave technology. Low-band 5G reaches an average speed of 55 Mbps with a theoretical speed of 150 Mbps.

You have just finished installing a virtual machine on a workstation. Your boss asks you to install a second virtual machine with the same settings. To save time, which of the following functions should you use? A.Cloning B.Migration C.Secure Copy D.Shadow Copy

A.Cloning

The large multi-function network printer has recently begun to print pages that appear to have a dust-like coating when handled by the users. Which of the following components should be replaced based on this description? A.Fuser B.Scanner assembly C.Drum D.Toner cartridge

A.Fuser The printer passes the paper through the fuser, a pair of heated rollers. As the paper passes through these rollers, the loose toner powder melts, fusing with the paper's fibers. The fuser rolls the paper to the output tray, and you have your finished page. The fuser also heats the paper itself, of course, which is why pages are always hot when they come out of a laser printer or photocopier.

Which of the following cables was a proprietary cable used in many iPhones and iPads? A.Lightning B.Mini USB C.Micro USB D.USB-C

A.Lightning

Dion Training has asked you to consult on the installation of their new file server. The current server consists of a RAID 5 array with three 1 TB 7200 RPM hard disk drives. Due to the increased reliance on the new file server, you have been asked to recommend a RAID solution that will help ensure there is no unscheduled downtime, no data loss, and increase speed/performance over the current file server. Based on these requirements, which of the following RAID solutions should you recommend? A.RAID 10 B.RAID 5 C.RAID 0 D.RAID 1

A.RAID 10 A RAID 10 is the best solution to meet all of these requirements since it provides a fully redundant RAID with both the advantages of mirroring and disk striping.

Jason, a computer technician, is troubleshooting a motherboard. He has determined that the motherboard needs to be replaced in the laptop. Which of the following next step should be performed next? (Choose TWO) A.Read owners' manual for procedures and steps to avoid breaking the warranty B.Documentation of all screws and locations C.Disconnect laptop keyboard before disconnecting the battery D.Use portable power driver to remove screws

A.Read owners' manual for procedures and steps to avoid breaking the warranty B.Documentation of all screws and locations

A client has a new 2-in-1 laptop/tablet. Whenever they use the touchscreen, the cursor appears to jump to the wrong location and select the wrong icons. If the client connects a USB mouse, there are no issues with using the device. Which of the following should you attempt to perform FIRST to fix this issue? A.Recalibrate the touchscreen B.Update the touchscreen's driver C.Reinstall Windows 10 D.Disable the touchscreen

A.Recalibrate the touchscreen Tablet/laptops with touchscreen capability can be recalibrated from within the Windows Control Panel.

Which of the following virtualization concepts refers to a VM's ability to have memory allocated for its use? A.Resource pooling B.Measured service C.Virtual application streaming D.Synchronization

A.Resource pooling Resource pooling refers to the concept that allows a virtual environment to allocate memory and processing capacity for a VMs use.

Tom is running some new Cat 5e cabling in an office building to connect a few offices. The ceiling is constructed as a drop ceiling with fluorescent lights and does not have any cable trays. Due to the proximity of the fluorescent lights to the cable being run, what type of CAT 5e cable should be run? A.STP B.Fiber C.UTP D.Coaxial

A.STP STP (Shielded Twisted Pair) is a type of cabling that can help prevent electrical interferences or cross-talk.

Which of the following devices commonly use an ARM-based processor? (Select TWO) A.Tablet B.Smartphone C.Laptop D.Desktop

A.Tablet B.Smartphone

Match the IPV4 Addresses to the Address Type: Loopback? A. 12.174.25.98 B. 127.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

B. 127.0.0.1

You are troubleshooting a customer's PC. You realize there is a problem with the RAM and decided to replace the faulty module. You turn on the PC, and after a few seconds, you hear a single beep. What does hearing a single beep indicate? A.BIOS detected an error B.BIOS completed POST C.CMOS battery needs to be replaced D.Possible faulty RAM module

B. BIOS completed POST During the bootup process, a power-on self-test (POST) is performed. A single beep is commonly used to indicate the successful completion of the POST.

A client's PC was not able to be powered on. You are troubleshooting the issue by ensuring that the power cable is connected firmly to both the PC and the wall outlet. You took the PC to your workbench to diagnose it. You tried powering on the PC at the workbench, but it did not work. You decided to test the power supply unit and ensure it was selected for 110 volts. You connected it to a power supply tester and verified the power supply is working properly. What is the NEXT step in troubleshooting you should perform? A.Replace the memory B.Check the power connection to the motherboard C.Pull the CMOS battery out and wait 5 min and try again D.Replace the power supply

B. Check the power connection to the motherboard

You are about to embark on a long trip, which will require over 24 hours of flying. You want to read several books during your trip, but do not want to carry all the paperbacks with you. You have decided to purchase a device for the trip for the sole purpose of reading books, but it must have extremely long battery life and not get distorted or hard to read in the sunlight. Which should you purchase? A. Smartphone B. E-reader C. Tablet D. Laptop

B. E-reader

What is the name of a computer system that is designed to perform a specific and dedicated function? A.Patch system B.Embedded system C.UTM system D.Legacy system

B. Embedded system An embedded system is a computer system designed to perform a specific, dedicated function. These systems can be as small and simple as a microcontroller in an intravenous drip-rate meter or as large and complex as an industrial control system managing a water treatment plant. Embedded systems might typically have been designed to operate within a closed network. The network elements are all known to the system vendor, and there is no connectivity to wider computer data networks.

You are troubleshooting a computer that will not boot. After gathering information from the client about the symptoms they have experienced, you believe the power supply may be faulty. You used a power supply tester to determine if the power supply provides the right amount of output voltage and has determined the power supply is only providing 50% of the voltage that it is supposed to provide to the workstation. What is the next step you should perform according to the CompTIA troubleshooting methodology? A.Establish a theory of probable cause (question the obvious) B.Establish a plan of action to resolve the problem and then implement the solution C.Identify the problem D.Verify full system functionality and, if applicable, implement preventative measures

B. Establish a plan of action to resolve the problem and then implement the solution

Which of the following cloud computing resources are MOST important when determining a cloud file-storage synchronization application's performance? A.Disk speed B.I/O bandwidth C.RAM utilization D.CPU utilization

B. I/O bandwidth I/O bandwidth is the measurement of the amount of input and output operations that can be performed within a given time. The higher the I/O bandwidth, the faster and more efficient a cloud file-storage synchronization application will become. Applications that rely on large amounts of reading and writing of data require a high amount of I/O bandwidth.

You have been dispatched to a customer's office to help them fix their printer. You have asked the customer what the issue is, and the customer states, "The printer will not work." You ask a few follow-up questions to understand the situation better and ask if any error messages were displayed. Which of the following steps of the CompTIA troubleshooting methodology best describes the actions you are currently taking? A.Establish a plan of action to resolve the problem and then implement the solution B.Identify the problem C.Verify full system functionality and, if applicable, implement preventative measures D.Test the theory to determine the cause

B. Identify the problem

Dion Training has decided to use a PaaS solution to host their training courses. The service charges are based on the number of students enrolled in the courses each month. Which type of cloud computing concept is being demonstrated by this pricing strategy? A.Synchronization apps B.Metered service C.Rapid elasticity D.Resource pooling

B. Metered service Resources are measured through metering on a per-use basis. The metering measurement is based on the type of resources such as storage, processing, bandwidth, or active users. The metering mechanism should be accessible to the customer via a reporting dashboard, providing complete transparency in usage and billing. Metered services are pre-paid, a-la-carte, pay-per-use, or committed offerings. A metered service like a database may charge its users based on the actual usage of the service resources on an hourly or monthly basis.

You want to build a virtualization workstation that will be used to run four different server operating systems simultaneously to create a test lab environment. Each guest operating system only requires 20 GB of storage on the host workstation. Which of the following is the MOST important piece of hardware needed for this system to run efficiently? A.ATX motherboard B.Multi-core processor C.Dedicated GPU D.5400 RPM hard disk drive

B. Multi-core processor

A user wants to print a spreadsheet horizontally on a piece of paper instead of vertically to fit more columns on a single page. What setting should the user enable on the printer for this print job to achieve this result? A.Collate B.Orientation C.Duplex D.Transparency

B. Orientation By default, Microsoft Excel prints worksheets in portrait orientation (taller than wide). You can change the page orientation to landscape on a worksheet-by-worksheet basis. Page orientation is how a rectangular page is oriented for normal viewing.

You see some fading across your papers when printing things using a laser printer. The black color appears to be more faded than the other colors on your documents. What is the BEST solution to this problem? A. Increase the temperature of the fuser element B. Replace the toner cartridge in the printer C. Change the feed rate of the paper D. Clean the printer's transfer roller

B. Replace the toner cartridge in the printer

Which of the following tools is used to identify why an 802.11g network is intermittently dropping network traffic? A.Cable tester B.WiFi analyzer C.Tone generator and probe D.Multimeter

B. WiFi analyzer A WiFi analyzer can determine the wireless network's signal strength, the frequencies in use, and any possible radio frequency interference. Based on the issue described in the question, the network may have dead zones that could be fixed by adding additional access points to increase the network's wireless coverage.

Rick, a computer technician, was contacted by a customer who wants to reduce his office computer's footprint to save space. Which of the following cases is the smallest form factor? A.ATX B.mITX C.mATX D.ITX

B. mITX since the customer wants to save space and reduce the computer's overall size, Rick should use an mITX (Mini-ITX). The mITX contains a smaller footprint than the other options presented and measures only 6.7" x 6.7" in size.

Which of the following ports is used for the request and distribution of DHCP configuration information? A.162 B.67 C.80 D.53

B.67 The dynamic host control protocol (DHCP) is a protocol used to allocate IP addresses to a host when it joins a network. DHCP utilizes UDP ports 67 and 68.

What type of cable should be used to connect a laptop directly to another laptop to form an Ethernet network? A.Patch cable B.Crossover cable C.Straight-through cable D.Serial cable

B.Crossover cable A crossover cable should be used to connect two similar devices (PC to PC, Router to Router, Switch to Switch, etc.) to create a network.

This is a simulated PBQ. If you had this question on the real exam, you would be asked to drag-and-drop a label with the component's name onto the proper location on the port cluster.) Using the image above, which of the following correctly indicates the port labeled as F? A.HDMI B.DVI-D C.DVI-I D.VGA

B.DVI-D

If you are troubleshooting a S.M.A.R.T error on a customer's PC, which of the following devices would you be troubleshooting? A.Memory B.Hard drive C.Processor D.Power supply

B.Hard drive S.M.A.R.T. (Self-Monitoring, Analysis, and Reporting Technology) is a monitoring technology that monitors storage devices like HDD (hard disk drive) and SSD (solid-state drive). This technology is used to provide the proper attribute errors or the drive's current state to warn users and technicians of a pending drive failure.

You are configuring a SOHO network that will contain 7 devices, but you only have a single public IP address. Which of the following concepts should be configured to allow the 7 devices to share that single IP when connecting to the internet? A.DHCP B.NAT C.UPnP D.Perimeter network

B.NAT Network address translation (NAT) is a network service provided by a router or proxy server to map private local addresses to one or more publicly accessible IP addresses.

What is the lowest layer (bottom layer) of a bare-metal virtualization environment? A.Host operating system B.Physical hardware C.Hypervisor D.Guest operating system

B.Physical hardware The bottom layer is physical hardware in this environment. It is what sits beneath the hypervisor and controls access to guest operating systems. The bare-metal approach doesn't have a host operating system. A hypervisor is a program used to run and manage one or more virtual machines on a computer

(This is a simulated PBQ. If you had this question on the real exam, you would be asked to drag-and-drop a label with the component's name onto the proper location on the motherboard.) Using the image of the motherboard above, which of the following correctly indicates the circled area? A.Front connection B.Port cluster C.AGP D.PATA connector

B.Port cluster

A customer contacts the service desk because their laptop will not power on when plugged in, and the battery is dead. The service desk replaces its battery, connects it to a different power adapter, and the laptop works all day until the battery runs out. Now, the laptop won't turn on, and the battery won't charge. Which of the following do you recommend to solve this issue? A.Connect the laptop to a 220v outlet B.Replace the DC jack C.Replace the battery D.Replace the power adapter

B.Replace the DC jack This scenario indicates that the DC jack is faulty. Since the battery was replaced and the laptop continues to work, this indicates it isn't a battery issue but is, instead, most likely a DC jack issue.

A client contacts the service desk because their laptop will not charge when plugged in. The client states that the laptop runs properly while connected to the wall outlet, but if they unplug it, then the laptop immediately powers off. Which of the following do you recommend to solve this issue? A.Replace the DC jack B.Replace the battery C.Replace the power adapter D.Connect the laptop to a 220v outlet

B.Replace the battery

You are at the grocery store. At the checkout, you slide your credit card through the payment terminal and then sign your name to authorize the charge. Which of the following did you MOST likely use to make this purchase? A.Touchpad B.Signature pad C.Bluetooth reader D.NFC device

B.Signature pad

What material is first applied to a CPU during installation to help draw excess heat away from the processor? A.Heat sink B.Thermal paste C.Liquid-cooled radiator D.Cooling fan

B.Thermal paste Thermal paste is a paste used to connect a heat sink to a CPU that provides a liquid thermally conductive compound gel to fill any gaps between the CPU and the heat sink to transfer heat more efficiently to the heat sink from the CPU.

Susan, an executive at Dion Training, will be traveling to Italy for a conference next week. She is worried about remaining connected to the internet while overseas and plans to use the WiFi in her hotel room and the local coffee shop with her laptop. Which of the following should she purchase and configure before leaving for Italy to ensure her communications remain secure regardless of where she is connecting from? A.Local SIM card for her smartphone B.VPN C.International data roaming plan on her cellphone D.Local mobile hotspot

B.VPN

A military contracting firm is worried about proprietary corporate information being removed from the company's network. To combat this, they have created strict rules regarding what types of information can leave their office building. You have been asked to fix a workstation for the company and have been brought on-site to troubleshoot the issue. You have properly followed the troubleshooting steps and have created a plan of action to fix the workstation. Unfortunately, your solution will require that the workstation be taken back to your off-site repair shop to solve the workstation's problems fully. What is the NEXT thing you should do to fix this workstation? A.Format the hard drive of the workstation to delete all proprietary data before taking the workstation to your repair shop B.Verify the contracting firm's corporate polices regarding the removal of a workstation for repairs C.Ask the employee who usually works on the workstation if you can take it to your repair shop D.Remove the internal hard disk drive and then take the workstation with you to your repair shop to fix it

B.Verify the contracting firm's corporate polices regarding the removal of a workstation for repairs

Which of the following is an open-source wireless communication protocol operating in the 2.4 GHz frequency band and is primarily used for home automation? A.NFC B.Zigbee C.Z-Wave D.Bluetooth

B.Zigbee Zigbee is an open-source wireless communication protocol used for home automation. Zigbee is open-source, unlike Z-Wave, which is proprietary. Zigbee uses the 2.4 GHz frequency band.

Match the IPV4 Addresses to the Address Type: APIPA? A. 12.174.25.98 B. 127.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

C. 169.254.1.1

You are setting up a hotel ballroom for a training workshop. Which of the following devices would BEST allow the conference attendees to connect their laptops to the hotel's network when inside the conference areas? A.Router B.Hub C.Access Point D.Switch

C. Access Point A wireless access point (WAP), or access point, connects directly to a wired local area network and the AP then provides wireless connections using Wi-Fi for other devices to use that wired connection. An AP supports the connection of multiple wireless devices through their one wired connection.

You are working for a logistics company that needs to get a device that will automatically enter information about a package when it is read using light and a lens. Which of the following devices should you install to BEST support this requirement? A.Touch screen B.Digitizer C.Barcode reader D.Webcam

C. Barcode reader A barcode scanner or barcode reader is a handheld or pen-shaped device designed to scan barcodes. A barcode is a pattern of different sized parallel bars, typically representing a product number, such as an ISBN, EAN, or UPC. The reader uses a sensor mechanism (typically either a photodiode, laser, or CCD) to read the intensity of light reflected by the barcode.

You have just set up a Minecraft server on a spare computer within your network and want your friends to connect to it over the internet. What do you need to configure in your SOHO router to allow your friends to connect to the new Minecraft server you created? A.Configure your Wi-Fi to use Channel 11 B.Update the firmware C.Configure port forwarding D.Enable DHCP

C. Configure port forwarding Port forwarding occurs when a router takes requests from the Internet for a particular application, such as HTTP/port 80), and sends them to a designated host on the local area network.

Tamera just purchased a Wi-Fi-enabled Nest Thermostat for her home. She has hired you to install it, but she is worried about a hacker breaking into the thermostat since it is an IoT device. Which of the following is the BEST thing to do to mitigate Tamera's security concerns? (Select TWO) A. Enable two-factor authentication on the device's website (if supported by the company) B. Configure the thermostat to use the WEP encryption standard for additional confidentiality C. Configure the thermostat to connect to the wireless network using WPA2 encryption and a long, strong password D. Disable wireless connectivity to the thermostat to ensure a hacker cannot access it E. Configure the thermostat to use a segregated part of the network by installing it into a screened subnet F. Upgrade the firmware of the wireless access point to the latest version to improve the security of the network

C. Configure the thermostat to connect to the wireless network using WPA2 encryption and a long, strong password E. Configure the thermostat to use a segregated part of the network by installing it into a screened subnet

Dion Training is upgrading its wired network from an older CAT5e network to a CAT 7 network. The network technician has run out of patch cables and asks you to create a straight-through patch cable. Which of the following tools is used to connect an RJ-45 connector to a patch cable? A.Punchdown tool B.Cable Tester C.Crimper D.Cable stripper

C. Crimper A crimper is a tool used to attach an RJ-45 plastic connector to an unshielded twisted pair (UTP) or shielded twisted pair (STP) cable

Jason's iPad only had 12% battery remaining at the end of the day, so he connected his iPad to the lightning cable and wall adapter last night before going to bed. In the morning, Jason tried to turn on the iPad, but it appeared to be completely powered down, and the battery was drained. Jason connected the lightning cable to his iPhone, and the iPhone began charging. Which of the following is MOST likely the reason that the iPad didn't charge overnight? A.Defective AC adapter B.Defective battery C.Defective charging port on the iPad D.Defective lightning cable

C. Defective charging port on the iPad

Which of the following parts is responsible for converting the analog signals created by your tapping or swiping the surface of a display to a binary signal that is understood by the underlying software? A.Capacitor B.Backlight C.Digitizer D.Inverter

C. Digitizer The digitizer is a touch-sensitive glass panel covering the LCD in a touchscreen assembly.

Your company has decided to begin moving some of its data into the cloud. Currently, your company's network consists of both on-premise storage and some cloud-based storage. Which of the following types of clouds is your company currently using? A.Private B.Public C.Hybrid D.Community

C. Hybrid

Which of the following laptop displays requires an inverter? A.LED B.OLED C.LCD D.Plasma

C. LCD An inverter supplies the correct AC voltage to the LCD's fluorescent backlight from the laptop's DC power circuits. An LCD (TFT) with fluorescent backlight has been the standard display technology for the last few years. The backlight is a fluorescent bulb that illuminates the image, making it bright and clear.

Which of the following form factors provides a mini card interface used to connect a laptop's SSD at higher bus speeds than SATA? A. 1.8" B. 3.5" C. M.2 D. 2.5"

C. M.2 M.2 s a new set of form factors for mini card interfaces. An M.2 SSD provides a direct interface with the PCI Express bus to provide higher bus speeds than a SATA connection. M.2 adapters come in four different sizes based on their length. The one chosen depends on your model of laptop and the space available within the case. The 80mm variety is the most common one used in modern laptops.

What type of expansion bus technology uses lanes with point-to-point communication paths between two components on the motherboard? A.AGP B.PCI-X C.PCIe D.PCI

C. PCIe PCIe (Peripheral Component Interconnect Express) uses lanes between any two intercommunicating devices. This utilizes a separated pair of wires for both directions of traffic. This increases the bus lanes' speed since there is no possibility of collisions or waiting for other devices to finish communicating.

You want to create a new mobile application and develop it in the cloud. You just signed up for a cloud-based service provider's offering to allow you to develop it using their programming environment. Which of the following best describes which type of service you have just purchased? A.DaaS B.IaaS C.PaaS D.SaaS

C. PaaS Platform as a Service (PaaS) provides the end-user with a development environment without all the hassle of configuring and installing it themselves

Jason's cellphone company allows him to use his smartphone as a wireless hotspot with his laptop when traveling. Jason notices that if he runs a speed test from his smartphone, the cellular connection is 8761 kbps. If he runs the same speed test connection from his laptop connected to his cellphone over its wireless hotspot, the speed drops to 243 kbps. Which of the following is the MOST likely cause for the drop in the speed test results? A.The laptop is out of range of the smartphone's hotspot B.The smartphone's RFID signal is low C.The wireless hotspot feature is throttling the cellular connection speed D.The SSID for the wireless hotspot is not being broadcast

C. The wireless hotspot feature is throttling the cellular connection speed

Which of the following is categorized as a public IP address? A.169.254.12.64 B.172.30.15.12 C.11.120.32.41 D.192.168.0.2

C.11.120.32.41 To communicate on the Internet, a host must obtain a unique public IP address. Typically this is allocated by an Internet Service Provider. If an address is not an APIPA address (169.254.x.x), a private IP address (10.x.x.x, 172.16-31.x.x, or 192.168.x.x), or a localhost IP (127.0.0.1), then it is considered a public IP address.

Which of the following types of connectors are used to terminate a serial cable for an external modem? A.RJ-45 B.RJ-11 C.DB-9 D.LC

C.DB-9 DB-9 connectors are designed to work with the EIA/TIA 232 serial interface standard, which determined the function of all nine pins as a standard so that multiple companies could design them into their products. DB-9 connectors were commonly used for serial peripheral devices like keyboards, mice, joysticks, and data connectivity. Today, the DB9 has mostly been replaced by more modern interfaces such as USB, PS/2, Firewire, etc.

Which of the following components would require you to de-solder the old part from the laptop to install and solder in a new one? A.Battery B.Cellular card C.DC jack D.Screen

C.DC jack It is relatively common for the DC jack to fail over time. The DC jack can become loose over time, or the jack itself can become separated from the motherboard.

A customer recently purchased a touchscreen laptop to use for her schoolwork. It has been working well for about 3 weeks, but today she has brought it into your store for repair because it is not working properly. When she touches an icon on the screen, the program fails to load. You look over the laptop, and the screen appears to be fully intact with no dark blobs or spider web cracks in the panel. You attempt to operate the laptop using the touchscreen, but it appears non-responsive to your touch. You can, however, click on the icons using the laptop's touchpad without any issues. Which of the following components MOST likely needs to be replaced? A.Inverter B.GPU C.Digitizer D.LCD panel

C.Digitizer

Which of the following protocols operates over port 143 by default? A.RDP B.HTTPS C.IMAP D.POP3

C.IMAP The internet message access protocol (IMAP) is a TCP/IP application protocol that provides a means for a client to access email messages stored in a mailbox on a remote server using TCP port number 143.

Which of the following cables is NOT used by Android smartphones and tablets? A.USB-C B.Mini USB C.Lightning D.Micro USB

C.Lightning

Your college has several campuses located across the city. Within each campus, the buildings are interconnected with a campus area network. If you connect each of the campuses across the city, what type of network would this become? A.PAN B.LAN C.MAN D.WAN

C.MAN

Tamera was responding to a complaint that one of the employees is having problems with the wired network connection on their laptop. She investigated the issue to see why it will not connect to the network. Tamera looked at the indicator lights, but she doesn't see the blinking she expected to view. Instead, the light is steady. What is MOST likely the issue? A.Intermittent connectivity B.Low RF signal C.No network activity D.Incorrect TCP/IP configuration

C.No network activity If the lights are steady on a network interface card (NIC), it indicates that there is no network activity. If it is blinking, this indicates that data is passing over the NIC to the network.

A computer technician is configuring a NAS for a company to store their corporate data. The technician has only two hard drives available for use and needs to ensure that the data's fault tolerance and redundancy. Which of the following would be is the best configuration to implement? A.RAID 0 B.RAID 5 C.RAID 1 D.RAID 10

C.RAID 1 While either a RAID 0 or RAID 1 can be used with only two drives, only a RAID 1 will provide redundancy and fault tolerance.

Which of the following technologies is commonly used to inventory the organization's equipment by attaching a tag to the device containing a chip programmed with the assets data, allowing one-way communication to occur from the tag to the reader? A.Z-Wave B.NFC C.RFID D.Zigbee

C.RFID An RFID tag contains an RFID chip programmed with the asset data. This is read wirelessly by an RFID (radio frequency identification) reader. RFID is a one-way communication mechanism, whereas NFC is two-way communication.

While performing routine maintenance on your company's firewall, you discover that port 3389 is open. Which service uses this port? A. Secure Hypertext Transfer Protocol B. File Transfer Protocol C. Remote Assistance D. Hypertext Transfer Protocol

C.Remote Assistance, Port 3389 is used by the Remote Desktop Protocol (RDP) in Windows. If the port is closed on your firewall, you will not be able to give remote assistance to remote users.

What is the MOST common connector type used when connecting a USB cable to the back of a printer? A.Micro-USB B.Type A C.Type B D.Mini-USB

C.Type B This connector has a large square-shaped male connector that is connected to the rear of the printer.

Match the IPV4 Addresses to the Address Type: CLASS B? A. 12.174.25.98 B. 12.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

D. 162.58.123.84

During a disaster recovery, which of the following statements is true? A.A virtual machine cannot be used for redundancy or load balancing B.Both a virtual machine and a physical server has the same downtime C.A virtual machine has more downtime than a physical server D.A virtual machine has less downtime than a physical server

D. A virtual machine has less downtime than a physical server

(This is a simulated PBQ. If you had this question on the real exam, you would be asked to drag-and-drop a label with the component's name onto the proper location on the motherboard.) Using the image of the motherboard above, which of the following correctly indicates the circled area? A.Reset jumper B.Mini PCIe C.Memory slot D. CMOS battery

D. CMOS battery The area circled indicates the CMOS battery on this motherboard. The CMOS battery is used to keep power to the BIOS configurations, such as the date and time, when the power is removed from a desktop or workstation.

You are installing a new projector in a customer's home theater room. After connecting the projector and powering it on, you notice some odd debris displayed on the screen. Which of the following should you do to correct this? A.Degauss the projector B.Adjust incorrect color pattern C.Replace the bulb with correct lumens D.Clean artifacts on the protective glass

D. Clean artifacts on the protective glass

Your boss wants to be able to remotely print from her laptop and smartphone while away from the office. She asks you to set up a method to ensure that she doesn't have to go back to her office to print a document. Which of the following should be configured to meet this requirement? A.WiFi printing B.Integrated print server C.Bluetooth printing D.Cloud printing

D. Cloud printing

What is the simplest and most cost-efficient way to allow other network users to access a printer if the printer does not have an RJ-45 or WiFi adapter available? A.Order another printer with network capabilities and share it on the network B.Establish a printer share on the network switch C.Order a printer port converter to share a non-networked printer D.Establish a print share on the local host

D. Establish a print share on the local host The simplest and most cost-efficient way to share a printer is to share the printer via the local host and allow sharing across everyone to access the printer. While this costs nothing to establish and requires no additional hardware, it does require that the local host remains on 24 hours a day so that others can print to it at any time.

A client has a workstation with a RAID 5 configuration and reports that slower than normal performance occurs when reading/writing files to the RAID. You run a diagnostic program against the RAID, and the system passes all of the diagnostic tests without any issues. While you are running the tests, though, you heard clicking noises coming from the RAID. Which of the following is the MOST likely cause of the slow performance being experienced by the client? A.RAID controller B.SSD C.Cooling fan D.Hard drive

D. Hard drive Based on the symptoms described, the RAID itself is fully functional, so the RAID controller is not causing any problems. This could be caused by a failing hard drive or the system overheating due to the slow performance. Since there is a clicking noise, this is most likely a hard drive failure since a cooling fan makes a whirring or grinding noise instead. Therefore, we can assume the RAID is made up of magnetic hard drives, and one of those hard disks is starting to fail

You and your friends are hanging out in a bar downtown and notice that the entire area around the bar has a great wireless network called "Downtown Metro." This wireless network was built by the city and currently covers about 5 square blocks of the downtown area. What type of network best classifies this wireless network? A.WAN B.LAN C.PAN D.MAN

D. MAN

You have been asked to set up the email on a corporate laptop. The employees of Dion Training are only allowed to receive their email on one device. The email should be removed from the server's mailbox whenever the client connects to the server to download the messages. Which of the following mail protocols should you configure to allow an employee to receive their mail on their laptop and meet these requirements? A.IMAP B.SMTP C.HTTPS D.POP3

D. POP3 The post office protocol (POP3) is a TCP/IP application protocol providing a means for a client to access email messages stored in a mailbox on a remote server over port 110.

You are troubleshooting a workstation for a customer. The workstation will not boot. When it is powered on, an error message of "OS not found" is displayed on the screen. What is the MOST likely solution to fix this error? A.Perform a chkdsk B.Repartition the hard disk C.Replace the HDD with an SSD D.Repair the MBR

D. Repair the MBR The "OS not found" error at boot time is an indication that the MBR (Master Boot Record) or GPT (Globally Unique ID Partition Table) is corrupted or faulty. If this occurs, you should reboot into the Windows recovery mode and use the 'bootrec /fixmbr' command to fix the MBR.

You are troubleshooting a problem with Windows computer. When you boot up the computer, you hear the hard disks start, the computer beeps once, and everything appears normal except the display. The display is blank. You confirm that the monitor is plugged in. What should you do next to troubleshoot this problem? A. Replace the power supply B. Replace the video card C. Install new video display drivers D. Replace the monitor

D. Replace the monitor

Which button on a desktop computer begins a reboot of the computer without power being removed from the computer's components? A.Power B.Suspend C.Hibernate D.Reset

D. Reset

A customer's Android smartphone is only 6 months old but is becoming excessively slow. When questioned, the customer states it was acting fine until they recently installed a new stock market tracking app. What action should you take to troubleshoot the slow performance on this phone? A.Perform a hard reboot of the smartphone B.Replace the phone with a newer model C.Factory reset the smartphone and reinstall all the apps D.Uninstall the app, reboot the phone, and reinstall the app

D. Uninstall the app, reboot the phone, and reinstall the app

You have determined that several computers on your company's network need to have the BIOS updated. Which of the following changes to your computer would MOST likely require that you flash a computer's BIOS afterward? A. Changing the boot sequence B. Adding memory C. Replacing the system board D. Upgrading CPU

D. Upgrading CPU

Dion Training just installed a new webserver within a screened subnet. You have been asked to open up the port for secure web browsing on the firewall. Which port should you set as open to allow users to access this new server? A.143 B.80 C.21 D.443

D.443 The hypertext transfer protocol secure (HTTPS) is a secure protocol used to provide web content to browsers using SSL/TLS encryption over port 443. The hypertext transfer protocol (HTTP) is a protocol used to provide web content to browsers using port 80. The hypertext transfer protocol (HTTP) is a protocol used to provide web content to browsers using port 80. The file transfer protocol (FTP) is the protocol used to transfer files across the internet over ports 20 and 21.

You work for the city's Department of Motor Vehicles (DMV). There are five DMV locations spread out across the city that you have been asked to connect with a network. You have created a list of requirements for this network, including that it must be wired and support at least 1 Gbps of bandwidth. Which of the following network types would MOST likely be used for the DMV to connect their internal networks across the city securely? A.WAN B.PAN C.LAN D.MAN

D.MAN A metropolitan area network (MAN) is a computer network that interconnects users with computer resources in a geographic region of the size of a metropolitan or city area.

Dion Security Group has established a Security Operations Center (SOC) that operates 24/7. They have several 65" plasma TVs at the front of the room that are used as computer displays to show open tickets. You turned off the televisions to clean the screens and noticed that the company logo is still visible in each of the screens' upper left corners. Which of the following should you do to correct this? A.Degauss the television B.Replace the video card C.Replace the HDMI cable D.Replace the plasma TVs

D.Replace the plasma TVs The logo in the upper left corner has been burned into the display since it is a static image. This is common with plasma displays and TVs. To fix this, you need to replace the TVs.

You are configuring a workstation to be used as a point of sale (POS) device. Which of the following peripherals should you install with the device? A.Webcam B.Flatbed scanner C.Memory card reader D.Signature pad

D.Signature pad

Which of the following cables supports both charging and data transfer with a non-directional connector inserted into a port on the device? A.USB-A B.Micro-USB C.Mini-USB D.USB-C

D.USB-C USB-C can be inserted in any direction since it is designed as a non-directional connector.

Match the IPV4 Addresses to the Address Type: Multicast? A. 12.174.25.98 B. 127.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

E. 225.47.72.63

Match the IPV4 Addresses to the Address Type: CLASS C? A. 12.174.25.98 B. 127.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

F. 219.214.211.167

Match the IPV4 Addresses to the Address Type: Private? A. 12.174.25.98 B. 127.0.0.1 C. 169.254.1.1 D. 162.58.123.84 E. 225.47.72.63 F. 219.214.211.167 G. 172.16.2.3

G. 172.16.2.3


Related study sets

Life Insurance Exam Question (Texas)

View Set

List of High Schools in New York

View Set

Excel Ch. 3 Creating and Editing Charts

View Set

Assessment and Airway management

View Set

Professional Communications Chapter 1 and 2

View Set

Chapter 3: Categorical Grants and block grants

View Set

section 5 unit 4 types of encumbrances

View Set

staffing multiple choice questions

View Set