Final Metallurgy Test T/FWrought
Iron undergoes four phase changes when cooled from the melting point to the ambient temperature
F
Isotropu is the devlopment of direction specific properties due to cold working
F
Low beryllium coppers have relatively low electrical conductivity
F
Many ASTM standards contain supplementary requirements that are incorporated at the beginning of a standard and are identified by the letter R
F
Martensitic stainless steels contain the greatest amount of chromium and are the most corrosion resistant
F
Mss Sp 55 is a standard developed by the ALuminum Association
F
Prior cold working is required to initiate grain growth
F
Resolved shear is the combination of slip planes and directions in the crystal lattice in which plastic deformation by slip occurs most favorably
F
Silicon is a strengthening agent in precipitation hardened alloys
F
Stainless steels have a higher resistance to highly reducing acids
F
Stress relieving of austenitic stainless steels must be performed at lower temperatures than for most steels
F
The 2xxx series alloys are more corrosion resistant than most other aluminum alloys
F
The 5xxx series alloys have low strength and poor weldability
F
The 7xx.x series alloys are machinable, weldable, and exhibit excellent castability
F
The 8xxx series comprises aluminum magnesium alloys
F
The amount of carbon that is dissolved in iron has no effect on the phase changes that occur
F
The corrosion resistance of austenitic precipitation hardening stainless steels is greater than that of the regular austenitic stainless steels.
F
The duplex stainless teel has a two phase microstructure consisting of ferrite and pearlite
F
The final staged of reduction in hot working operations must be conducted well above the recrystallization temperatures
F
The longer the holding time at a particular stress relieving temperature, the less the precent of residual stress removed
F
The most common hardening heat treatments for copper alloys consist of precipitation hardening, transformation hardening, spinodal decomposition, and stress relieving
F
The principle reason for using carbide formers is that they combine preferentially with iron
F
The relatively high chromium content of ferritic stainless steels places them to the left of the gamma loop
F
The three stages of steelmaking are oxidation, deoxidation, and rimming
F
The three variations of big end down ingot mold are open top, bottle top, and plug bottom.
F
Tough Pitch copper is the easiest copper alloy to spin
F
When a crystal containing an edge dislocation is mechanically loaded, the dislocation moves 1 Burgers bectors
F
Wrought Iron contains large amounts of carbon and manganese
F
Wrought stainless steels are AISI designated by five numbers followed by a letter
F
Wrought tin bronzes contain signifigantly more lead than their cast equivalents
F
Yellow brasses are cheaper by weaker than red and semi red brasses
F
Fiber Structure is the elongation of inclusions and impurities in the direction of cold work
T
For complete transformation to austenite, a steel must be heated above its AC3 or ACcm temperature
T
Foundries that cast copper alloys use prealloyed ingot, scrap, and virgin metal for raw materials
T
Hot working permits more deformation than cold working
T
Hypoeutectoid steel with 0.2% C has good weldability and formability.
T
In coarse grain steel, the grain size increases as the temperature is increased above the A1.
T
Low operation temperatures decrease pitting and crevice corrosion
T
Nickel is added to aluminum bronzes to improve corrosion resistance
T
Normalizing decreases the pearlite interlamellar spacing and refines grain size.
T
Precipitation hardened aluminum alloys are less easy to weld than other aluminum alloys
T
Precipitation hardening stainless steels can be heat treated to higher strengths than any other stainless steels
T
Re crystallization leads to a sharp drop in strength and a rise in ductility
T
Recovery occurs without any apparent change in the mechanical or physical properties except for electrical conductivity
T
Red and semi red brasses are the easiest alloys to cast
T
Reduction is the removal of chemically combined oxygen in iron ore
T
Semi austenitic precipiation hardening stainless steels are chiefly available in sheet form
T
Silicon bronzes have high strength, good toughness, and excellent corrosion resistance
T
Slip is a process of plastic deformation in which one part of a metal grain undergoes a shear displacement relative to another
T
Stainless steels are the most widely used of all corrosion resistant alloys
T
Stainless steels are usually cut by shearing or blanking
T
Stainless steels generally fail because of localized forms of corrosion
T
The 3xx.x series alloys are the most important because of their superior casting characteristics
T
The 8xx.x series comprises aluminum alloys with approximately 8% Sn
T
The checker chamber of an open hearth furnace preheats the air and helps to improve the efficiency of the furnace
T
The corrosion resistance of aluminum alloys is strongly influenced by the alloy content
T
The larger the austenite grain size, the coarser the ferrite pearlite grain size
T
The most favorable orientation of a crystallographic plane for slip is 45 degrres to the direction of applied force
T
The principle alloying elements in aluminum are copper, magnesium, silicon, manganese, zinc, and tin
T
The strength of commerically pure aluminum may be more than doubled by cold working
T
The three groups of martensitic stainless steels are low carbon, nickel bearing low carbon, and high carbon.
T
UNS designations consist of an uppercase letter followed by five numbers
T
Unlike other noble metals, copper can be attacked in some environments
T
A pipe is an internal fissure caused by internal tensile stresses resulting from heating and cooling
F
Adding nickel to steel is the most cost effective approach to ensuring a completely austenitic structure
F
Aluminum bronzes are leaded
F
Anneal resistant coppers are modified coppers containing zirconium or nickel and phosphorus
F
Austenitic stainless steels can only be strengthed by heat treatment
F
Casting Processes used for aluminum and aluminum alloys are limited to die casting and sand casting
F
Close packed haxagonal metals have a total of 12 slip systems
F
Coarse grain size increases ductility and toughness
F
Cold working is used on copper alloys that remain ductile above their recrystallization temperatures
F
Copper nickels have excellent strength but lower corrosion resistance than other copper alloys
F
Ferrite is capable of dissolving more carbon than austenite
F
Flaking is the development of internal cracks or bursts usually during cooling after rolling or forging
F
Graphitization renders steel highly ductile
F
Integrated steelworks are smaller operations that produce a limited range of carbon steel finished forms
F
AISI STell Products Manuals indicate restrictions and tolerances applicable to various product forms based on accepted manufacturing practices
T
Aluminum is extracted from bauxite ore
T
An advantage of fully killed steel is the resistance to grain coarsening during high temperature heat treatment operations.
T
Anneal resistant coppers have high resistance to elevated temperatures
T
Annealing is performed on both heat treatable and non heat treatable aluminum alloys
T
Annealing twins are not present in annealed castings
T
Because of grain refinement during multiple pass welding of steel, the weld is stronger than that of single pass welding.
T
Brazing is performed on metals that have very thing cross sections or inaccessible joints
T
Carbon and manganese are the pinciple alloying elements in carbon steel
T
Cast aluminum bronzes have superior galling and fatigue resistance compared to the manganese bronzes
T
Cast beryllium coppers must be solution treated to homogenize their microstructures
T
Coarse grain steel is generally deoxidized with silicon
T
Cold forming is performed on non heat treatable alloys
T
Coper alloys are extensively used for saltwater application
T
Copper alloy castings have wider permissible chemical composition ranges than equivalent wrought copper alloys have
T
Copper is used for its high electrical conductivity and high thermal conductivity more than any other metal
T
Critical temperatures are the same with cooling and heat
T
Crystal roation is the reorientation of individual crystals that are under an applied force, so that the crystallographic planes move into the most favorable orientation for slip
T
Dislocations are usually a combination of edge and screw types
T
Duplex stainless steels have better strength than austenitic stainless steels
T
Equivalent cast and wrought copper alloys have similar machinability
T
Eutectic steel at room temperature consists of 100 percent austenite
T
Ferrite is not present at room temperature for the 18% Carbon. 8% Nickel Alloy
T
Ferritic stainless steels are relatively weak and cannot be hardened by quenching
T
ASTM abd ANSI jointly devloped the unified numbering system for metals and alloys
f
Chinese standards for products are identified by the letters CH
f
Euronorms are identified by the letters UN followed by a number
f
The ASME boiler and pressure vessel code is published in a single document
f
UNS designations consist of a capital letter follow by four numbers
f
Most standards that address welding procedures are developed by the AWS
t
The 5xx.x series alloys are limited by poor castability and weldability
t
The castability of the 2xx.x series alloys is poor
t
The three classes of standards are specifications, test methods, and recommended practices
t
a materials procurement specification should reference applicable ASTM standards
t
