TPC 208 Three-Phase Systems
Specifically, the core, the conductors, the end rings, and the shaft are the main parts of the squirrel-cage motor rotor stator yoke
rotor
Plants where considerable moisture exists often select a 240 V distribution system because it is considered ____________ than a 480 V system. easier to insulate easier to work with more robust safer to use
safer to use
If an induction motor ran at synchronous speed, it would develop zero torque because of the lack of control end play power slip
slip
Wound-rotor motors are used most often in applications that require high starting torque and low starting current, where the driven machine starts frequently infrequently quickly slowly
slowly
A synchronous motor using an amortisseur winding for starting is electrically the same as a ____________ motor. servo-based squirrel-cage induction universal variable-speed dc
squirrel-cage induction
40°C is the maximum temperature at which bearings may be safely operated standard temperature for measuring insulation resistance temperature at which oil oxidizes temperature at which solvent evaporates
standard temperature for measuring insulation resistance
An alternator designed to be driven directly by a low-speed prime mover must have many poles to generate power at 50 or 60 Hz. Alternators directly connected to ____________ often have just two or four poles. diesel engines steam engines steam turbines water turbines
steam turbines
Slipping a pole causes a(n) interruption of current in the ac line reduction of current in the dc line reduction of current in the ac line surge of current in the dc line
surge of current in the dc line
The speed at which the magnetic field of an induction motor rotates is called the frequency power slip speed synchronous speed
synchronous speed
Although alternators can be built with any number of phases, there is little advantage in using more than one two three six
three
High-resistance grounding is used where the continuity of service is vital, even when a ground fault occurs. High-resistance grounding limits the ground current to usually well below 0.1% of the ____________ fault current. four-way single-phase three-phase two-wire
three-phase
A completely automatic auxiliary generator set consists of an automatic ____________ with control relays, automatic engine starting controls, and a generator set with appropriate starting equipment. governor multiconductor transfer switch wattmeter
transfer switch
When considering power factor, remember that the induction motor is electrically equivalent to a ____________ with a short-circuited secondary winding. servo system transformer universal motor wound rotor
transformer
A four-pole, three-phase motor has _____ coils. three four eight twelve
twelve
When removing abrasive dust and particles from the windings of a large motor, a ____________ works better than compressed air. good hand towel spray bottle of kerosene vacuum cleaner wet sponge
vacuum cleaner
When you reconnect the coils of an induction motor designed to run on a potential difference of 240 V so that it will run on 480 V, the insulation is not a concern the potential across each coil is 240 V you reconnect the coils in parallel you reconnect the coils in series
you reconnect the coils in series
In a squirrel-cage induction motor, motor conductor bars inserted in the slots of the rotor core are not insulated from the core because the voltage across each bar is seldom more than ________ V. 0.1 1 10 50
10
A motor rated at 2 hp at full load can develop __________ hp if it delivers its maximum torque. 2 3 to 4.5 4 to 5.5 5 to 6
3 to 4.5
When using compressed air to blow out dust from motor windings, the pressure at the nozzle tip must be less than ________ psi. 20 30 50 90
30
Low-voltage distribution systems are usually classified as ____________ V or less. 240 480 600 4160
600
In most automatic installations, power failure relays act if the potential difference drops to __________ of the rated value. 90% or less 80% or less 70% or less 60% or less
70% or less
In automatic transfer system installations that back up critical electronic gear, action is initiated when the potential difference of any phase drops near ____________%. 50 70 90 99.7
90
In which of the following motors does torque vary inversely with speed? Constant horsepower Constant torque Variable horsepower Variable torque
Constant horsepower
Which of the following is a disadvantage of the Y-delta starter? It produces low starting torque It provides closed transition from starting to running It requires an external transformer It uses a complex motor connection
NOT It requires an external transformer Course 208, Lesson 6; Textbook Reference: 6.55 CBT Reference: Types of Starters
There is no current in the armature of an alternator when the armature is connected to the load field is excited regulator is disconnected rotor is turning
NOT field is excited Course 208, Lesson 8; Textbook Reference: 8.57 CBT Reference: Effect of Current in the Armature
If the load driven by an alternator is purely ____________, the current is in phase with the potential difference. capacitive inductive resistive resonant
NOT inductive Course 208, Lesson 8; Textbook Reference: 8.74 CBT Reference: Load Characteristics and Effects
Jogging, also called ____________, is a series of brief starts that enables a motor to provide small movements of the driven equipment. inching kneeing pausing start-stop
NOT start-stop Course 208, Lesson 7; Textbook Reference: 7.36 CBT Reference: Jogging
When interlocks are used in motor-starting circuits to overcome voltage-drop problems, which motor in the circuit is started first? The largest The smallest The last in the line on the circuit The first in line on the circuit
The largest
When dc power is applied to the rotor of a synchronous motor, a rotating magnetic field is produced a set of north and south poles is produced the motor acts as a squirrel-cage motor torque is produced
a set of north and south poles is produced
Because the rotor of a synchronous motor does not depend on induction to produce current, the ____________ can be larger than in an induction motor. air gap armature brushes rotor
air gap
When taking air-gap measurements on large motors, you should keep a record of the measurements and compare them regularly take measurements, about 90° apart take one measurement in the direction in which the load bears on the bearing all of the above
all of the above
Reduced-voltage starters for three-phase motors change the potential difference across the motor by means of autotransformers or resistors capacitors or autotransformers overload relays or capacitors resistors or overload relays
autotransformers or resistors
A synchronous motor requires only an ac power source only a dc power source both ac and dc power none of the above
both ac and dc power
Single-phase operation of three-phase induction motors on older circuits has caused many motor burnouts circuit-breaker trips fusing dilemmas restarts
burnouts
The supply winding in an alternator can be part of either the rotor or the stator is always part of the rotor is always part of the stator is part of neither the stator nor the rotor
can be part of either the rotor or the stator
Excessive greasing of motor bearings can cause grease to be forced into the windings, as well as ____________ of the grease. churning drying lumping thickening
churning
The two kinds of multispeed induction motors are the multiple-winding motor and the ____________ motor. capacitor-start consequent-pole polyphase six-pole
consequent-pole
In a dual-voltage motor, the potential difference across one phase in a Y-connected winding equals the potential difference across the line divided by 3 divided by the square root of 3 multiplied by 3 multiplied by the square root of 3
divided by the square root of 3
A variable-torque motor produces torque that ____________ and power output that ____________ when the speed doubles. doubles; doubles doubles; quadruples is halved; doubles is halved; remains the same
doubles; quadruples
A motor with a single winding can be connected for four-pole operation only either four-pole or eight-pole operation either six-pole or 12-pole operation four-pole, six-pole, eight-pole, or 12-pole operation
either four-pole or eight-pole operation
The permanent joining of motor frames, conduits, control boxes, and other metal parts not intended to carry current in normal operations is known as equipment bonding equipment grounding short circuiting system grounding
equipment bonding
A relay with inverse-time characteristics operates by induction only faster as the current increases for a specific time after the current reaches a certain value without intentional time delay
faster as the current increases
Induction motors can be connected directly across the line on starting. However, the starting current may be ____________ the rated (running) current. half double four to nine times fifteen times
four to nine times
A synchronous motor is unique in that its speed is controlled by the ____________ of the power supply and is not affected by variations in the ____________ on the motor. frequency; load frequency; torque power factor; load power factor; torque
frequency; load
The frequency of a generator set is controlled by a ____________, which controls engine speed. diac and SCR exciter governor throttle
governor
Certain kinds of steel and brass make excellent long-life slip rings if the metals are burnished lightly coated with Teflon heated slowly highly polished
highly polished
The ____________ motor gets its name from the fact that the rotor is not connected electrically to the source of power. armature induction slipping-pole synchronous
induction
Increasing the load on a motor beyond its rated capacity increases the motor's operating temperature and shortens the life of the fuses insulation overloads terminations
insulation
In a squirrel-cage motor, low starting torque is a result of a high power factor equal resistance and reactance high resistance and low reactance low resistance and high reactance
low resistance and high reactance
Which of the following stops a motor when the potential difference falls too low and automatically restarts the motor when the potential difference returns to normal? low-voltage release low-voltage protection mechanical interlock plugging
low-voltage release
To ensure that three-phase motor control equipment is in good operating condition, you should file the contacts to smooth them lubricate the contacts regularly lubricate the toggle switches regularly maintain a regular plan of inspections
maintain a regular plan of inspections
200°F (95°C) is the maximum temperature at which bearings may be safely operated standard temperature for measuring insulation resistance temperature at which oil oxidizes temperature at which solvent evaporates
maximum temperature at which bearings may be safely operated
On a magnetic across-the-line starter, the incoming power lines are connected to terminals L1, L2, and L3 on the top of the motor starter, and the ____________ leads are connected to terminals T1, T2, and T3 on the bottom of the motor starter. contactor motor overload relay transformer
motor
A lack of torque, a decrease in speed, and growling noises are all indications of a(n) high-resistance point in the rotor circuit open rotor circuit overheated end connection shorted rotor circuit
open rotor circuit
During plugging, the current in an induction motor is higher than the locked-rotor current, causing a(n) increase in power power loss reversal in the rotation of the motor shaft speed up in the rotation of the motor shaft
power loss
In establishing a schedule for inspecting generators, you should match the schedule to the maintenance schedule of the older plant equipment prime mover rest of the maintenance staff voltage regulator
prime mover
An inductor connected in series with the motor winding is found in a(n) autotransformer starter reactor starter resistance starter Y-delta starter
reactor starter
Reduced potential difference in a primary-resistance starter is obtained by connecting ____________ in series with each stator lead, then shunting them out of the circuit at high speed. capacitors overload relays resistors slip rings
resistors
The main difference between low-voltage release and low-voltage protection concerns how the motor is restarted reversed stopped transitioned
restarted