Week 8

Which of the following BEST describes Ethernet flow control? A) A protocol designed to prevent looping in network traffic. B) A configuration that allows traffic from multiple VLANs on a single port. C) A configuration that sends a pause frame to the transmitting device when the receiving device cannot keep up with the volume of data being sent. D) A configuration that allows frames larger than 1,500 bytes to pass through the port without fragmentation.

C) A configuration that sends a pause frame to the transmitting device when the receiving device cannot keep up with the volume of data being sent.

Which of the following is the protocol used for address resolution when you switch from IPv4 to IPv6? A) NDP B) Auto-MDIX C) CSMA/CD D) ARP

A) NDP

You are configuring a switch so that you can manage it using PuTTY from the same network segment. On the switch, you enter the following commands: switch#config terminalswitch(config)#interface vlan 1switch(config-if)#ip address 192.168.1.10 255.255.255.0 Will this configuration work? A) No. The no shutdown command needs to be entered. B) Yes. The switch can now be accessed by PuTTY using the IP address 192.168.1.10. C) No. The switch needs to obtain an IP address from the DHCP server using the ip address dhcp command. D) No. The ip default-gateway command needs to be set.

A) No. The no shutdown command needs to be entered.

Which statements accurately describe the port states of both bridges and switches? (Select two.) A) Ports in a blocked state still receive BPDUs. B) Ports in a blocked state cannot receive BPDUs. C) In the learning state, the MAC address table cannot be populated because the port is blocked. D) In the learning state, the MAC address table can be populated, but frames are not forwarded. E) In the learning state, all ports are in a forwarding state.

A) Ports in a blocked state still receive BPDUs. D) In the learning state, the MAC address table can be populated, but frames are not forwarded.

Which of the following protocols prescribes what to do when a data channel is in use on a half-duplex device? A) ARP B) CSMA/CD C) NDP D) Auto-MDI-X

B) CSMA/CD

What does the ip address dhcp command allow you to do? A) Send the DHCP server address for all connected devices. B) Configure a switch to obtain an IP address from a DHCP server. C) Configure a switch to act as a DHCP server. D) Specify the DHCP relay server for forwarding DHCP packets.

B) Configure a switch to obtain an IP address from a DHCP server.

Which of the following BEST describes port aggregation? A) A priority-based flow control that allows you to prioritize network traffic. B) Multiple ports linked together and used as a single logical port. C) Multiple VLANs traveling through a single port. D) IEEE network standard 802.3.

B) Multiple ports linked together and used as a single logical port.

Your organization's management wants to monitor all the customer services calls. The calls are taken on VoIP phones. Which of the following configurations would BEST help you set up a way to monitor the calls? A) Spanning Tree Protocol B) Port mirroring C) Priority-based flow control D) LACP

B) Port mirroring

Computers A and B are on the same VLAN and are separated by two switches as shown in the exhibit. Computer A sends a frame to Computer B. Which of the following BEST describes the frame's composition as it travels from A to B? A) Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The VLAN ID remains on the frame through the second switch up to Computer B. B) Computer A sends a normal frame. The first switch forwards the frame to the second switch, where the VLAN ID is appended to the frame and forwarded to Computer B. C) Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The second switch removes the VLAN ID before forwarding it to Computer B. D) Computer A appends a VLAN ID to the frame. It travels from switch to switch and arrives at Computer B, where it removes the VLAN ID.

C) Computer A sends a normal frame. The first switch appends a VLAN ID to the frame. The second switch removes the VLAN ID before forwarding it to Computer B.

Which of the following switch features allows you to configure how the switch's MAC address table is filled? A) Spanning Tree Protocol B) Port mirroring C) Port security D) Auto-negotiation

C) Port security

In which type of device is a MAC address table stored? A) Repeater B) Router C) Switch D) Hub

C) Switch

Which command would you use on a switch to enable management from a remote network? A) ip address dhcp B) no shutdown C) ip default-gateway 192.168.10.185 D) ip address 192.168.10.185 255.255.255.0

C) ip default-gateway 192.168.10.185

Which of the following is the open standard for tagging Layer 2 frames? A) NDP B) ARP C) RFC1918 D) 802.1q

D) 802.1q

Which of the following must each device's MTU be set to for jumbo frames to transverse the network without risk of fragmentation? A) 6,000 B) 1,500 C) 3,000 D) 9,000

D) 9,000

You have a large Power over Ethernet flat screen that you are installing in a conference room that requires 70 watts of power. Which of the following IEEE standards does your PoE switch need to provide power for the flat screen? A) PoE++ Type 3 B) PoE C) PoE+ D) PoE++ Type 4

D) PoE++ Type 4

You manage a single subnet with three switches. The switches are connected to provide redundant paths between themselves. Which feature prevents switching loops and ensures that there is only a single active path between any two switches? A) Trunking B) PoE C) 802.1x D) Spanning Tree

D) Spanning Tree

A switch receives a frame with a destination MAC address that is not found in its MAC address table. What happens next? A) The frame is replicated and sent to every active port on the switch. B) The frame is rejected and returned to the source host. C) The frame stops at the switch and is not forwarded until the destination MAC address is manually added to the MAC address table. D) The frame is replicated and sent to every active port on the switch except the source port.

D) The frame is replicated and sent to every active port on the switch except the source port.

You manage a network with two switches. The switches are connected together through their Gigabit Ethernet uplink ports. You define VLAN 1 and VLAN 2 on each switch. A device on the first switch in VLAN 1 needs to communicate with a device on the second switch in VLAN 1. What should you configure to allow communication between these two devices through the switches? A) Spanning Tree B) Bonding C) Layer 3 switching D) Trunking

D) Trunking

You run a small network for your business that has a single router connected to the internet and a single switch. You keep sensitive documents on a computer that you would like to keep isolated from other computers on the network. Other hosts on the network should not be able to communicate with this computer through the switch, but you still need to access the network through the computer. Which of the following should you use in this situation? A) VPN B) Port security C) Spanning Tree D) VLAN

D) VLAN

For which of the following devices does a voice VLAN prioritize traffic? A) Bridge B) Hub C) Layer 3 switch D) VoIP phone

D) VoIP phone