SAFETY 111 FINAL
The minimum breaking strength for anchorages used in vertical lifelines two workers is _____ pounds for EACH person attached
5000
A worker on a low slope roof can work in the designated area which is not less than ___ feet from the roof edge
6
There are many situations that may cause slips, trips, and falls, for instance (select all that apply) a. Grease b. Oil c. Water d. Improper Footwear
(All apply)
Rescue procedures must be practiced once every __ months
12
A floor hole is an opening measuring less than ___ inches but more than ___ inch(es) in its least dimension, in any floor, platform, pavement, or yard, through which materials but not persons may fall.
12, 1
How long must an eyewash be able to flush a worker's eyes? 5 minutes 10 minutes 15 minutes 1 minute
15 minutes
How many parts are in an SDS?
16
What other OSHA standard specifies the eye wash? 1910.151 1910.1200 1910.132 1910.106
1910.151
Which is an example of a vertical standard?
1910.261 (Pulp, Paper, and Paperboard Mills)
A powered industrial truck is unattended when the attendant is how far from the truck? 10 feet 20 feet 15 feet 25 feet
25 feet
What is the minimum width of an exit route?
28 inches
A minimum working space around electrical panels is ___ feet
3
When using a ladder how many feet must extend above the landing point?
3
Every flight of stairs with ___ or more risers must have standard stair railings on all open sides (or standard handrails if the stairs are enclosed)
4
Every open-sided platform or wall that is ___ feet or more above the next level must be protected by a standard railing.
4
Point of operation hazard -- OSHAs enforcement policy (CPL 2-1.25) Guidelines for point of operation guarding for power press brakes. For the purpose of maintaining a "safe distance" as discussed in this instruction, the operating employee and helping employee(s) must not approach closer than necessary and in no case, closer than __ inches to the power press brake point of operation.
4
Periodic inspections of cranes may identify the following (more than one may apply): a. Deformed, cracked, or corroded members b. Loose bolts or rivets c. Cracked or worn sheaves and drums d. Worn, cracked or distorted parts (e.g. pins)
All apply
Batter charging facilities must provide for: Eye wash Fire extinguisher Protection from damage Adequate ventilation All of the above
All of the above
When using a scaffold you should never: a. Climb the bracing b. Climb the frame c. Carry tools d. All of the above
All of the above
A class __ hardhat is designed for protection against high-voltage
E
At a minimum, how often must a PIT driver be reevaluated? Every 6 months Annually Every 3 years As needed
Every 3 years
True or False: All fall protection connectors must be drop forged, formed steel or high pressure welded, and be corrosion resistant
False
True or False: Body belts are an acceptable part of a personal fall arrest system
False
True or False: Employers must have and maintain an audible employee alarm system?
False
True or False: Fire extinguishers must be within 50 feet of any combustible area.
False
True or False: The OSH Act was signed into law by President Richard Nixon on December 29, 1969
False
True or False: Each affected employee shall affix a personal lockout or tagout device to the group lockout device, group lockbox, or comparable mechanism when he or she begins work, and shall remove those devices when he or she stops working on the machine or equipment being serviced or maintained
False (each "authorized" employee)
While any employee is exposed to contact with parts of fixed electric equipment or circuits which have be de-energized, the circuits energizing the parts shall be _______ ____ or tagged or both
Locked out
What OSHA Outreach Program is a great source of help for small business?
OSHA Onsite Consultation Program
High lift trucks must be fitted with the following: Overhead guard Rollerover protection Stabilizers Hard hats
Overhead guard
Each disconnecting means must be legibly marked to indicate its _____
Purpose
What does the first S in PASS stand for?
Squeeze
______ and circuit breakers must be legibly marked
Switches
What are the maximum allowable lateral forces in a guardrail system? Toprail ____ pounds Midrail ____ pounds Toaeboard ____ pounds
Toprail __200__ pounds Midrail __150__ pounds Toeboard __50__ pounds
True or False: A general duty of the employers under the OSH Act is to furnish each of his employment and a place of employment which are free of recognized hazards that are likely to cause serious physical harm to his employees?
True
True or False: A general requirement for electrical safety is that illumination must be provided for all working spaces about service equipment
True
True or False: A workplace is permitted to have only one means of exit?
True
True or False: Company leadership must make safety and health a core value and lead by example.
True
True or False: Compressed gas cylinders must be secured to prevent them from falling over
True
True or False: Currently, OSHA's lock-out tag-out standard covers servicing and maintenance of machines and equipment in which the "unexpected" energization or start up of the machines or equipment, or release of stored energy could cause injury to employees
True
True or False: Effective communication and coordination raises awareness of contractors and staffing agencies to the hazards
True
True or False: Electrical equipment may not be used unless it is suitably marked
True
True or False: Employees should be given opportunities to participate in program design and implementation
True
True or False: Employers must develop plans with measures to protect workers during emergencies and non-routine activities
True
True or False: Employers must know all of their potential ignition sources and how to control them.
True
True or False: Other workers are never allowed to ride on the front tines of the forklift
True
True or False: Regardless of height, if a worker can fall into or onto dangerous machines or equipment, employers must provide guardrails and toeboards.
True
True or False: Storage of material must be such that the material does not create a hazard
True
True or False: The route to an exit must be clearly indentified.
True
True or False: When a truck is left unattended the load must be fully lowered, controls neutralized, power shall be shut off, and brakes set
True
True or False: You should always inspect a ladder before use.
True
True or False: You should always keep 3 points of contact with a ladder.
True
True or False: the on-site employer shall ensure that his/her employees understand and comply with restrictions and prohibitions of the outside employer's energy control program
True
True or False: Vertical Standards are specific to only a particular industry?
True, horizontal standard affects everyone equally
Employees have a right to each of the following except:
Workers may not file a complaint directly with OSHA
The following are elements of the PIT training except: Computer learning Practical exercises Evaluation Written test
Written test
Yes or No: An employer with ten employees discusses her emergency action and fire prevention plan with her employees over pizza at lunch. Is she in compliance with OSHA requirements?
Yes
When inspecting the workplace, you notice some workers wearing glasses. What designation should be on the eyewear?
Z87
Number the four levels of the hierarchy of controls listed below from most effective (1) to least effective (4): ____ Engineering controls ____ Personal Protective Equipment ____ Elimination/Substitution ____ Administration Controls
__2__ Engineering controls __4__ Personal Protective Equipment __1__ Elimination/Substitution __3__ Administration Controls
Guards are barriers which prevent access to danger areas, there are four types, match them: (photo on phone) ____ Adjustable guards ____ Interlocked Guards ____ Fixed guards ____ Self-adjusting guards
__B__ Adjustable guards __C__ Interlocked Guards __A__ Fixed guards __D__ Self-adjusting guards
As discussed in class, a significant cause of degradation of synthetic slings is from a. Acids b. Age c. Oxidation d. Cutting
a. Acids
What is the order in which sampling is performed w conducting air monitoring to assess air quality in a Permit-required space a. Oxygen, flammable, toxic b. Toxic, flammable, oxygen c. Flammable, toxic, oxygen d. Toxic, oxygen, flammable e. Flammable, oxygen, toxic
a. Oxygen, flammable, toxic
List four of the six major elements of an effective safety and health program
a. Training b. Identify hazards c. Leadership Management d. Communication
In mechanical power presses there are two types of clutches. a. _____ - revolution one that cannot be disengaged until one complete stroke is made b. _____ - revolution can disengage clutch at any point along the cycle
a. full b. part
The distance between the periphery and the adjustable tongue guard on a pedestal grinder shall never exceed ________ inch a. one-quarter b. one-half c. one-eighth d. one e. none of the above
a. one quarter
Employers must keep Safety Data Sheets readily _____________________ to workers.
accessible
A person whose job requires him/her to work in an area in which such servicing of maintenance is being performed is known as ___________________
affected employee
The two basic types of respirators are ___-purifying and ______-supplying
air, atmosphere
Flexible cords and cables shall be _______ and suitable for conditions of use and location
approved
Two types of hazards for which a permit is required are ________ and __________
atmospheric, non-atmospheric
Currently, OSHA may penalize an employer how much for one serious violation?
$12,934
An energy isolating device is/are which of the following? (more than one can apply) a. A manually operated electrical circuit breaker b. A disconnect switch c. A manually operated switch by which the conductors of a circuit can be disconnected from all ungrounded supply conductors and, d. a line valve; a block; and any similar device used to block or isolate energy
(all apply)
A few things that can be done to start a safety and health program include (circle all that apply): a. Train workers on how to identify and control hazards b. Inspect the workplace with workers c. Assign workers the task of choosing, implementing, and evaluating their solutions d. Discuss safety and health issues with the goal of improving the program.
(all of them apply)
In class we discussed five non-destructive testing methods used to identify problems on pressure vessels. Give me any two of the five.
- Magnetic testing - Liquid Gap testing
On a guardrail system what are the minimum heights for the: - Toprail ____ inches +/- ____ inches - Midrail ____ inches - Toeboard ____ inches with a maximum gap to the floor of one-quarter inch
- Toprail __42__ inches +/- __3__ inches - Midrail __21__ inches - Toeboard __3 1/2__ inches with a maximum gap to the floor of one-quarter inch
Employers must report the following to OSHA a. Loss of Eye b. Amputation of a fingertip c. Hospitalization d. Deaths
-Loss of Eye -Amputation of a fingertip -Hospitalization -Deaths (All of the above)
The work rest on a grinder mist be kept CLOSELY ADJUSTED, max gap = ___" to prevent work from jamming & breaking wheel
1/8"
what are the four parts to the creation of a fire?
Heat, Oxygen, Fuel, Chain rxn
Limitations of Presence Sensing Devices as machine guards include: a. Does not protect against mechanical failure b. May require frequent alignment calibration c. Excessive vibration may cause lamp filament damage and premature burnout d. ____________________________________________________________
If it does not shut off, its automatic
Who is responsible to conduct most of OSHA's research?
NIOSH
The following must be in place maintained and legible: Nameplates Tires Seatbelts Steering wheel
Nameplates
_______ persons are those permitted to work on or near exposed energized parts and shall, at a minimum, be trained in and familiar with the following: a. The skills and techniques necessary to distinguish exposed live parts form other parts of electric equipment b. The skills and techniques necessary to determine the nominal voltage of exposed live parts
authorized
When guardrail systems are used around holes that serve as points of access (such as ladderways), the guardrail system opening must have a self-closing gate that slides or swings ______ from the hole.
away
The minimum height is ____ as measured from the leading edge of the stair tread to the top surface of the handrail a. 27 inches b. 30 inches c. 36 inches d. 39 inches
b. 30 inches
General Industry employers have a duty to protect workers from falling at what minimum height? a. 6 feet b. 4 feet c. 15 feet d. any height
b. 4 feet
A safety can used to store flammable liquids can be no larger than _________ gallons. a. 55 b. 5 c. 1 d. 10
b. 5
When considering hearing protection, the rating you should refer to is the ___. This will tell you how much attenuation the hearing protection provides. a. OCS b. NRR c. NEP d. EPA
b. NRR
Exit routes are a ________ and unobstructed path of travel from any point within a workplace to a place of safety.
continuous
This standard (lock-out tag-out) does not apply to work on cord and plug connected electric equipment if the plug is under the exclusive _______ of the employee performing the servicing or maintenance
control
A confined space is one that a. Has a means of entry or exit b. Large enough size for employee entry c. Not designed for continuous human occupancy d. All of the above
d. All of the above
A permit-required confined space has at least one of the following: a. Hazardous atmosphere b. Contains a material having a potential to engulf c. Not designed for human occupancy d. All of the above
d. All of the above
Following the application of the lockout devices to energy isolation devices, all potentially hazardous stored or residual energy shall be: a. Relieved b. Disconnected c. Restrained d. All of the above
d. All of the above
Overhead cranes must be inspected a. Initially b. Frequently c. Periodically d. All of the above
d. All of the above
The OSH Act covers all except which of the following? a. Manufacturing b. Construction c. Longshoring d. Mining
d. Mining
When mechanical handling equipment is used sufficient safe clearances must be allowed at all of the following except: a. Loading docks b. Doorways c. Turns d. Parking lots
d. Parking lots
The following are examples of servicing and/or maintenance workplace activities except: a. Installing b. Adjusting c. Inspecting d. Use
d. Use
Examples of compressed gases include: a. liquefied b. non-liquefied c. dissolved gases d. all of the above
d. all of the above
What are the two signal words?
danger, warning
Surge protectors protect the _____ whereas, GFCIs protect the _____
equipment, employee
If a cryogenic liquid comes into contact with a worker's skin it _____________ the skin?
freezes
A barrier that prevents exposure to the hazard is a _______
guard
Skin corrosion or irritation, aspiration hazard, serious eye damage or eye irritation, or respiratory or skin sensitization are all examples of _________ hazards.
health
Suitability of equipment may be evidenced by _____ and _____
listing and labeling
The following are benefits of safety and health programs except: a. Improved employee morale b. Higher productivity c. Lower workers' compensation costs d. Loss of good will
loss of good will
(Use the same word to complete this paragraph) For a pressure vessel to function properly, it requires regular __________. You should have a proper __________ program of the entire pressure system, which checks the age of the vessel. One thing you should keep your eye on is the sign of problems. If a safety valve is discharging rapidly, then it is either a sign of a faulty safety valve or over pressurizing system. Besides this, you should also check for any signs of wear or corrosion.
maintenance
______ production operations are not covered by the standard (lock-out tag-out)
normal
A ____________ hazard is a chemical that is classified as posing one of the following hazardous effects: explosive, flammable (gases, aerosols, liquids, or solids), oxidizer (liquid, solid or gases), self-reactive, pyrophoric (liquid or solid), self-heating, organic peroxide, corrosive to metal, gas under pressure, or in contact with water emits flammable gas.
physical
The area on a machine where material is positioned for processing or where work is actually being performed on the material is known as the _______________
point of operation
A _____________ statement describes recommended measures that should be taken to minimize or prevent adverse effects resulting from exposure to a hazardous chemical, or improper storage or handling.
precautionary
______ ______ are large containers that are used to hold gases or liquids at high temperatures. The contents of pressure vessels are at a substantially different pressure than the ambient pressure.
pressure vessels
The figure below is an example of what type of machine guarding device? __________ (picture on phone)
pullback
E-stops are usually conveniently located, who really needs to be able to hit an E-stop?
the bystander
The employers must ensure each cover for a hole in a walking-working surface is capable of supporting at least _____ the maximum load that may be imposed on the cover at any one time
twice
The final step in the lockout procedure is to ______ the energy isolation
verify
All employers must prepare a _________________ hazard communication program.
written
Describe the hazard in the photo on your phone
you should not step on either of the top two platforms of the ladder