Networking Chapter 3

Ace your homework & exams now with Quizwiz!

___________ refers to the spreading of the signal that different parts of the signal arrive at different times at the destination. a. turnaround time b. propagation delay c. dispersion d. insulation e. attenuation

dispersion

The type of media usually installed on homes and businesses by the telephone company is called ____________. a. fiber optic cable b. coaxial cable c. twisted pair d. phone cable e. phone wire

twisted pair

The type of multiplexer that divides the circuit horizontally into different light frequencies that are transmitted simultaneously across many channels is a: a. wavelength division multiplexer b. time division multiplexer c. statistical time division multiplexer d. frequency division multiplexer e. statistical frequency division multiplexer

wavelength division multiplexer

When converting analog voice data to digital signals, Pulse Code Modulation typically samples the incoming voice signal _______ times per second. a. 8,000 b. 8 c. 18,000 d. 64 e. 256

8,000

If the highest frequency of a circuit is 10KHZ and the lowest frequency is 900 Hz, the bandwidth available for this circuit is : a. 890 Hz b. 8900 HZ c. 9100 Hz d. 9Khz e. 890 KHz

9100 Hz

_________ is the basic physical layout of the circuit. a. point-to-point configuration b. configuration c. circuit configuration d. circuit design e. circuit plan

circuit configuration

Equipment used to transform analog voice signals to digital signals and digital signals to analog signals. a. voice converter b. modem c. codec d. multiplexer e. demodulator

codec

Transmission speeds: a. are the same among all media b. are not a factor in selecting a media because all media have more than enough speed to serve current communication demands c. are a constant, 56Kbps, for all media types d. differ widely among media e. always have a direct correlation with security

differ widely among media

In general, networks designed to transmit primarily computer data are likely to be ________. a. international b. level 1 c. numeric d. analog e. digital

digital

Two fundamentally different types of data are: a. DSL and ADSL b. asymmetric and symmetric c. Microsoft and IBM d. digital and analog e. local area and wide area

digital and analog

The representation of the character A by the group of 8 bits, 01000001, is an example of: a. digital coding b. phase modulation c. binary modulation d. analog transmission e. pitch variation

digital coding

Which of the following media can best withstand harsh environmental conditions? a. shielded twisted pair b. unshielded twisted pair c. Cat 5 twisted pair d. coaxial cable e. fiber optic cable

fiber optic cable

Which of the following media has the lowest error rates and the highest transmission speeds? a. Coaxial cable b. unshielded twisted pair c. shielded twisted pair d. fiber optic cable e. infrared

fiber optic cable

Having a conversation with someone using a cellular phone is an example of _________ transmission. a. simplex b. full-duplex c. half-duplex d. analog e. digital

full-duplex

The two basic types of media are: a. statistical and frequency b. guided and wireless (radiated) c. local and wide area d. attenuator and Gaussian e. duplexed and non-duplexed

guided and wireless (radiated)

The ability to transmit in both directions, but only in one direction at a time is an example of _______________ transmission. a. simplex b. full-duplex c. half-duplex d. analog e. digital

half-duplex

____________ refers to the transmission characteristics of the circuit. a. handshaking b. virtual circuit c. bonding d. logical circuit e. physical circuit

logical circuit

Which of the following would be considered a type of wireless media? a. unshielded twisted pair b. shielded twisted pair c. coaxial cable d. microwave e. fiber optics

microwave

__________ is a line-of-sight type of wireless media. a. coaxial cable b. microwave c. radio d. twisted pair e. fiber optic

microwave

____________ refers to changing the shape of the sound wave in different ways to represent a 1 or a 0. a. digitizing. b. sampling c. modulation d. demodulation e. shaping

modulation

The acronym, Modem, stands for _________________. a. multiplexing/demultiplexing b. more/demote c. Mode-M technique d. modulator/demodulator e. Mod emulation technique

modulator/demodulator

A(n) ___________ divides one high-speed communication circuit into several lower speed circuits for the primary reason of saving communication line costs. a. transponder b. multiplexer c. inverse multiplexer d. codec e. intelligent terminal

multiplexer

In which type of modulation is a 1 distinguished from a 0 by shifting the direction in which the wave begins? a. bandwidth modulation b. amplitude modulation c. frequency modulation d. phase modulation e. codec modulation

phase modulation

Data is physically transmitted from one computer or terminal to another in the ________ layer. a. physical b. transport c. application d. terminal e. data link

physical

Which is not true about point-to-point circuits? a. point-to-point circuits are dedicated to the use of the two computers. b. point-to-point circuits are more expensive than multipoint circuits. c. point-to-point circuits are called dedicated circuits. d. point-to-point circuits reduce the amount of cable required and use the circuit more efficiently than multipoint circuits. e. point-to-point circuits are used when the computers generate enough traffic to fill the capacity of the communication circuit.

point-to-point circuits reduce the amount of cable required and use the circuit more efficiently than multipoint circuits.

Which of the following is not an important factor to consider when selecting media to be used in a network? a. prestige value of the type of media b. type of network c. cost d. transmission distance e. security

prestige value of the type of media

____________ is a modulation technique that combines two different amplitude combinations with eight different phase combinations modulation to send four bits per symbol. a. quadrature amplitude modulation b. time division multiplexing c. synchronous digital line control d. pulse code modulation e. baseband signaling

quadrature amplitude modulation

A(n) __________ circuit is another name for a multipoint configuration. a. analog b. dedicated c. point-to-point d. shared e. simplex

shared

If each sample uses 16 bits and the number of samples taken each second is 8000; then the transmission speed on the circuit is? a. 128 Kbps b. 64 Kbps c. 12800 bps d. 96 Kbps e. 32000 bps

128 Kbps

When sending four bits at a time using frequency modulation, the number of different frequency levels that would be needed would be _______. a. 24 b. 16 c. 2 d. 8 e. 4

16

The typical range of human hearing is: a. 0 to 4,000 Hz b. 0 to 1,200 Hz c. 20 to 14,000 Hz d. 0 to 300 Hz e. 0 to 56,000 Hz

20 to 14,000 Hz

How many bits are required to sample an incoming signal 4000 times per second using 64 different amplitude levels? a. 64 b. 32 c. 16 d. 8 e. 6

6

Time (non-statistical) division multiplexing differs from frequency division multiplexing because it: a. does not share a communication circuit b. splits the communication circuit vertically (with time slots) instead of horizontally c. increases the wavelength and phase angles of the baseband frequency used for transmission d. moves the baseband of a circuit by shifting it to a higher frequency e. reduces baseband signal velocity more than frequency division multiplexing

splits the communication circuit vertically (with time slots) instead of horizontally

With respect to converting digital data into analog signals, AM stands for: a. Asynchronous Manchester b. Analog Multimode c. Amplitude Modulation d. Anomaly Multiplexing e. Analytical Mosaic

Amplitude Modulation

_____________ can be thought of as dividing the circuit horizontally. a. Frequency division multiplexing b. Statistical frequency division multiplexing c. Statistical time division multiplexing d. Time division multiplexing e. Wavelength division multiplexing

Frequency division multiplexing

Which of the following is not a key advantage of digital transmission? a. It permits only low transmission rates. b. It is more efficient. c. It is simpler to integrate voice, video, and data on the same circuit. d. It is more secure. e. It produces fewer errors.

It permits only low transmission rates.

The earliest type of fiber optic systems were: a. Graded index multimode b. Attenuated c. Multimode d. Single mode e. Step mode

Multimode

______ is a modem standard that uses Lempel-Ziv encoding to compress data. a. V.22 b. V.44 c. V.32bis d. V.34 e. RS 232

V.44

Another term for the weakening of a signal over distance is: a. turnaround time b. propagation delay c. dispersion d. insulation e. attenuation

attenuation

The _____________ of a circuit determines a circuit's capacity. a. frequency b. bandwidth c. phase d. amplitude e. loudness

bandwidth

A coding scheme that uses 10 bits to represent each character is capable of representing _________ different characters. a. 256 b. 20 c. 200 d. 512 e. 1024

1024

____________ is one of the most commonly used coding schemes used in data transmission. a. ASCII b. ISDN c. MAU d. ATM e. FDM

ASCII

A _________ is an FDM device that splits the physical circuit into three logical circuits (phone, upstream data, downstream data). a. DSL modem b. cable modem c. wireless router d. V.44 modem e. Serial modem

DSL modem

___________ is not a type of digital signaling technique. a. Non-return-to-zero signaling b. Unipolar signaling c. Manchester encoding d. Return-to-zero signaling e. Data rate signaling

Data rate signaling

______________ refers to the time it takes for a signal to travel from sender to recipient (highly exaggerated with satellite transmission). a. Line-of-sight effect b. Multimode index c. Saturation effect d. Raindrop attenuation e. Propagation delay

Propagation delay

With which type of digital signaling does the signal always return to zero volts after each bit? a. Non-return-to-zero signaling b. Unipolar signaling c. Return-to-zero signaling d. Data rate signaling e. Huffman encoding signal

Return-to-zero signaling

Which of the following statements is correct? a. Parallel transmission is most often used for sending data on a circuit that is made up of one wire. b. Parallel transmission is distinguished from serial transmission by the fact that the transmitting device sends a single bit, then a second bit, and so on, until all the bits are transmitted. c. Parallel transmission is only used for analog data. d. Serial transmission is slower than parallel transmission. e. Parallel transmission is the same as serial transmission.

Serial transmission is slower than parallel transmission.

____________ is used by IM and other applications that provide voice services over lower-speed digital circuits. a. pulse code modulation b. adaptive differential pulse code modulation c. Voice conversation d. code modulation e. phase modulation

adaptive differential pulse code modulation

Microwave transmission: a. is a type of high frequency radio communication b. requires a clear line-of-sight path c. is typically used for long distance data transmission d. does not require the laying of any cable e. all of the above

all of the above

The height of a sound wave is called its: a. frequency b. phase c. amplitude d. bandwidth e. furlong

amplitude

In general, older networks and local loops designed to transmit voice data are likely to be ________. a. international b. level 2 c. numeric d. digital e. analog

analog

Which of the following statements is true? a. the longer the distance of a telephone wire between sender and recipient, the lower the bandwidth across that wire b. the shorter the distance of a telephone wire between sender and recipient, the lower the bandwidth across that wire c. bandwidth is constant across any wire, therefore distance is not relevant to its capacity d. the longer the distance of a telephone wire between sender and recipient, the higher the bandwidth across that wire e. bandwidth is not a term that can be used when discussing telephone transmissions

bandwidth is constant across any wire, therefore distance is not relevant to its capacity

Which type of digital signaling would experience fewer errors because it has more distinct signals? a. unipolar b. serial c. bipolar d. attenuation e. Huffman encoding signal

bipolar

Which of the following is the most secure wired media? a. coaxial cable b. unshielded twisted pair c. shielded twisted pair d. fiber optic cable e. infrared

fiber optic cable

To get more "bandwidth" in a digital transmission, you must: a. increase the range of frequencies available for a transmission b. increase the loudness per transmission c. decrease the bits per second transmission speed d. increase the phase shifts per transmission e. decrease the baud rate per transmission

increase the range of frequencies available for a transmission

Frequency division multiplexing: a. operates by statistically time slicing the signal b. operates by dividing the signal into different frequencies c. uses a codec that divides signals into different channels d. operates by time slicing the signal e. operates by light dividing the signal

operates by dividing the signal into different frequencies

The direction in which the sound wave begins is known as: a. amplitude, which our ears detect as loudness b. frequency, which our ears detect as pitch c. phase d. bandwidth e. furlong

phase

Which of the following is a characteristic of sound waves that can be modulated to convert digital data into analog signals? a. phase b. attenuation c. bipolar d. bandwidth e. codec

phase

_____________ refers to the difference between the original analog data and the approximation of that data using the techniques for translating from analog data to digital signals. a. quantizing error b. handshaking phase c. modulating frequency d. POTS anomaly e. amplitude Trellis effect

quantizing error

When all bits of a character are transferred one after another, the bits are transferred in ___________ mode. a. serial b. frequency division c. multiplexing d. parallel e. full complex

serial

When you send an email from the US to Europe, it likely is transmitted from one continent to another through one of the ______ that connect America and Europe. a. submarine cables b. satellites c. telephone lines d. boats e. modems

submarine cables

_____________ is not a form of modulation used to transform digital data into analog signals. a. synchronous time division b. amplitude shift keying c. amplitude modulation d. frequency modulation e. phase modulation

synchronous time division

The room that contains the cable termination points and the distribution frames is referred to as a. telecommunications closet b. equipment room c. building entrance d. backbone room e. work area

telecommunications closet


Related study sets

Biological Psychology Chapter 5 (Kalat)

View Set

2019nov04 Maternity Newborn Oxcow 2 yrs old

View Set

ch 8 confidence levels and intervals

View Set

Properties and Changes of Matter

View Set

Chapter 39- Assessment of Musculoskeletal Function Prepu

View Set

chp 2 for each cost indicate whether it would be most classified as direct labor, direct materials, manufacturing overhead, selling, or an administrative cost

View Set

Загальна психологія

View Set

healthcare economics | final exam (11-18)

View Set

Chapter 1 APUSH Test Study Guide

View Set