CISCO ICND1 MOCK EXAM Module 5

Which of the following best describes a "router on a stick"? A built-in route process in a Layer 3 switch. A separate physical router that uses multiple physical interfaces to route between VLANs. A router that only uses loopback addresses to route between VLANs. A router that has one physical interface that is logically divided into multiple sub interfaces used to route VLANs.

A router that has one physical interface that is logically divided into multiple sub interfaces used to route VLANs.

You need to connect to your router and intend to use a dial in connection. Which of the following will you use? Console Telnet AUX T1

AUX

A client is connecting to the LAN and using DHCP to obtain an IP address. Which of the following is not a type of packet that is sent from the client? (Choose Two) Discover Acknowledge Request Offer

Acknowledge Offer

You are using the CLI of the router instead of the switch. Which of the following commands could you expect to see that is different than what is available on a switch? Ip address 192.168.1.1 255.255.255.0 Ip address dchp Interface vlan 2 Clock rate

Clock rate

You need to access the CLI on the router in order to configure the IP address on the Ethernet interfaces. What command would you enter next after connecting using SSH, authenticating and typing the command ENABLE? Configure terminal Interface crypto key generate Ip address

Configure terminal

Which of the following is unique to router configuration in comparison with switch configuration? Global configuration Connecting Ethernet cables Connecting serial cables Configuring SSH

Connecting serial cables

Which of the following is defined as the length of time it takes for routers in the same internetwork to update each other's routing tables? Latency Time delay Convergence Round trip

Convergence

A Cisco router configured to use RIPv2 has a packet with a network ID that it does not recognize. Where will it send that packet? Default gateway Default route switch edge router

Default route

If a network router has no knowledge of a destination network, which of the following is chosen for an IP packet? Directly connected Default route Default gateway Static route

Default route

Which of the following commands should you use in order to configure the default gateway for clients leasing addresses from a Cisco router functioning as a DHCP server? ip dhcp router address Ip dhcp pool Dns-server Default-router

Default-router

Which route type has the best possible metric in a routing table? Directly connected RIPv2 Static route EIGRP

Directly connected

You need to access the CLI on the router in order to configure the IP address on the Ethernet interfaces. What command should you enter FIRST from User Exec mode? Configure terminal interface Ip address Enable

Enable

You need to access the CLI on the router in order to configure the IP address on the serial interfaces. What command should you enter FIRST from after logging into the router via SSH? Enable username interface Exit

Enable

OSPF is considered a proprietary protocol designed by Cisco for their own brand of routers True False

False

OSPF is designed to make decisions based on a hop count metric because it is a distance vector protocol. True False

False

Which of the following is the least common connection option on modern routers? AUX Console Serial ISDN

ISDN

What configuration mode is required in order to configure the IP addresses on a Cisco router's S0/1 interface? Global configuration Interface Line vty 0 15 Vlan configuration

Interface

Which configuration mode is required in order to configure the IP addresses on a Cisco router's Fa0/1 interface? Interface Global Configuration Vlan Line configuration

Interface

Which of the following commands configures the DHCP relay feature on a router? Global configuration Ip address dchp Ip helper-address Ip static dhcp

Ip helper-address

What are some key features of split horizon? (Choose two) It is used to suppress RIP counting to infinity. It will not advertise a route back through the same interface it learned the route from. It requires the router to send updates using a multicast address. It only supports VLSM.

It is used to suppress RIP counting to infinity. It will not advertise a route back through the same interface it learned the route from.

You have multiple VLANs on your network. What is now required in order to configure routing between multiple VLANs? (Choose 3) Layer 2 switch Layer 3 switch Router VLAN interface

Layer 3 switch Router VLAN interface

Which of the following is considered to be a link state routing protocol? OSPF EIGRP IGRP RIP

OSPF

Which type of packet is used by the DHCP server to communicate an available IP address to the client? Offer Discover Request Acknowledge

Offer

You need to configure an interface to not advertise routes via RIPv2. Which of the following commands should you use? Passive-interface Active-interface Shutdown No shutdown

Passive-interface

You need to prevent a RouterA interface from learning routes from other routers. Which of the following should you use? Router rip Passive-interface on RouterA Ip address Passive-interface on the other routers

Passive-interface on the other routers

You are troubleshooting router startup processes and need to identify the first process that happens when a Cisco router boots. Which of the following should you choose? Finds and loads the startup-configuration file Performs a POST test Locates the BIOS and MBR Finds and loads the Cisco IOS

Performs a POST test

Which protocol was RIPv2 designed to replace? IGRP EIGRP BGP RIP

RIP

You issue the command show ip route on a router. You see various routes with letters in front of them. What does R stand for? IGRP EIGRP RIP OSPF

RIP

You need to identify the protocols on Cisco routers that support VLSM. Which of the following should you choose? (Choose Two) RIP RIPv2 IGRP EIGRP

RIPv2 EIGRP

Which of the following are considered as a hop when RIPv2 configures the hop count metric for the routing table? Link Router Switch PC

Router

You need to view the IP addresses and subnet masks associated with interfaces on a Cisco router. Which of the following should you choose? Show startup config Show interface Show version Show ip interface brief

Show interface

You need to verify a lease on a Cisco Router DHCP server. Which of the following commands should you use? Show IP address Show ip dhcp server statistics Show ip dhcp pool Show ip dhcp binding

Show ip dhcp binding

Which of the following commands on a Cisco router will identify the interfaces on which RIP is enabled? Show ip route Show ip rip database Show ip protocols Show ip interfaces

Show ip protocols

You are using the CLI of the router instead of the switch. Which of the following commands could you expect to see that is different than what is available on a Layer 2 switch? Show ip interface brief Show interface Show ip route Interface vlan 1

Show ip route

You need to determine which routes were learned through dynamic routing protocols. Which of the following should you use? Show ip route Show interface ip address Show interface status Global configuration

Show ip route

OSPF is considered a vendor neutral protocol that most any router manufacturer can use. True False

True

RIPv2 is considered an industry standard non-proprietary protocol. True False

True

You need to administer a router from a brand new laptop. You want to connect directly. The router is one of the newest models. What will you probably use? Modem USB Ethernet Serial interface

USB

Which of the following is supported using a router configured with RIPv2 in comparison with the original RIP standard? (Choose Two) VLSM Classful addressing Multicast updates Broadcast updates

VLSM Multicast updates

Which command should you use on a router to ensure the router is using the latest version of the RIP dynamic protocol? Router rip Version 1 Version 2 Multicast

Version 2

You need to configure a SOHO wireless router. What is the most likely interface for you to use? Telnet SSH Web page CLI

Web page

What default metrics does EIGRP use to make routing decisions? (Choose two) hop count bandwidth delay link cost

bandwidth delay

You need to create a range of addresses on a Cisco router configured as a DHCP server. Which command should you use? ip dhcp server address Ip dhcp excluded address ip dhcp pool Ip dhcp addresses

ip dhcp pool

You are configuring a static route on Router0 so that PC0 can communicate with PC1. Examine the diagram. Which commands could you use on Router0? (Choose 2) ip route 172.16.1.0 255.255.255.0 172.16.2.1 ip route 172.16.1.0 255.255.255.0 172.16.2.2 ip route 172.16.1.0 255.255.255.0 s0/0/0 ip route 172.16.1.0 255.255.255.0 s0/1/0

ip route 172.16.1.0 255.255.255.0 172.16.2.2 ip route 172.16.1.0 255.255.255.0 s0/0/0

If you have a routing protocol that is automatically summarizing routes into a single route, and you don't want that to happen, what command can you use? autosum no auto summary maximum paths network

no auto summary

You need to connect to the console port on the router from a brand new laptop. Which of the following cables will you most likely use? crossover twisted pair straight through twisted pair rollover serial

rollover

You need to connect the CSU/DSU to the router, which of the following ports will you use? RJ-45 T-1 BNC serial

serial