CISCO ICND1 MOCK EXAM Module 5
Which of the following best describes a "router on a stick"? A built-in route process in a Layer 3 switch. A separate physical router that uses multiple physical interfaces to route between VLANs. A router that only uses loopback addresses to route between VLANs. A router that has one physical interface that is logically divided into multiple sub interfaces used to route VLANs.
A router that has one physical interface that is logically divided into multiple sub interfaces used to route VLANs.
You need to connect to your router and intend to use a dial in connection. Which of the following will you use? Console Telnet AUX T1
AUX
A client is connecting to the LAN and using DHCP to obtain an IP address. Which of the following is not a type of packet that is sent from the client? (Choose Two) Discover Acknowledge Request Offer
Acknowledge Offer
You are using the CLI of the router instead of the switch. Which of the following commands could you expect to see that is different than what is available on a switch? Ip address 192.168.1.1 255.255.255.0 Ip address dchp Interface vlan 2 Clock rate
Clock rate
You need to access the CLI on the router in order to configure the IP address on the Ethernet interfaces. What command would you enter next after connecting using SSH, authenticating and typing the command ENABLE? Configure terminal Interface crypto key generate Ip address
Configure terminal
Which of the following is unique to router configuration in comparison with switch configuration? Global configuration Connecting Ethernet cables Connecting serial cables Configuring SSH
Connecting serial cables
Which of the following is defined as the length of time it takes for routers in the same internetwork to update each other's routing tables? Latency Time delay Convergence Round trip
Convergence
A Cisco router configured to use RIPv2 has a packet with a network ID that it does not recognize. Where will it send that packet? Default gateway Default route switch edge router
Default route
If a network router has no knowledge of a destination network, which of the following is chosen for an IP packet? Directly connected Default route Default gateway Static route
Default route
Which of the following commands should you use in order to configure the default gateway for clients leasing addresses from a Cisco router functioning as a DHCP server? ip dhcp router address Ip dhcp pool Dns-server Default-router
Default-router
Which route type has the best possible metric in a routing table? Directly connected RIPv2 Static route EIGRP
Directly connected
You need to access the CLI on the router in order to configure the IP address on the Ethernet interfaces. What command should you enter FIRST from User Exec mode? Configure terminal interface Ip address Enable
Enable
You need to access the CLI on the router in order to configure the IP address on the serial interfaces. What command should you enter FIRST from after logging into the router via SSH? Enable username interface Exit
Enable
OSPF is considered a proprietary protocol designed by Cisco for their own brand of routers True False
False
OSPF is designed to make decisions based on a hop count metric because it is a distance vector protocol. True False
False
Which of the following is the least common connection option on modern routers? AUX Console Serial ISDN
ISDN
What configuration mode is required in order to configure the IP addresses on a Cisco router's S0/1 interface? Global configuration Interface Line vty 0 15 Vlan configuration
Interface
Which configuration mode is required in order to configure the IP addresses on a Cisco router's Fa0/1 interface? Interface Global Configuration Vlan Line configuration
Interface
Which of the following commands configures the DHCP relay feature on a router? Global configuration Ip address dchp Ip helper-address Ip static dhcp
Ip helper-address
What are some key features of split horizon? (Choose two) It is used to suppress RIP counting to infinity. It will not advertise a route back through the same interface it learned the route from. It requires the router to send updates using a multicast address. It only supports VLSM.
It is used to suppress RIP counting to infinity. It will not advertise a route back through the same interface it learned the route from.
You have multiple VLANs on your network. What is now required in order to configure routing between multiple VLANs? (Choose 3) Layer 2 switch Layer 3 switch Router VLAN interface
Layer 3 switch Router VLAN interface
Which of the following is considered to be a link state routing protocol? OSPF EIGRP IGRP RIP
OSPF
Which type of packet is used by the DHCP server to communicate an available IP address to the client? Offer Discover Request Acknowledge
Offer
You need to configure an interface to not advertise routes via RIPv2. Which of the following commands should you use? Passive-interface Active-interface Shutdown No shutdown
Passive-interface
You need to prevent a RouterA interface from learning routes from other routers. Which of the following should you use? Router rip Passive-interface on RouterA Ip address Passive-interface on the other routers
Passive-interface on the other routers
You are troubleshooting router startup processes and need to identify the first process that happens when a Cisco router boots. Which of the following should you choose? Finds and loads the startup-configuration file Performs a POST test Locates the BIOS and MBR Finds and loads the Cisco IOS
Performs a POST test
Which protocol was RIPv2 designed to replace? IGRP EIGRP BGP RIP
RIP
You issue the command show ip route on a router. You see various routes with letters in front of them. What does R stand for? IGRP EIGRP RIP OSPF
RIP
You need to identify the protocols on Cisco routers that support VLSM. Which of the following should you choose? (Choose Two) RIP RIPv2 IGRP EIGRP
RIPv2 EIGRP
Which of the following are considered as a hop when RIPv2 configures the hop count metric for the routing table? Link Router Switch PC
Router
You need to view the IP addresses and subnet masks associated with interfaces on a Cisco router. Which of the following should you choose? Show startup config Show interface Show version Show ip interface brief
Show interface
You need to verify a lease on a Cisco Router DHCP server. Which of the following commands should you use? Show IP address Show ip dhcp server statistics Show ip dhcp pool Show ip dhcp binding
Show ip dhcp binding
Which of the following commands on a Cisco router will identify the interfaces on which RIP is enabled? Show ip route Show ip rip database Show ip protocols Show ip interfaces
Show ip protocols
You are using the CLI of the router instead of the switch. Which of the following commands could you expect to see that is different than what is available on a Layer 2 switch? Show ip interface brief Show interface Show ip route Interface vlan 1
Show ip route
You need to determine which routes were learned through dynamic routing protocols. Which of the following should you use? Show ip route Show interface ip address Show interface status Global configuration
Show ip route
OSPF is considered a vendor neutral protocol that most any router manufacturer can use. True False
True
RIPv2 is considered an industry standard non-proprietary protocol. True False
True
You need to administer a router from a brand new laptop. You want to connect directly. The router is one of the newest models. What will you probably use? Modem USB Ethernet Serial interface
USB
Which of the following is supported using a router configured with RIPv2 in comparison with the original RIP standard? (Choose Two) VLSM Classful addressing Multicast updates Broadcast updates
VLSM Multicast updates
Which command should you use on a router to ensure the router is using the latest version of the RIP dynamic protocol? Router rip Version 1 Version 2 Multicast
Version 2
You need to configure a SOHO wireless router. What is the most likely interface for you to use? Telnet SSH Web page CLI
Web page
What default metrics does EIGRP use to make routing decisions? (Choose two) hop count bandwidth delay link cost
bandwidth delay
You need to create a range of addresses on a Cisco router configured as a DHCP server. Which command should you use? ip dhcp server address Ip dhcp excluded address ip dhcp pool Ip dhcp addresses
ip dhcp pool
You are configuring a static route on Router0 so that PC0 can communicate with PC1. Examine the diagram. Which commands could you use on Router0? (Choose 2) ip route 172.16.1.0 255.255.255.0 172.16.2.1 ip route 172.16.1.0 255.255.255.0 172.16.2.2 ip route 172.16.1.0 255.255.255.0 s0/0/0 ip route 172.16.1.0 255.255.255.0 s0/1/0
ip route 172.16.1.0 255.255.255.0 172.16.2.2 ip route 172.16.1.0 255.255.255.0 s0/0/0
If you have a routing protocol that is automatically summarizing routes into a single route, and you don't want that to happen, what command can you use? autosum no auto summary maximum paths network
no auto summary
You need to connect to the console port on the router from a brand new laptop. Which of the following cables will you most likely use? crossover twisted pair straight through twisted pair rollover serial
rollover
You need to connect the CSU/DSU to the router, which of the following ports will you use? RJ-45 T-1 BNC serial
serial