IEC Year 2
Which room is located in the NW corner of the building? Select one: a.Bedroom #3 b.Bedroom #2 c.Carport d.Living Room
b. Bedroom #2
The large-scale adoption of the business computer led to a new form of drafting called ___. Select one: a.Building Information Modeling (BIM) b.Computer-Aided Drafting (CAD) c.BlueBeam d.DesignCAD
b. Computer-Aided Drafting (CAD)
Where would you find the kitchen equipment schedule? Select one: a.Division 1 b.Division 11 c.Division 16 d.Division 5
b. Division 11
Which of the following is a graphical representation of a vertical plane of view? Select one: a.Section b.Elevation c.Riser d.Detail
b. Elevation
Continuity (not resistance readings) tests made on components or equipment, with an expected resistance of 2.2 kΩ, will correctly indicate continuity. Select one: a.True b.False
b. False
When testing DC voltage, connect the red test lead to the ___.I. positive polarity test point II. negative polarity test point III. ground Select one: a.I or II only b.I only c.II only d.I or II or III e.I or III only f.II or III only
b. I only
Which type of plan has steel and foundations? Select one: a.Architectural b.Structural c.Power Plan d.RCP
b. Structural
Refer to Figure 201.1M. When inserting the test leads into the meter, the red lead should be inserted in the port panel jack marked ___ for DC voltage measurements. Select one: a.A b.V Ω Hz c.mA d.COM
b. V Ω Hz
CAD is the acronym for ___. Select one: a.computer architecture data b.computer-aided drafting c.costly architecture design d.constant attention to detail
b. computer-aided drafting
Which specification section lists the type and quantity of circuits to be installed? Select one: a.16.1.5 b.16.2.3 c.14.5.7 d.16.3.2
d. 16.3.2
How many inches OC (on center) are the studs to be installed? Select one: a.36″ b.18″ c.24″ d.16″
d. 16″
Which sheet depicts the detail for the East elevation? Select one: a.3 b.4 c.1 d.2
d. 2
The ceiling joists are which board length/width? Select one: a.2″ × 6″ × 18′ b.2″ × 8″ × 18′ c.2″ × 8″ × 24′ d.2″ × 6″ × 24′
d. 2″ × 6″ × 24′
Which sheet shows this section detail? Select one: a.5 b.1 c.6 d.3
d. 3
How many circuits are designated for lighting? Select one: a.2 b.1 c.6 d.4
d. 4
In the reading, how many Divisions directly affect the electrician's scope of work for this residence? Select one: a.2 b.4 c.6 d.7
d. 7
BIM is the acronym for ___. Select one: a.Build-Integrate-Manufacture b.Best in Manufacturing c.Builders Information Modeling d.Building Information Modeling
d. Building Information Modeling
Current is measured in ___. Select one: a.watts b.volts c.amperes d.farads e.ohms
c. amperes
What obstacle(s) are experienced when excavating basements? Select one: a.water table b.bedrock c.both a and b d.none of the above
c. both a and b
Which room do you walk into if you enter the building from the carport? Select one: a.Living Room b.Vestibule c.Bedroom #3 d.Kitchen
d. Kitchen
Which type of plan shows lighting? Select one: a.Architectural b.Structural c.Power Plan d.RCP
d. RCP
The ___ is an isometric view of the distribution system to install from. Select one: a.power plan b.structural plan c.one-line / riser diagram d.general plan
c. one-line / riser diagram
Digital Multimeters are used to measure ___. Select one: a.amperage b.voltage c.current d.resistance e.all of these
e. all of these
When setting the range on a DMM for a voltage measurement, you should set the voltage range ___ the expected voltage. Select one: a.twice as high as b.lower than c.the same as d.80% of e.slightly higher than
e. slightly higher than
Which Type fixture is scheduled to be installed in the bedrooms? Select one: a."A" b."B" c."C" d."D"
a. "A"
What is required for grounding in conduits? Select one: a.#12 copper wire b.#14 copper wire c.#6 bonding wire d.not specified
a. #12 copper wire
How many days are provided for time extensions? Select one: a.0 b.5 c.25 d.16
a. 0
Which sheet number depicts the electrical installation? Select one: a.1 b.2 c.3 d.4
a. 1
What is the scale of detail 3 on A-5.0? Select one: a.1/4″ = 1′ b.1/8″ = 1′ c.1″ = 20′ d.not specified
a. 1/4″ = 1′
The water heater is ___. Select one: a.100 gal. electric b.50 gal. electric c.100 gal. gas d.50 gal. gas
a. 100 gal. electric
In what room is the water heater? Select one: a.108A b.107 c.108 d.110
a. 108A
What room number has the electrical panels? Select one: a.110 b.113 c.108A d.101A
a. 110
What voltage is required for a typical electric oven? Select one: a.120/240V b.120V c.240V d.480V
a. 120/240V
What is the x-ray room number? Select one: a.125 b.128 c.127 d.124
a. 125
What is the timeframe for completion of the Brick Veneer Residence? Select one: a.150 days b.75 days c.150 weeks d.5 weeks
a. 150 days
How many SPST switches for lighting are depicted? Select one: a.19 b.16 c.17 d.12
a. 19
What size conduits are required to the menu board? Select one: a.1″ b.3/4″ c.11/2″ d.2″
a. 1″
How many circuits are to remain as spares? Select one: a.2 b.4 c.6 d.8
a. 2
What size copper wire should be installed for the service? Select one: a.2/0 b.250 kcmil c.4/0 d.1/0
a. 2/0
What power is required to all RTUs? Select one: a.208V, 3ph b.208V, 1ph c.120V, 1ph d.480V, 3ph
a. 208V, 3ph
Which of the following is the spec division for plumbing? Select one: a.22 b.23 c.26 d.27
a. 22
How many different types of lighting fixtures are called out for the site lighting? Select one: a.3 b.2 c.5 d.cannot tell from plan
a. 3
On A-1.2 how many roof top units (mechanical) are shown? Select one: a.3 b.5 c.6 d.7
a. 3
Plywood is composed of which of the following? Select one: a.3 or more plies of wood b.3 or more types of fibers c.3 or more types of gypsum plaster d.3 or more types of particles
a. 3 or more plies of wood
Which division will have specs for brick? Select one: a.4 b.10 c.16 d.2
a. 4
How many receptacles arew to be installed in the Living Room? Select one: a.6 b.8 c.4 d.7
a. 6
On the second floor, LP4 circuit 8 serves how many receptacles? Select one: a.6 b.5 c.7 d.5
a. 6
What size is the sanitary sewer line? Select one: a.6″ b.8″ c.4″ d.10″
a. 6″
From which panel does the micro switch on 15A get power? Select one: a.A b.B c.C d.D
a. A
___ construction creates a bungalow-type structure and is typically limited to residential applications. Select one: a.A-frame b.Balloon c.Platform d.Post and beam
a. A-frame
Safety toe footwear for employees shall meet the requirements and specifications of ___. Select one: a.ANSI b.AAA c.NEMA d.NHRA
a. ANSI
Where is the EWH (Electric Water Heater) located? Select one: a.Basement b.Carport c.Closet d.Bathroom #2
a. Basement
Which drawing type has the grading plan? Select one: a.Civil b.Structural c.Plumbing d.Architectural
a. Civil
Which MasterFormat® Division is used for electrical specifications? Select one: a.Division 26 b.Division 01 c.Division 14 d.Division 44
a. Division 26
Typically, where would we find the finishes that are to be installed in a commercial building? Select one: a.Finish Schedule b.Reflective Ceiling Plan c.Site Plan d.Wall Detail
a. Finish Schedule
Which type of protection is depicted on the drawings for the receptacles in the bathroom? Select one: a. GFCI b.AFCI c.Combination AFCI\GFCI d.No protection shown
a. GFCI
Per the NEC®, receptacles in the residence's crawlspace must have ___. Select one: a.GFCI protection b.surge protection c.AFCI protection d.a weatherproof enclosure
a. GFCI protection
___ are commonly shown on all drawings to provide basic information such as general references, tasks to be performed, or code conformity. Select one: a.General Notes b.Key Notes c.Special Notes d.Information Notes
a. General Notes
The second floor lighting is powered from ___. Select one: a.LP3, LP4, GP2 b.LP3 only c.LP3 and LP4 d.LP4 only
a. LP3, LP4, GP2
Where do you find explanation for the symbols used on drawings? Select one: a.Legend b.Drawing Scale c.Architectural drawings only d.Titleblock
a. Legend
Which drawings have air conditioning? Select one: a.Mechanical b.Electrical c.Fire Alarm d.Fire Protection
a. Mechanical
Who completes the electrical work for heat? Select one: a.Mechanical b.Electrical c.Owner d.Plumbing
a. Mechanical
What type of receptacle is needed for the Frosty machine? Select one: a.NEMA 15-30 b.NEMA 1 c.NEMA 6-20 d.NEMA 5-15
a. NEMA 15-30
The prints provide general requirements and locations for branch power. What other resource should be referred to (in addition to the prints) for electrical installations? Select one: a.National Electrical Code® b.Ugly's™ Electrical Reference c.IEEE d.Canadian Electrical Code®
a. National Electrical Code®
___ persons shall be used to perform any work on live or energized equipment. Select one: a.Qualified b.Quality c.Authorized d.Special
a. Qualified
The fire dampers in the Indoor Yard/Boarding room come from what unit? Select one: a.RTU6 b.RTU1 c.RTU5 d.RTU4
a. RTU6
On the C2 drawing, where in the building is the menu board located? Select one: a.SE corner b.SW corner c.NE corner d.NW corner
a. SE corner
A written Haz Com program requires a list of chemicals known to be present in the workplace, and the methods the employer will use to inform the employees of these hazards. Select one: a.True b.False
a. True
Proper face and eye protection equipment must be selected based on the hazard present or the operation to be performed. Select one: a.True b.False
a. True
Written Haz Com programs shall describe how the labels and other forms of warning, SDS sheets, and employee information and training will be met. Select one: a.True b.False
a. True
Per the specifications, what are we providing with the panelboard upon completion? Select one: a.a detailed panel schedule b.3 free callbacks for tripped breakers c.touch up paint d.nothing, they get what we give them
a. a detailed panel schedule
According to the topographical survey of this project, the existing underground storm piping is to be ___. Select one: a.abandoned b.removed c.filled d.closed-off
a. abandoned
"Faux" finishes on masonry are typically installed with: Select one: a.adhesive b.anchors c.screws d.plaster
a. adhesive
In the reading, arc-fault circuit interrupters (AFCIs) are required in ___ . Select one: a.all rooms of the home b.the kitchen and bathroom c.the bedrooms d.in the carport
a. all rooms of the home
Which of these incidents causes more electrical injuries per year? Select one: a.arc blasts b.electric shock
a. arc blasts
Typically, the ___ draws the equipment, mechanical, electrical, and plumbing plans. Select one: a.architect b.electrician c.mechanical engineer d.general contractor
a. architect
Cold water piping is represented by what kind of line? Select one: a.broken line with one dash b.solid line c.broken line with two dashes d.dotted line
a. broken line with one dash
Which of the following is considered a softwood? Select one: a.cedar b.oak c.maple d.birch
a. cedar
Costs for additional items not covered in the original construction contract are authorized by ___. Select one: a.change orders b.word of mouth c.specifications d.contract appendices
a. change orders
Which type of anchors use pressure to force the anchor in place? Select one: a.compressed gas anchors b.masonry anchors c.cast-in concrete anchors d.concrete anchors
a. compressed gas anchors
Steel pan decking typically is filled with ___. Select one: a.concrete b.brick c.stone d.rock
a. concrete
A requirement of electrical takeoff is providing the appropriate length of cable and ___ of each type and size for the job. Select one: a.conductors b.conduit c.anchors d.fasteners
a. conductors
When working near live parts, you must know the ___ related to the work. Select one: a.dangers b.tools c.workers d.parts
a. dangers
The project delivery method where the owner works with the architect/engineers directly at project start is ___. Select one: a.design-bid/build b.design-build c.time and material d.build-design
a. design-bid/build
Wherever it is not feasible to limit the noise level or duration of exposure to those specified in Permissible Noise Exposures-Table D-2, ___. Select one: a.ear protective devices shall be provided and used b.employees must receive special training and become qualified c.either a or b d.neither a nor b
a. ear protective devices shall be provided and used
Every person working on any ___ system needs to be familiar with the NFPA 70E. Select one: a.electrical b.mechanical c.computer d.solar
a. electrical
The number of home runs is determined by the ___. Select one: a.electrical contractor (EC) b.general contractor (GC) c.architect d.lighting designer
a. electrical contractor (EC)
The purpose of the Haz Com standard is to ensure that the hazards of all chemicals are ___, and that information concerning their hazards is transmitted to employees. Select one: a.evaluated b.marked c.labeled d.identified
a. evaluated
FACP is the acronym for ___. Select one: a.fire alarm control panel b.fixed alarm control panel c.fire actuating control panel d.frequent alarm circuit protection
a. fire alarm control panel
Pages within a set of prints are numbered according to the type and convention. What is an example of a naming convention found within a set of prints? Select one: a.fire protection b.raceways c.framing d.trim
a. fire protection
In all cases where the sound levels are ___ the values shown in Table D-2, a continuing, effective hearing conservation program shall be administered. Select one: a.greater than b.less than
a. greater than
Training must also include the physical and ___ hazards of the chemicals and the measures that employees can take to protect themselves from these hazards. Select one: a.health b.emotional c.stress d.none of these
a. health
Which piping is to be insulated? Select one: a.hot and cold b.hot c.cold d.not specified
a. hot and cold
An employer requires its employees to wear boots with metatarsal protection but does not provide metatarsal guards. A new employee purchases a pair of these boots. The employer ___ required to reimburse the employee for the purchase. Select one: a.is b.is not
a. is
What kind of notes relate to specific items on a drawing? Select one: a.key notes b.spec notes c.footnotes d.general notes
a. key notes
In the reading, the ___ has/have the most code requirements for electrical installations. Select one: a.kitchen b.bedrooms c.living spaces d.hallway
a. kitchen
What is R-Value? Select one: a.measure of thermal resistance b.measure of fire stopping c.measure of length d.measure of weight
a. measure of thermal resistance
Which material is more common today for structural support? Select one: a.metal b.wood c.concrete d.asphalt
a. metal
Where is the existing OH line? Select one: a.north side of the property b.east side of the property c.west side of the property d.south side of the property
a. north side of the property
On the electrical distribution drawing, the power distribution system is labeled "power riser." Other projects may call this a ___. Select one: a.one-line diagram b.ladder diagram c.motor diagram d.multi-line diagram
a. one-line diagram
To measure current in a switched circuit using a DMM, the test leads would be placed on the terminal screws of a(n) ___ switch. Select one: a.open b.closed
a. open
Per the drawings, what type of service are we to install? Select one: a.overhead b.wireless c.underground d.none, the home is off the grid
a. overhead
Which is the most common form of framing? Select one: a.platform b.balloon c.post and beam d.A-frame
a. platform
What document is used for final construction items? Select one: a.punchlist b.procurement list c.pick list d.performance list
a. punchlist
For this project, electrical specifications on the plumbing plans call for use of ___. Select one: a.rigid or PVC b.metallic conduits c.watertight conduits d.IMC
a. rigid or PVC
When installing electrical components on or through a roof, it is important that the electrician wait to complete his or her raceway until after the ___. Select one: a.roof jack is installed b.roofing material is installed c.penetrations are sealed d.exhaust fans are secured
a. roof jack is installed
Sheet 10B is the security device plan. What does it not define? Select one: Sheet 10B is the security device plan. What does it not define? Select one: a.security device manufacturer b.location of cameras c.location of door contacts d.location of keypads
a. security device manufacturer
When making voltage measurements, you should ___. Select one: a.set the meter on a surface b.hold the meter in your left hand c.hold the meter in your right hand
a. set the meter on a surface
What is ductwork typically made of? Select one: a.sheet metal b.copper c.aluminum d.PVC
a. sheet metal
The member that is secured to the foundation is called? Select one: a.sill plate b.foundation plate c.joist plate d.king stud
a. sill plate
Which is a very low-cost foundation type? Select one: a.slab on grade b.A-frame c.floating d.pier and beam
a. slab on grade
Per the drawings, where is the meter base to be located? Select one: a.south exterior wall b.north exterior wall c.in the basement d.west exterior wall
a. south exterior wall
Cover plates for switches shall be ___. Select one: a.stainless steel b.nylon c.acrylic d.ceramic
a. stainless steel
For the Wendy's project, the proposed underground electrical and phone will cross ___. Select one: a.storm and sanitary sewer piping b.water supply piping c.natural gas and water piping d.sanitary sewer piping only
a. storm and sanitary sewer piping
What is the 6″ PVC conduit near the pick-up window on 15A for? Select one: a.syrup lines b.electrical power c.electrical control d.floor drains
a. syrup lines
Depending on the application, there are several options to seal penetrations. Which technique is not a method? Select one: a.tape b.rubber linkage c.grout d.putty
a. tape
Who furnishes the communication system? Select one: a.the owner b.the equipment supplier c.the EC d.the GC
a. the owner
Qualified persons need ___ and knowledge of equipment and hazards to work safely. Select one: a.training b.education c.experience d.none of these
a. training
There are ___ types of lumber used in construction. Select one: a.two b.three c.four d.five
a. two
On E-2, the F31 fixture is most likely ___. Select one: a.wall-mounted b.a lay-in trougher c.pendant-mounted d.ceiling-mounted
a. wall-mounted
Match the following nominal stud size to its actual size: 3/4" × 1 1/2" Select one: a. 1 × 2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
a. 1 × 2
Match the following symbol with the term: 3 Way Switch Select one: a. s3 b. T c. II GFCI d. S e. > f. II
a. S3
What size is the incoming gas pipe? Select one: a.1.5″ b.1.25″ c.2″ d.1″
b. 1.25″
If the boxes in the wall exceed 24″ horizontally but exceed a total of ___ square inches in the same cavity firestopping must be installed. Select one: a.50 b.100 c.68 d.220
b. 100
What is the distance between the porch lights? Select one: a.3′ 6″ b.11′ 8″ c.7′ 6″ d.22′ 8″
b. 11′ 8″
On sheet A-1.0, what is the room number for the mechanical room? Select one: a.146 b.147 c.148 d.149
b. 147
NFPA 70E was first published by the National Fire Protection Association in ___. Select one: a.1776 b.1979 c.1976 d.1978
b. 1979
The civil plan for the Wendy's restaurant shows a scale of ___. Select one: a.1:10 b.1:20 c.1:30 d.1:40
b. 1:20
How many Type "B" fixtures are to be installed in the hallway? Select one: a.1 b.2 c.3 d.4
b. 2
Which conductors go to the illuminated sign near the entrance? Select one: a.3 #10 b.2 #8, 1 #10 c.3 #8 d.not specified
b. 2 #8, 1 #10
What is the total length of the building? Select one: a.74′ 0″ b.225′ 0″ c.135′ 4" d.198′ 0″
b. 225′ 0″
The maximum permissible noise exposure level, at 97 db, is ___ hours. Select one: a.6 b.3 c.4 d.8
b. 3
Per the drawings, how many receptacles are to be installed in Bedroom #1? Select one: a.3 b.4 c.5 d.6
b. 4
How many receptacles are shown in Bedroom #2? Select one: a.6 b.5 c.4 d.3
b. 5
What is the permissible exposure level (PEL), in micrograms, for crystalline silica for an 8 hour shift? Select one: a.40 b.50 c.60 d.80
b. 50
How many type "L" fixtures are shown? Select one: a.8 b.6 c.4 d.2
b. 6
Which division will have specs for the walk-in freezer? Select one: a.4 b.6 c.7 d.2
b. 6
When setting the range on a DMM for a voltage measurement, if the expected voltage to be measured is 480 volts DC, the range setting should be set on ___. Select one: a.600 V ~ b.600 V - c.2 V - d.200 V - e.20 V - f.200 V ~
b. 600 V -
What is the elevation of the finished floor? Select one: a.774.70 b.775.50 c.774.55 d.775.45
b. 775.50
What is the average lighting level calculated for the site lighting? Select one: a.2.69 b.8.07 c.7.23 d.3.0
b. 8.07
Which degree of angle is preferred when passing through a structural concrete beam? Select one: a.15 b.90 c.45 d.30
b. 90
What percentage of compaction must the soil be returned to where concrete is to be poured? Select one: a.85% b.95% c.100% d.50%
b. 95%
Which conductor material has a higher resistance? Select one: a.CU b.AL
b. AL
What are the scale types found on drawings? Select one: a.Electrical/Mechanical b.Architectural/Engineering c.Architectural/Electrical d.General/Engineering
b. Architectural/Engineering
The electric duct heater is installed in which room? Select one: a.Hallway 208 b.Bath 205 c.Stair 200 d.Office 215
b. Bath 205
Which panel contains the starters? Select one: a.A b.CP c.C d.B
b. CP
Which conductor has lower resistance? Select one: a.AL b.CU
b. CU
CMU is the acronym for ___. Select one: a.Certified Measurement Unit b.Concrete Masonry Unit c.Complete Mapping Unit d.Certified Moisture Unit
b. Concrete Masonry Unit
One-line diagrams are found in which drawings? Select one: a.Mechanical b.Electrical c.Fire Alarm d.Fire Protection
b. Electrical
In residential construction, who typically sizes the service? Select one: a.Registered Engineer b.Electrician c.Utility Company d.Homeowner
b. Electrician
Chemical manufacturers and importers shall obtain or develop SDS sheets for each hazardous chemical they produce or import. These SDS sheets shall be written in ___. Select one: a.German b.English c.French d.Japanese e.Spanish f.all of these
b. English
What does LFNC stand for? Select one: a.Liquidtight Flexible New Conduit b.Liquidtight Flexible Nonmetallic Conduit c.Lightweight Flexible Nonmetallic Conduit d.Lightweight Flexible New Conduit
b. Liquidtight Flexible Nonmetallic Conduit
MEP is the acronym for ___. Select one: a.Multiple Electrical Products b.Mechanical, Electrical, and Plumbing c.Multiple Electrical Penetrations d.Machinery, Electrical, and Plumbing
b. Mechanical, Electrical, and Plumbing
For this project, Division 15 is for ___. Select one: a.Specialties b.Mechanical, Plumbing, and HVAC c.Lighting d.Electrical
b. Mechanical, Plumbing, and HVAC
The electrical plan is designated as ___. Select one: a.Plan A b.Plan E c.Plan FA d.Plan S
b. Plan E
What is insulation rated by? Select one: a.weight b.R-value c.thickness d.type
b. R-value
What drawings show the steel erections and foundations? Select one: a.Civil b.Structural c.Plumbing d.Architectural
b. Structural
Who is typically required to warranty the roof against leaks? Select one: a.The contractor who penetrates it b.The roofer c.The general contractor d.Roofs do not require leak warranties
b. The roofer
On E-2, the F1 fixture is most likely ___. Select one: a.wall-mounted b.a lay-in trougher c.pendant-mounted d.ceiling-mounted
b. a lay-in trougher
When doing the conduit/wiring take-offs, most companies use ___ to calculate the length of the run. Select one: a.a calculator b.a measuring wheel c.an apprentice d.computer software
b. a measuring wheel
Multi-story construction typically uses what type of framing? Select one: a.platform b.balloon c.post and beam d.A-frame
b. balloon
Using ___ eliminates the need for drilling after the concrete sets and after the forms are removed. Select one: a.concrete anchors b.cast-in concrete anchors c.powder-actuated anchors d.masonry anchors
b. cast-in concrete anchors
Employers shall maintain any safety data sheets (SDSs) for hazardous ___. Select one: a.activities b.chemicals c.locations d.energy
b. chemicals
CP is the acronym for ___. Select one: a.contracting professional b.control panel c.circuit path d.concrete pole
b. control panel
What is used to elevate the RTU off of the roof? Select one: a.roof jack b.curb c.gutter d.no one elevates RTU's
b. curb
What is important when sealing a penetration in a fire rated wall? Select one: a.color of sealant b.fire rating of sealant c.diameter of penetration d.none of these
b. fire rating of sealant
Steel framing compared to wood is? Select one: a.not as strong b.fire resistant c.less expensive d.none of these
b. fire resistant
Per NEC® Section 300.21, openings around electrical penetrations must be sealed using approved ___. Select one: a.putty b.firestopping methods c.adhesive d.spray foam
b. firestopping methods
Generally, the ___ plans show little to no electrical equipment, material, or devices. Select one: a.mechanical b.foundation and structural c.grading and general utility d.HVAC
b. foundation and structural
What could occur if we do not maintain proper spacing between our wiring methods and the plumbers' installation? Select one: a.cross contamination b.galvanic action c.insulation breakdown d.current leakage
b. galvanic action
Why is it important to know the final finish type? Select one: a.general knowledge b.get correct box depth c.order fasteners d.none of these
b. get correct box depth
Which type of jobsite condition may increase electrical labor and installation costs? Select one: a.climate b.high ceilings c.material used for framing d.temperature
b. high ceilings
The fire alarm device in room 107 is most likely a ___. Select one: a.pull station b.horn-strobe c.smoke detector d.remote anunciator
b. horn-strobe
The equipment plan lists each piece of equipment ___. Select one: a.in alphabetical order b.in numerical order c.in size order d.by quantity
b. in numerical order
If an employer permits them to be worn off the job, the employer ___ required to pay for steel-toed shoes. Select one: a.is b.is not
b. is not
In a building with a basement, ___ support the floor above. Select one: a.plywood b.joists c.trusses d.posts
b. joists
According to the topographical survey of this project, ___ is/are required to be removed. Select one: a.an existing housing structure b.lighting poles c.a utility pole d.fencing
b. lighting poles
What electrical tests are required? Select one: a.continuity b.megger c.high-pot d.load
b. megger
Employee training shall include the ___ and observations that may be used to detect the presence or release of a hazardous chemical in the work area. Select one: a.information b.methods c.type d.all of these
b. methods
Which of the following is considered a hardwood? Select one: a.pine b.oak c.cedar d.fir
b. oak
Per the NEC®, a minimum of ___ receptacle(s) is required at the front of the house and at the back of the house. Select one: a.zero b.one c.two d.three
b. one
A single family dwelling is defined as "a structure that is complete in ___ unit and ___ attached to another dwelling unit by common walls." Select one: a.two, not b.one, not c.one, is d.multiple, is
b. one, not
The type of foundation where cables are used to strengthen the concrete is? Select one: a.slab on grade b.post tension slab c.structural concrete d.none of these
b. post tension slab
Which is the number one assassin of profitability? Select one: a.swine flu b.rework c.bird flu d.measles
b. rework
A "live load" is a load that is expected to change. An example of a live load is ___. Select one: a.the weight of the building b.snow or ice accumulation c.landscaping d.the framing of the building
b. snow or ice accumulation
On A5.0 section 4, the detail is looking in what direction? Select one: a.north b.south c.east d.west
b. south
Where there are discrepancies between specifications and the drawings, ___. Select one: a.the drawings take precedence over the specifications b.specifications take precedence over the drawings c.the general contractor takes precedence over the drawings and specifications d.the architect takes precedence over the drawings and specifications
b. specifications take precedence over the drawings
What is the cover plate material for Room 106? Select one: a.nylon b.stainless steel c.ivory d.acrylic
b. stainless steel
The TVSS shown in the electrical is a ___? Select one: a.television and security system b.surge suppressor c.television and sound system d.none of these
b. surge suppressor
Who furnished heating units? Select one: a.the GC b.the MC c.the EC d.the owner
b. the MC
Which schedule is the most important for the electrician? Select one: a.the finish schedule b.the panel schedule c.the fixture schedule d.the power schedule
b. the panel schedule
There are ___ chapters in the 2021 edition of NFPA 70E. Select one: a.two b.three c.four d.five
b. three
On sheet 11, the receptacle heights shown are ___. Select one: a.to the bottom of the box b.to the center of the box c.to the top of the box d.not specified in the plans
b. to the center of the box
VTR is the acronym for ___. Select one: a.volts to rear b.vent to roof c.via the railing d.vent toward rear
b. vent to roof
Safety data sheets must be readily accessible when employees are in their ___. Select one: a.break area b.work area c.work vehicle d.none of these
b. work area
Written Energized Electrical ___ are required if live parts can not be put in an electrically safe condition. Select one: a.work orders b.work permits c.job requests d.none of these
b. work permits
Match the following nominal stud size to its actual size: 1 1/2" × 1 1/2" Select one: a. 1 × 2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
b. 2 × 2
Match the following symbol with the term: Thermostat Select one: a. s3 b. T c. II GFCI d. S e. > f. II
b. T
How big is the fire service line? Select one: a.4″ b.6″ c.3″ d.8″
b. 6
What size conduit is required to the junction box near the register? Select one: a.1″ b.3/4″ c.11/2″ d.2″
c. 11/2″
What is the power required for the exhaust fans? Select one: a.208V, 3ph b.208V, 1ph c.115V, 1ph d.120V, 3ph
c. 115V, 1ph
What is the required electrical circuit for EF-1? Select one: a.120V, 1ph b.208V, 1ph c.208V, 3ph d.120V, 3ph
c. 208V, 3ph
What is the minimum distance apart boxes in the same wall cavity of a fire rated wall must be spaced to eliminate the need for firestopping? Select one: a.8″ b.18″ c.24″ d.12″
c. 24″
Which of the following is the spec division for electrical? Select one: a.22 b.23 c.26 d.27
c. 26
What size is the domestic water line? Select one: a.4″ b.6″ c.2″ d.8″
c. 2″
Which sheet depicts a typical wall detail? Select one: a.4 b.2 c.3 d.1
c. 3
The light fixture plan for Room 306 contains ___ Type K luminaires. Select one: a.9 b.7 c.4 d.2
c. 4
If we offer a VE (value engineered) option to the client, what size aluminum wire would we install for the service? Select one: a.1/0 b.250 kcmil c.4/0 d.2/0
c. 4/0
How many lighting contactors are required? Select one: a.3 b.4 c.5 d.2
c. 5
How many lighting poles are required for the site lighting? Select one: a.2 b.3 c.5 d.6
c. 5
What size circuit is specified for the oven? Select one: a.30A b.40A c.50A d.60A
c. 50A
In Room 306, luminaires are spaced approximately ___ apart in both directions around five junction boxes. Select one: a.4 inches b.5 inches c.6 inches d.8 inches
c. 6 inches
What is the mounting height of the kitchen clock receptacle? Select one: a.60″ b.84″ c.72″ d.48″
c. 72″
Refer to Figure 201.1M. You have a 50-watt load operating at 9 volts DC. To most accurately measure the current in this circuit, you should insert the red lead into the jack marked ___. Select "N/A" if the meter capacity will be exceeded. Select one: a.V Ω Hz b.COM c.A d.mA e.N/A
c. A
Drawing standards for symbols have been developed by ___. Select one: a.OSHA b.ASHRAE c.ANSI d.ASTM
c. ANSI
1/4″ equals 1 foot is what type of scale? Select one: a.Engineering b.Civil c.Architectural d.both a and b
c. Architectural
From the equipment schedule on sheet 9, what is the "ES"? Select one: a.Electrical Specialty contractor b.Engineering Service contractor c.Equipment Supplier d.Electrical Contractor
c. Equipment Supplier
What is the wall finish in the preparation areas? Select one: a.paneling b.painted drywall c.FRP d.tile
c. FRP
Which of the following provides the information for light types? Select one: a.RCP b.Device schedule c.Fixture schedule d.Panel schedule
c. Fixture schedule
Per the NEC®, all receptacles in this residence's basement must have ___. Select one: a.AFCI protection b.surge protection c.GFCI protection d.faceplates
c. GFCI protection
Which mechanical drawings show the ceiling registers and diffusers? Select one: a.all mechanical drawings b.M5 & M6 c.M1 & M2 d.none of these
c. M1 & M2
What controls the receptacles on the north wall of the family room? Select one: a.Switch b.Timeclock c.Nothing, they are always on d.There are no receptacles on the north wall
c. Nothing, they are always on
NFPA 70E rules are used by ___ to support citations relating to electrical hazards. Select one: a.fire marshalls b.inspectors c.OSHA d.police
c. OSHA
Who installs the owner provided items? Select one: a.General Contractor b.Associated Trade c.Owner d.Day Laborer
c. Owner
___ is a foundation type commonly found in areas where soil conditions cause an almost constant shift, which could lead to structural damage. Select one: a.Post-tension slab b.Slab-on-grade c.Pier and beam d.Structural concrete slab
c. Pier and beam
Which drawings have water piping and drains? Select one: a.Civil b.Structural c.Plumbing d.Architectural
c. Plumbing
What does PVC stand for? Select one: a.High Density Polyethylene b.Crosslinked Polyethylene c.Polyvinyl Chloride d.Post Vinyl Composite
c. Polyvinyl Chloride
Which type of plan has receptacles? Select one: a.Architectural b.Structural c.Power Plan d.RCP
c. Power Plan
Where is the elevator equipment located? Select one: a.Room 114 b.Room 141 c.Room 214 d.Room 212
c. Room 214
Which sheet is the security device plan? Select one: a.Sheet 2 b.Sheet F1 c.Sheet 10B d.Sheet 8
c. Sheet 10B
On what sheet are found the details of site lighting pole foundations? Select one: a.Sheet 6 b.Sheet 7 c.Sheet 2 d.Sheet 10A
c. Sheet 2
This building style is typical for which part of the United States? Select one: a.Pacific Northwest b.North East c.Southern d.Eastern
c. Southern
___ is the practice of reviewing contract documents, including the prints and specifications, to determine the quantities of materials to be included in a bid. Select one: a.Request for Information (RFI) b.Request for Proposal (RFP) c.Takeoff d.Drafting
c. Takeoff
What is the nominal size of lumber? Select one: a.The size after surfacing and drying b.The size lumber is surfaced to c.The size prior to surfacing and drying d.Random numbers meant to confuse
c. The size prior to surfacing and drying
How are electrical boxes sized? Select one: a.number of conductors b.raceway size(s) c.a and b d.no sizing required
c. a and b
If fixtures are scheduled to be installed in the bathroom, they must be listed for ___. Select one: a.a damp location b.a dry location c.a wet location d.a special location
c. a wet location
On E-2, the F6 fixture is most likely ___. Select one: a.wall-mounted b.a lay-in trougher c.an emergency light d.ceiling-mounted
c. an emergency light
Personal Protective Equipment shall be worn as ___ for the risks involved. Select one: a.specified b.necessary c.appropriate d.all of these
c. appropriate
Employers shall ensure that employees are provided with ___ to the extent necessary to protect them in the event of a spill or leak of a hazardous chemical. Select one: a.training b.information c.both a & b d.neither a nor b
c. both a & b
All personal protective equipment shall be of maintained and ___ condition. Select one: a.sanitary b.reliable c.both a and b d.neither a nor b
c. both a and b
The fans in the indoor boarding area are ___. Select one: a.switch-operated b.fed from LP4 c.both a and b d.none of these
c. both a and b
What is required for acceptance of HVAC systems? Select one: a.system report b.balancing complete c.both a and b d.none of these
c. both a and b
Which type of anchors are installed prior to pouring the concrete? Select one: a.compressed gas anchors b.masonry anchors c.cast-in concrete anchors d.concrete anchors
c. cast-in concrete anchors
Type "C" drawings are: Select one: a.concrete drawings b.contour drawings c.civil drawings d.culvert drawings
c. civil drawings
What does PEX stand for? Select one: a.polyvinyl chloride b.plastic exchanger c.crossliked polyethylene d.flame resistant plastic
c. crossliked polyethylene
What is the danger with using compressed air driven fasteners with masonry? Select one: a.high pressure b.low pressure c.damage to masonry d.none of these
c. damage to masonry
Which type of service(s) is typically installed for residential buildings? Select one: a.overhead b.underground c.either a or b d.neither a nor b
c. either a or b
The FACP shown in room 219 is ___. Select one: a.part of the security system b.IT equipment c.fire alarm panel d.facility access control panel
c. fire alarm panel
When securing to pressure-treated lumber, it is recommended to use ___. Select one: a.wood screws b.steel screws c.galvanized fasteners d.composite fasteners
c. galvanized fasteners
An example of a commercial project that may have classified areas is a ___. Select one: a.bakery b.retail clothing store c.gasoline station d.home improvement store
c. gasoline station
When using a Digital Multimeter (DMM) and applying Ohm's Law to measure current, if the resistance is decreased, current ___. Select one: a.is decreased b.remains the same c.is increased d.goes to zero e.none of these
c. is increased
Per the drawings, where is the panel to be located? Select one: a.living room b.carport c.kitchen closet d.basement
c. kitchen closet
Finishes required for the restaurant include all of the below except ___. Select one: a.brick b.carpeting c.landscaping d.tile
c. landscaping
The photometric drawing is typically done by the ___. Select one: a.architect b.electrician c.lighting designer d.interior designer
c. lighting designer
Employees must be informed of any operations in their work area where hazardous chemicals are present, and the ___ and availability of the written Haz Com program, including the required list(s) of hazardous chemicals and MSDS sheets. Select one: a.cost b.purpose c.location d.none of these
c. location
Which material is most resistant to damage by fire? Select one: a.PVC b.wood c.metal d.plexiglass
c. metal
On the grading/utility plan, where does incoming water come from? Select one: a.south side b.east side c.north side d.west side
c. north side
Many franchise restaurants are ___. Select one: a.completed by the same contractor b.completed on the same timeline c.of the same layout and design d.of different layout and design
c. of the same layout and design
Which method of framing is more of an open structure with exposed timber members? Select one: a.platform b.balloon c.post and beam d.A-frame
c. post and beam
Per NEC® Section 300.4(E), boxes and raceways installed under roof decking must be ___. Select one: a.weatherproof b.made of composite material c.protected from physical damage d.watertight
c. protected from physical damage
Liquidated damages are ___. Select one: a.related to rain damages b.related to flooding damage c.related to unexcused delays in completion d.all of these
c. related to unexcused delays in completion
SCCR is the acronym for ___. Select one: a.singular current circuit rating b.single circuit current rating c.short circuit current rating d.stranded circular circuit rating
c. short circuit current rating
The brick veneer residence is a ___. Select one: a.multifamily residence b.commercial facility c.single-family residence d.duplex residence
c. single-family residence
How do you access the basement? Select one: a.scuttle hole in the closet b.exterior entrance c.stairs in the carport d.there is no basement
c. stairs in the carport
In light frame construction, steel may be used as ___. Select one: a.anchors b.raceway supports c.structural beams d.a finish
c. structural beams
The foundation that uses poured concrete beams is? Select one: a.slab on grade b.post tension slab c.structural concrete d.none of these
c. structural concrete
Transient voltage surge suppressor (TVSS) is an outdated term that has been replaced with the term ___. Select one: a.arc-fault circuit interrupter (AFCI) b.ground-fault circuit interrupter (GFCI) c.surge protective device (SPD) d.tamper-resistant receptacle (TRR)
c. surge protective device (SPD)
On sheet A-1.0, which way is north? Select one: a.toward the top of the plan b.toward the bottom of the plan c.toward the right of the plan d.toward the left of the plan
c. toward the right of the plan
Where do we find the interior components of a wall in the drawings? Select one: a.reflected ceiling plan b.site plan c.wall detail d.finish schedule
c. wall detail
The depth where water is found is called ___. Select one: a.frost depth b.drain depth c.water table d.rock point
c. water table
Concrete is a porous material and requires waterproofing. Which technique below is not a waterproofing method? Select one: a.tar b.membrane c.waterproof putty d.waterproof paint
c. waterproof putty
A use for steel found predominantly in commercial construction is? Select one: a.roofing b.overhead raceway supports c.web bar joist d.masonry anchors
c. web bar joist
Employers shall maintain in the ___ copies of the required MSDS sheets for each hazardous chemical. Select one: a.office b.truck c.workplace d.trailer
c. workplace
Match the following nominal stud size to its actual size: 1/2" × 3 1/2" Select one: a. 1 × 2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
c. 2 × 4
Match the following symbol with the term: GFCI Select one: a. s3 b. T c. II GFCI d. S e. > f. II
c. II GFCI
Sheetrock® is a registered tradename for ___. Select one: a.plywood b.fiber-reinforced plastic c.insulation d.gypsum board
d .gypsum board
Which fixture Type is to be installed above the basin in the bathrooms? Select one: a."J" b."K" c."L" d."M"
d. "M"
The term "take-off" refers to ___. Select one: a.the project officially "taking off" (beginning) b.the process of removing unwanted materials c.roughing-in electrical d."taking off" (counting) the number of electrical components shown on a set of plans
d. "taking off" (counting) the number of electrical components shown on a set of plans
What is the General Liability Insurance requirement? Select one: a.$1,000,000 b.$10,000,000 c.$500,000 d.$100,000
d. $100,000
How many receptacles are to be installed in EACH bathroom? Select one: a.4 b.3 c.2 d.1
d. 1
What is the specified warranty of HVAC systems? Select one: a.2 years b.6 months c.90 days d.1 year
d. 1 year
What number is the electrical room? Select one: a.150b b.151 c.151a d.152
d. 152
For the Wendy's project, what is the scale on the civil drawings? Select one: a.1″ = 30′ b.1/8″ = 1′-0″ c.1″ = 40′ d.1″ = 20′
d. 1″ = 20′
How many cavities does a typical masonry block contain? Select one: a.1 b.3 c.4 d.2
d. 2
Which division will have specs for excavation? Select one: a.1 b.10 c.16 d.2
d. 2
Per the specifications, what size service is to be installed? Select one: a.100A b.60A c.83A d.200A
d. 200A
How deep is the underground conduit to the bollard? Select one: a.36″ b.30″ c.60″ d.24″
d. 24″
Which of the following is the spec division for communications? Select one: a.22 b.23 c.26 d.27
d. 27
How may receptacles are shown on the exterior? Select one: a.6 b.5 c.4 d.3
d. 3
Which sheet number provides the plan for the site? Select one: a.1 b.3 c.2 d.4
d. 4
What is the total connected load amps? Select one: a.178 b.600 c..9 d.548
d. 548
What is the elevation of the first floor? Select one: a.652.40 b.652.55 c.646.6 d.652.60
d. 652.60
How many light fixtures are required for the site lighting? Select one: a.2 b.4 c.5 d.9
d. 9
Which method of framing has a very steep pitch? Select one: a.platform b.balloon c.post and beam d.A-frame
d. A-frame
Which drawing type would have floor plans and finishes? Select one: a.Civil b.Structural c.Plumbing d.Architectural
d. Architectural
Which are panel types? Select one: a.MLO b.MCB c.MLB d.Both a and b
d. Both a and b
A plot plan typically has what type of scale? Select one: a.Architectural b.General c.Combination d.Civil
d. Civil
Which drawings usually show site lighting? Select one: a.Mechanical b.Architectural c.Fire Alarm d.Civil
d. Civil
Which type of PVC do plumbers use for venting? Select one: a.DWC b.DWE c.DWP d.DWV
d. DWV
For this project, Division 16 is for ___. Select one: a.Specialties b.Mechanical, Plumbing, and HVAC c.Lighting d.Electrical
d. Electrical
What does FRP stand for? Select one: a.Fire Resistive Plastic b.Flame Retarndant Plastic c.Fiber Reinforced PVC d.Fiber Reinforced Plastic
d. Fiber Reinforced Plastic
Which drawings have sprinkler piping? Select one: a.Mechanical b.Electrical c.Fire Alarm d.Fire Protection
d. Fire Protection
Who is responsible for setting kitchen equipment in place? Select one: a.owner b.equipment supplier c.EC d.GC
d. GC
Who provides the fixtures to be installed in the living room, on either side of the fireplace? Select one: a.Supply House b.Electrician c.General Contractor d.Owner
d. Owner
Which of the following provides information for the circuiting to the receptacles and lights? Select one: a.RCP b.Device schedule c.Fixture schedule d.Panel schedule
d. Panel schedule
RFP is the acronym for ___. Select one: a.Request for Proposal b.Request for Personnel c.Request for Products d.Request for Pricing
d. Request for Pricing
What kind of sink is to be installed in Exam rooms 1 through 9? Select one: a.S5 b.S6 c.S3 d.S1
d. S1
On what sheet are the details of signage foundations with conduits? Select one: a.Sheet 6 b.Sheet 7 c.Sheet 2 d.Sheet 10A
d. Sheet 10A
Where is the date of the drawing found? Select one: a.Legend b.Drawing scale c.Architectural drawings only d.Titleblock
d. Titleblock
Underground water-supply piping must be ___. Select one: a.PVC b.CPVC c.Type L copper d.Type K copper
d. Type K copper
The electrical drawing shows ___. Select one: a.an incoming water service b.overhead electrical lines c.x-ray equipment d.a location for a generator
d. a location for a generator
A comprehensive Haz Com program includes ___. Select one: a.other forms of warning b.employee training c.SDS training d.all of these
d. all of these
At each workplace, employers shall ___ a written hazard communication program. Select one: a.implement b.maintain c.develop d.all of these
d. all of these
Electrical penetrations can be sealed with? Select one: a.caulk b.grout c.foam d.all of these
d. all of these
Employees shall be provided with eye and face protection when machines or operations present potential eye or face injury from ___. Select one: a.physical injury b.radiation agents c.chemicals d.all of these
d. all of these
Employees whose occupation or assignment requires exposure to laser beams shall be furnished with suitable laser safety goggles. This protective equipment shall bear a label identifying the ___. Select one: a.visible laser light transmission b.optical density of laser wavelengths c.laser wavelengths for which use is intended d.all of these
d. all of these
Masonry can be used for: Select one: a.walls b.foundations c.facades d.all of these
d. all of these
PPE is required for head, face, neck, ___, hands, arms, feet and legs. Select one: a.chin b.body c.eyes d.all of these
d. all of these
Personal protective equipment for ___ and extremities shall be used and maintained. Select one: a.hands b.eyes c.face d.all of these
d. all of these
The ATS is most likely ___. Select one: a.connected to the generator b.connected to the MDP c.connected to the GP2 d.all of these
d. all of these
Which of the following are roofing types? Select one: a.membranes b.gravel c.asphalt shingles d.all the above
d. all the above
Employees whose vision requires use of corrective lenses in spectacles shall be provided with eye protection in the form of ___. Select one: a.optically corrected spectacles b.goggles with corrective lenses c.over-spectacle-type goggles d.any of these
d. any of these
Employees working in areas where there is a possible danger of head injury caused by ___ shall be protected by protective helmets. Select one: a.falling or flying objects b.impact c.electrical shock d.any of these
d. any of these
Protective clothing or equipment shall be utilized when exposure to a hazard could cause impairment in the function of any part of the body through ___. Select one: a.inhalation b.physical contact c.absorption d.any of these
d. any of these
The chemical distributor, manufacturer, or importer shall ensure that each container of hazardous chemical leaving the workplace has the identity of the hazardous chemical. Select one: a.labeled b.marked c.tagged d.any of these
d. any of these
Equipment and mechanical drawings are typically drawn by the ___. Select one: a.electrical contractor b.structural engineer c.civil engineer d.architect
d. architect
Colors of switches, receptacles, and cover plates are typically found on the ___. Select one: a.photometric drawing b.mechanical drawing c.electrical drawing d.architectural drawing
d. architectural drawing
Chemical-specific information must always be ___ through labels and MSDS sheets. Select one: a.on hand b.ready c.forwarded d.available
d. available
Similar to stainless steel, if FRP is properly maintained, it can inhibit what? Select one: a.fire b.squirrels c.stains d.bacteria
d. bacteria
What is the wall finish in the dining room? Select one: a.paneling b.vinyl fabric c.tile d.both a and b
d. both a and b
What material is to be used for framing members? Select one: a.Douglas Fir b.#2 Yellow Pine c.Blue Spruce d.both a and b
d. both a and b
Tables and ___ are provided for use when Arc Flash studies have not been performed. Select one: a.chairs b.tools c.plans d.charts
d. charts
Which type of anchors require drilling? Select one: a.compressed gas anchors b.masonry anchors c.cast-in concrete anchors d.concrete anchors
d. concrete anchors
What connector is needed to the fry dump station? Select one: a.receptacle b.disconnect switch c.duplex d.direct connect
d. direct connect
What is the biggest "competitor" to the electrical installation when related to ceiling and overhead spaces? Select one: a.fire alarm systems b.plumbing systems c.low voltage systems d.ductwork systems
d. ductwork systems
Employers shall provide employees with ___ information and training on hazardous chemicals in the work area at the time of their initial assignment. Select one: a.timely b.occasional c.worthwhile d.effective
d. effective
Masonry may be used for walls, foundations, and ___. Select one: a.bathrooms b.driveways c.patios d.facades
d. facades
What kind of notes relate to an entire sheet or set of drawings? Select one: a.key notes b.spec notes c.footnotes d.general notes
d. general notes
From the equipment schedule on sheet 9, what does the EC install? Select one: a.hot water tank b.POS terminal c.quad booth d.hand dryers
d. hand dryers
From the equipment schedule on sheet 9, what does the EC supply? Select one: a.hot water tank b.POS terminal c.quad booth d.hand dryers
d. hand dryers
Penetrations in steel beams or columns ___. Select one: a.can be made anywhere b.do not affect the strength of the steel c.do not require approval d.may cause failure
d. may cause failure
When working on live or energized equipment, conductive ___ is permitted to be worn. Select one: a.clothing b.jewelry c.either a or b d.neither a nor b
d. neither a nor b
On the Topographical Survey, what is the scale? Select one: a.1″ = 100′ b.1/8″ scale c.1″ = 50′ d.none of these
d. none of these
The "VP" device in the first-floor mechanical room is fed from ___. Select one: a.LP3 b.LP2 c.time clocks d.none of these
d. none of these
What is the largest capacity RTU? Select one: a.RTU1 b.RTU3 c.RTU7 d.none of these
d. none of these
What is the voltage of the heater? Select one: a.208, 3ph b.240, 3ph c.208, 1ph d.none of these
d. none of these
Where does heat come from in Vestibule 144? Select one: a.RTU1 b.RTU4 c.RTU7 d.none of these
d. none of these
Which panel has the contactors for the fryer? Select one: a.CP b.Main c.B d.none of these
d. none of these
How many days are specified for completion? Select one: a.5 b.60 c.120 d.not specified
d. not specified
Who is responsible for removing the light poles? Select one: a.the owner b.the EC c.the GC d.not specified
d. not specified
On this project, Division 1 contains ___. Select one: a.specifications for site construction b.specifications for moisture protection c.specifications for finishes d.overall project description, location, and requirements
d. overall project description, location, and requirements
For the contractor to plan the outdoor conduit and number of circuits, information on the ___ and electrical panel schedule must be reviewed. Select one: a.structural plan b.MEP plan c.NEC® Annex C d.photometric plan
d. photometric plan
Which foundation type is used when soil conditions change? Select one: a.slab on grade b.A-frame c.floating d.pier and beam
d. pier and beam
The simplest and most common form of framing is ___. Select one: a.post and beam b.A-frame c.balloon d.platform
d. platform
The ___ plan shows the compass direction of the building. Select one: a.floor b.elevation c.compass d.plot
d. plot
RFP typically means ___. Select one: a.reinforced partition b.rounded furniture post c.request from plumber d.request for pricing/proposal
d. request for pricing/proposal
What is the actual name for a "Witch's Hat"? Select one: a.fireworks b.top hat c.RTU curb d.roof jack
d. roof jack
The gauge of a metal stud determines the ___ of the stud. Select one: a.type of metal b.finish c.shape d.thickness
d. thickness
Which is a industry best practice or preferred method to bring power to a RTU? Select one: a.roof penetration b.wirelessly c.surface mount on the roof d.through the curb
d. through the curb
What is the wall finish in the restrooms? Select one: a.paneling b.painted drywall c.FRP d.tile
d. tile
TD is the acronym for ___. Select one: a.toilet drain b.touchdown c.touch device d.trench drain
d. trench drain
The fixtures shown with hash marks are most likely ___. Select one: a.wall-mounted b.lay-in troughers c.emergency lights d.unswitched
d. unswitched
Aside from paint, there are many other interior finishes. What is an example of an interior finish? Select one: a.orange-peel texture b.stucco c.water-resistant drywall d.wood paneling
d. wood paneling
Match the following nominal stud size to its actual size: 1 1/2" × 5 1/2" Select one: a. 1 × 2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
d. 2 × 6
Match the following symbol with the term: Single Pole Switch Select one: a. s3 b. T c. II GFCI d. S e. > f. II
d. S
Employers shall ensure that labels on incoming containers of hazardous chemicals are not ___.I. removed II. outdated III. defaced Select one: a.I, II & III b.I & II only c.I only d.II only e.I & III only f.III only
e. I & III only
Face and eye protection equipment shall ___. Select one: a.be reasonably comfortable when worn under the designated conditions b.fit snugly and shall not unduly interfere with the movements of the wearer c.be easily cleanable and capable of being disinfected d.provide adequate protection against the particular hazards for which they are designed e.all of these f.none of these
e. all of these
Match the following nominal stud size to its actual size: 1 1/2" × 7 1/4" Select one: a. 1 × 2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
e. 2 × 8
Match the following symbol with the term: Phone Outlet Select one: a. s3 b. T c. II GFCI d. S e. > f. II
e. >
Match the following nominal stud size to its actual size: 1 1/2" × 11 1/4" Select one: a. 1 ×2 b. 2 × 2 c. 2 × 4 d. 2 × 6 e. 2 × 8 f. 2 × 12
f. 2 × 12
Match the following symbol with the term: Duplex Receptacle Select one: a. s3 b. T c. II GFCI d. S e. > f. II
f. II
Which of the following is the spec division for HVAC? Select one: a.22 b.23 c.26 d.27
b. 23
How many bedrooms are to be built? Select one: a.2 b.3 c.1 d.5
b. 3
What is the thickness of the gypsum board to be installed? Select one: a.1/4" b.5/8" c.1/2" d.3/4"
c. 1/2"
What specification division for the Brick Residence includes the requirements for Electrical? Select one: a.26 b.8 c.16 d.5
c. 16
When a CE marking appears on a piece of equipment, this marking indicates that the equipment conforms to health, safety, environment and consumer protection requirements established by ___. Select one: a.the Electrotechnical Committee b.the China Export consortium c.the European Commission d.Canadian Electrical testing e.none of these
c. the European Commission
In the reading, the timeframe for completing the electrical installations in this residence is ___. Select one: a.30 days b.60 days c.100 days d.150 days
d. 150 days
