CYBR1.CAB-6 Troubleshooting Physical Connectivity (N10-008)
You have a network connected using a physical star topology. One of the drop cables connecting a workstation is removed. Which of the following best describes what happens to network communications?
All devices except the device connected to the drop cable will be able to communicate.
During a network infrastructure upgrade, you have replaced two 10 Mbps hubs with switches and upgraded from Category 3 UTP cable to Category 5e. During the process, you accidentally cut the Cat 5e patch cable that stretches from the network printer to the upgraded switch. What is the impact on the network?
All network nodes, with exception of the printer, will be available
You have decided to implement Gigabit Ethernet on your network. Each switch port is connected to a single device. Following the installation, you find one device connected to a switch that is only running at 100 Mbps. Which of the following are likely causes?
Crosstalk
You have a network using a full physical mesh topology. The link between device A and device B is broken. Which of the following best describes what happens to network communications?
Device A will be able to communicate with all other devices.
You are troubleshooting a client connectivity problem on an Ethernet network. The client system has intermittent connectivity to the network. You discover that the UTP patch cable is run 75 feet from the wall outlet, passes through the ceiling and over several florescent light fixtures before reaching the client system. Which of the following may be a cause of the connectivity problem?
EMI interference
You are creating an Ethernet network for your company. The shipping department is located in a different building that is located 150 meters from the main wiring closet. You connect a single Cat 6e cable to connect the wiring closet to the shipping building. What will be a problem with this plan?
Ethernet cable limited to 100 meters in length
You have just connected four new computer systems to an Ethernet switch using spare patch cables. After the installation only three systems are able to access the network. You verify all client network settings and replace the network card in the failed system. The client is still unable to access the network. Which of the following might you suspect as the real cause of the problem?
Failed patch cable
You are moving a client to a new location within an Ethernet network. Previous to the move, the client system did not have any difficulty accessing the network. During the relocation, you attach a patch cable from the client system to the wall jack and from the patch panel to the switch. Once connected you do not get a link light on the network card or the switch. You swap out the cable running between the patch panel and the switch with a known working one but you can still not connect. Which of the following might you suspect as the problem?
Failed patch cable between the client system and the wall jack.
Upon conducting a visual inspection of the server room, you see that a switch displays LED collision lights that are continually lit. You check the LED on the corresponding workstation and see that it is flashing rapidly even though it is not sending or receiving network traffic at that time. What is the cause of the network collision?
Faulty network card
You have a network connected using a physical bus topology. One of the cables connecting a workstation to the bus breaks. Which of the following best describes what happens to network communications?
No device is able to communicate
To press wires into a patch panel or punchdown block
Punchdown tool
A user from the Sales department calls to report that he is experiencing problems connecting to the Sales file server. All users in the Sales department connect to the Sales server through a single Ethernet switch. No other users have reported problems connecting to the Sales server. Which of the following troubleshooting actions are you most likely to perform first?
Replace the network card in the user's computer
You're responsible for implementing network cabling in a new network installation. The cabling will be installed in a manufacturing environment where there is a great deal of electromagnetic interface (EMI). Which type of cabling would operate best in this environment?
Shielded twisted pair cable. Fiber-optic cable.
You are troubleshooting a connectivity problem in which one client system is unable to connect to a server. Both the server and the client system are connected to the same Ethernet network switch. No other users have complained of a problem, and you suspect that faulty network cabling might be to blame. Which of the following troubleshooting steps are you most likely to perform first?
Use a media tester (cable tester) to test the cable between the computer and the network switch.