osha 30 module 14 personal protective equipment
Eye and face protection must be stamped _____ to indicate that the ppe meets this specification for the design. A. ansi 87.1 B. Astm 4000 C. osha 29cfr D. none
A. ansi 87.1
for hot work a leather apron is generally recommended what hand and arm ppe are generally recommended
leather gloves or gauntlets
The _________ is most often the best source of information regarding chemical protective gloves
manufacturer or supplier
this material is sometimes used for the soles of non slip footwear
neoprene
Electricians should wear ______ hand and arm protection meeting ansi spec
rubber
Engineering controls are more preferred than ppe for controlling exposure to hazards
true
individual states may enforce standards that are not identical to federal requirements
true
Hearing protection is worn to
A minimize the frequency and intensity of noise
Head protection must meet _____ specifications and be so labeled. A. ansi B. niosh c. msha D. bus
A. ansi
A bureau of labor statistics survey found that most workers who suffered impact head injuries were A. not wearing head protection B. wearing head protection incorrectly C. working with object that were to heavy D. none of the above
A. not wearing head protection
It is important to inspect head protection for signs of dents cracks penetration or any other damage, if damage is found A. report the damage and get the hard hat replaced B. place stickers on the damaged area C. paint the damaged area D. all of the above
A. report the damage and get the hard hat replaced
Flying particles cause the greatest number of eye injury cases A. true B. False
A. true
The water temperature for an emergency eye wash should be tepid in the range of 60-100 A. true b. false
A. true
injuries to arm and hands include
All of the above
which of the following is not one of the 4 primary classes eye and face protection? A. safety spectacles B. Goggles C. bump glass D. face protection E. welding shields
C bump glass
Eye injury may result from A. flying particles B. chemical exposure c. injurious light rays D. all of the above
D. all of the above
ppe is A. referred to as ppe B. Designed to create a barrier against workplace hazards C. less preferred than engineering controls D. all of the above
D. all of the above
which of the following is a reason for wearing a respirator
D. both a and b
which statement is incorrect with respect to damaged ppe A. damaged ppe must not be used B. Damaged ppe should be tagged as defective and removed C. Damaged ppe should be repaired or discarded immediately D. damaged ppe should be used until non damaged ppe can be obtained
D. damaged ppe should be used until non damaged ppe can be obtained
which statement is incorrect with respect to ppe A. pie does not eliminate the hazard B. if ppl equipment fails, exposure will occur C. Equipment must be properly fitted and maintained D. ppe is the preferred method of hazard control
D. ppe is the preferred method of hazard control
Which of the following is true owith respect to atmosphere supplying respirator
E. all of the above
eye wash stations should be located A. on the same level as the hazard B. in a well lit area that is properly marked C. within 10 seconds from the hazard D. along a path free of obstructions E. all of the above
E. all of the above
typical foot injury is caused by objects falling fewer than 4 feet with a median weight of about 65 lbs
True
Air purifying respirators can only be worn when there is
a. sufficient oxygen to support life
When the eyes or the bodies of workers may be exposed to corrosive materials OSHA requires a facility that will provide emergency flushing or drenching A. true B. false
a. true
safety footwear should have
all of the above
these are worn where there are sparks molten metal splashes why have elastic sides or quick release
b foundry boots
Emergency eye wash and shower station must be installed A. on the same level as the hazard B. along a travel path free from obstructions C. both a and b D. none of the above
c both a and b
Which is not one of the four basic types of earring protection
c rolled cotton balls
Some one whose body is exposed to injurious chemicals should flush the exposed part for A. 15 seconds B. 1 minute C. 15 minutes D. Flushing is not necessary
c. 15 minutes
which class of protective hard hat offers protection from high voltage A. class A B. classC C. class E D. class G
c. Class E
These are worn to protect the entire face from flying particles metal sparks or chemical splashes A. chemical goggles B. safety spectacles with side shields C. face shield with ansi approved safety spectacles D. both a and b
c. Face shield with ansi approved safety spectacles.
Head Protection must be A. inexpensive and eye catching B. color coded by occupation and be visible C. resistant to penetration and be able to absorb the shock of a blow D. all of the above
c. resistant to penetration and be able to absorb the shock of a blow.