SAFETY 111 FINAL

The minimum breaking strength for anchorages used in vertical lifelines two workers is _____ pounds for EACH person attached

5000

A worker on a low slope roof can work in the designated area which is not less than ___ feet from the roof edge

6

There are many situations that may cause slips, trips, and falls, for instance (select all that apply) a. Grease b. Oil c. Water d. Improper Footwear

(All apply)

Rescue procedures must be practiced once every __ months

12

A floor hole is an opening measuring less than ___ inches but more than ___ inch(es) in its least dimension, in any floor, platform, pavement, or yard, through which materials but not persons may fall.

12, 1

How long must an eyewash be able to flush a worker's eyes? 5 minutes 10 minutes 15 minutes 1 minute

15 minutes

How many parts are in an SDS?

16

What other OSHA standard specifies the eye wash? 1910.151 1910.1200 1910.132 1910.106

1910.151

Which is an example of a vertical standard?

1910.261 (Pulp, Paper, and Paperboard Mills)

A powered industrial truck is unattended when the attendant is how far from the truck? 10 feet 20 feet 15 feet 25 feet

25 feet

What is the minimum width of an exit route?

28 inches

A minimum working space around electrical panels is ___ feet

3

When using a ladder how many feet must extend above the landing point?

3

Every flight of stairs with ___ or more risers must have standard stair railings on all open sides (or standard handrails if the stairs are enclosed)

4

Every open-sided platform or wall that is ___ feet or more above the next level must be protected by a standard railing.

4

Point of operation hazard -- OSHAs enforcement policy (CPL 2-1.25) Guidelines for point of operation guarding for power press brakes. For the purpose of maintaining a "safe distance" as discussed in this instruction, the operating employee and helping employee(s) must not approach closer than necessary and in no case, closer than __ inches to the power press brake point of operation.

4

Periodic inspections of cranes may identify the following (more than one may apply): a. Deformed, cracked, or corroded members b. Loose bolts or rivets c. Cracked or worn sheaves and drums d. Worn, cracked or distorted parts (e.g. pins)

All apply

Batter charging facilities must provide for: Eye wash Fire extinguisher Protection from damage Adequate ventilation All of the above

All of the above

When using a scaffold you should never: a. Climb the bracing b. Climb the frame c. Carry tools d. All of the above

All of the above

A class __ hardhat is designed for protection against high-voltage

E

At a minimum, how often must a PIT driver be reevaluated? Every 6 months Annually Every 3 years As needed

Every 3 years

True or False: All fall protection connectors must be drop forged, formed steel or high pressure welded, and be corrosion resistant

False

True or False: Body belts are an acceptable part of a personal fall arrest system

False

True or False: Employers must have and maintain an audible employee alarm system?

False

True or False: Fire extinguishers must be within 50 feet of any combustible area.

False

True or False: The OSH Act was signed into law by President Richard Nixon on December 29, 1969

False

True or False: Each affected employee shall affix a personal lockout or tagout device to the group lockout device, group lockbox, or comparable mechanism when he or she begins work, and shall remove those devices when he or she stops working on the machine or equipment being serviced or maintained

False (each "authorized" employee)

While any employee is exposed to contact with parts of fixed electric equipment or circuits which have be de-energized, the circuits energizing the parts shall be _______ ____ or tagged or both

Locked out

What OSHA Outreach Program is a great source of help for small business?

OSHA Onsite Consultation Program

High lift trucks must be fitted with the following: Overhead guard Rollerover protection Stabilizers Hard hats

Overhead guard

Each disconnecting means must be legibly marked to indicate its _____

Purpose

What does the first S in PASS stand for?

Squeeze

______ and circuit breakers must be legibly marked

Switches

What are the maximum allowable lateral forces in a guardrail system? Toprail ____ pounds Midrail ____ pounds Toaeboard ____ pounds

Toprail __200__ pounds Midrail __150__ pounds Toeboard __50__ pounds

True or False: A general duty of the employers under the OSH Act is to furnish each of his employment and a place of employment which are free of recognized hazards that are likely to cause serious physical harm to his employees?

True

True or False: A general requirement for electrical safety is that illumination must be provided for all working spaces about service equipment

True

True or False: A workplace is permitted to have only one means of exit?

True

True or False: Company leadership must make safety and health a core value and lead by example.

True

True or False: Compressed gas cylinders must be secured to prevent them from falling over

True

True or False: Currently, OSHA's lock-out tag-out standard covers servicing and maintenance of machines and equipment in which the "unexpected" energization or start up of the machines or equipment, or release of stored energy could cause injury to employees

True

True or False: Effective communication and coordination raises awareness of contractors and staffing agencies to the hazards

True

True or False: Electrical equipment may not be used unless it is suitably marked

True

True or False: Employees should be given opportunities to participate in program design and implementation

True

True or False: Employers must develop plans with measures to protect workers during emergencies and non-routine activities

True

True or False: Employers must know all of their potential ignition sources and how to control them.

True

True or False: Other workers are never allowed to ride on the front tines of the forklift

True

True or False: Regardless of height, if a worker can fall into or onto dangerous machines or equipment, employers must provide guardrails and toeboards.

True

True or False: Storage of material must be such that the material does not create a hazard

True

True or False: The route to an exit must be clearly indentified.

True

True or False: When a truck is left unattended the load must be fully lowered, controls neutralized, power shall be shut off, and brakes set

True

True or False: You should always inspect a ladder before use.

True

True or False: You should always keep 3 points of contact with a ladder.

True

True or False: the on-site employer shall ensure that his/her employees understand and comply with restrictions and prohibitions of the outside employer's energy control program

True

True or False: Vertical Standards are specific to only a particular industry?

True, horizontal standard affects everyone equally

Employees have a right to each of the following except:

Workers may not file a complaint directly with OSHA

The following are elements of the PIT training except: Computer learning Practical exercises Evaluation Written test

Written test

Yes or No: An employer with ten employees discusses her emergency action and fire prevention plan with her employees over pizza at lunch. Is she in compliance with OSHA requirements?

Yes

When inspecting the workplace, you notice some workers wearing glasses. What designation should be on the eyewear?

Z87

Number the four levels of the hierarchy of controls listed below from most effective (1) to least effective (4): ____ Engineering controls ____ Personal Protective Equipment ____ Elimination/Substitution ____ Administration Controls

__2__ Engineering controls __4__ Personal Protective Equipment __1__ Elimination/Substitution __3__ Administration Controls

Guards are barriers which prevent access to danger areas, there are four types, match them: (photo on phone) ____ Adjustable guards ____ Interlocked Guards ____ Fixed guards ____ Self-adjusting guards

__B__ Adjustable guards __C__ Interlocked Guards __A__ Fixed guards __D__ Self-adjusting guards

As discussed in class, a significant cause of degradation of synthetic slings is from a. Acids b. Age c. Oxidation d. Cutting

a. Acids

What is the order in which sampling is performed w conducting air monitoring to assess air quality in a Permit-required space a. Oxygen, flammable, toxic b. Toxic, flammable, oxygen c. Flammable, toxic, oxygen d. Toxic, oxygen, flammable e. Flammable, oxygen, toxic

a. Oxygen, flammable, toxic

List four of the six major elements of an effective safety and health program

a. Training b. Identify hazards c. Leadership Management d. Communication

In mechanical power presses there are two types of clutches. a. _____ - revolution one that cannot be disengaged until one complete stroke is made b. _____ - revolution can disengage clutch at any point along the cycle

a. full b. part

The distance between the periphery and the adjustable tongue guard on a pedestal grinder shall never exceed ________ inch a. one-quarter b. one-half c. one-eighth d. one e. none of the above

a. one quarter

Employers must keep Safety Data Sheets readily _____________________ to workers.

accessible

A person whose job requires him/her to work in an area in which such servicing of maintenance is being performed is known as ___________________

affected employee

The two basic types of respirators are ___-purifying and ______-supplying

air, atmosphere

Flexible cords and cables shall be _______ and suitable for conditions of use and location

approved

Two types of hazards for which a permit is required are ________ and __________

atmospheric, non-atmospheric

Currently, OSHA may penalize an employer how much for one serious violation?

$12,934

An energy isolating device is/are which of the following? (more than one can apply) a. A manually operated electrical circuit breaker b. A disconnect switch c. A manually operated switch by which the conductors of a circuit can be disconnected from all ungrounded supply conductors and, d. a line valve; a block; and any similar device used to block or isolate energy

(all apply)

A few things that can be done to start a safety and health program include (circle all that apply): a. Train workers on how to identify and control hazards b. Inspect the workplace with workers c. Assign workers the task of choosing, implementing, and evaluating their solutions d. Discuss safety and health issues with the goal of improving the program.

(all of them apply)

In class we discussed five non-destructive testing methods used to identify problems on pressure vessels. Give me any two of the five.

- Magnetic testing - Liquid Gap testing

On a guardrail system what are the minimum heights for the: - Toprail ____ inches +/- ____ inches - Midrail ____ inches - Toeboard ____ inches with a maximum gap to the floor of one-quarter inch

- Toprail __42__ inches +/- __3__ inches - Midrail __21__ inches - Toeboard __3 1/2__ inches with a maximum gap to the floor of one-quarter inch

Employers must report the following to OSHA a. Loss of Eye b. Amputation of a fingertip c. Hospitalization d. Deaths

-Loss of Eye -Amputation of a fingertip -Hospitalization -Deaths (All of the above)

The work rest on a grinder mist be kept CLOSELY ADJUSTED, max gap = ___" to prevent work from jamming & breaking wheel

1/8"

what are the four parts to the creation of a fire?

Heat, Oxygen, Fuel, Chain rxn

Limitations of Presence Sensing Devices as machine guards include: a. Does not protect against mechanical failure b. May require frequent alignment calibration c. Excessive vibration may cause lamp filament damage and premature burnout d. ____________________________________________________________

If it does not shut off, its automatic

Who is responsible to conduct most of OSHA's research?

NIOSH

The following must be in place maintained and legible: Nameplates Tires Seatbelts Steering wheel

Nameplates

_______ persons are those permitted to work on or near exposed energized parts and shall, at a minimum, be trained in and familiar with the following: a. The skills and techniques necessary to distinguish exposed live parts form other parts of electric equipment b. The skills and techniques necessary to determine the nominal voltage of exposed live parts

authorized

When guardrail systems are used around holes that serve as points of access (such as ladderways), the guardrail system opening must have a self-closing gate that slides or swings ______ from the hole.

away

The minimum height is ____ as measured from the leading edge of the stair tread to the top surface of the handrail a. 27 inches b. 30 inches c. 36 inches d. 39 inches

b. 30 inches

General Industry employers have a duty to protect workers from falling at what minimum height? a. 6 feet b. 4 feet c. 15 feet d. any height

b. 4 feet

A safety can used to store flammable liquids can be no larger than _________ gallons. a. 55 b. 5 c. 1 d. 10

b. 5

When considering hearing protection, the rating you should refer to is the ___. This will tell you how much attenuation the hearing protection provides. a. OCS b. NRR c. NEP d. EPA

b. NRR

Exit routes are a ________ and unobstructed path of travel from any point within a workplace to a place of safety.

continuous

This standard (lock-out tag-out) does not apply to work on cord and plug connected electric equipment if the plug is under the exclusive _______ of the employee performing the servicing or maintenance

control

A confined space is one that a. Has a means of entry or exit b. Large enough size for employee entry c. Not designed for continuous human occupancy d. All of the above

d. All of the above

A permit-required confined space has at least one of the following: a. Hazardous atmosphere b. Contains a material having a potential to engulf c. Not designed for human occupancy d. All of the above

d. All of the above

Following the application of the lockout devices to energy isolation devices, all potentially hazardous stored or residual energy shall be: a. Relieved b. Disconnected c. Restrained d. All of the above

d. All of the above

Overhead cranes must be inspected a. Initially b. Frequently c. Periodically d. All of the above

d. All of the above

The OSH Act covers all except which of the following? a. Manufacturing b. Construction c. Longshoring d. Mining

d. Mining

When mechanical handling equipment is used sufficient safe clearances must be allowed at all of the following except: a. Loading docks b. Doorways c. Turns d. Parking lots

d. Parking lots

The following are examples of servicing and/or maintenance workplace activities except: a. Installing b. Adjusting c. Inspecting d. Use

d. Use

Examples of compressed gases include: a. liquefied b. non-liquefied c. dissolved gases d. all of the above

d. all of the above

What are the two signal words?

danger, warning

Surge protectors protect the _____ whereas, GFCIs protect the _____

equipment, employee

If a cryogenic liquid comes into contact with a worker's skin it _____________ the skin?

freezes

A barrier that prevents exposure to the hazard is a _______

guard

Skin corrosion or irritation, aspiration hazard, serious eye damage or eye irritation, or respiratory or skin sensitization are all examples of _________ hazards.

health

Suitability of equipment may be evidenced by _____ and _____

listing and labeling

The following are benefits of safety and health programs except: a. Improved employee morale b. Higher productivity c. Lower workers' compensation costs d. Loss of good will

loss of good will

(Use the same word to complete this paragraph) For a pressure vessel to function properly, it requires regular __________. You should have a proper __________ program of the entire pressure system, which checks the age of the vessel. One thing you should keep your eye on is the sign of problems. If a safety valve is discharging rapidly, then it is either a sign of a faulty safety valve or over pressurizing system. Besides this, you should also check for any signs of wear or corrosion.

maintenance

______ production operations are not covered by the standard (lock-out tag-out)

normal

A ____________ hazard is a chemical that is classified as posing one of the following hazardous effects: explosive, flammable (gases, aerosols, liquids, or solids), oxidizer (liquid, solid or gases), self-reactive, pyrophoric (liquid or solid), self-heating, organic peroxide, corrosive to metal, gas under pressure, or in contact with water emits flammable gas.

physical

The area on a machine where material is positioned for processing or where work is actually being performed on the material is known as the _______________

point of operation

A _____________ statement describes recommended measures that should be taken to minimize or prevent adverse effects resulting from exposure to a hazardous chemical, or improper storage or handling.

precautionary

______ ______ are large containers that are used to hold gases or liquids at high temperatures. The contents of pressure vessels are at a substantially different pressure than the ambient pressure.

pressure vessels

The figure below is an example of what type of machine guarding device? __________ (picture on phone)

pullback

E-stops are usually conveniently located, who really needs to be able to hit an E-stop?

the bystander

The employers must ensure each cover for a hole in a walking-working surface is capable of supporting at least _____ the maximum load that may be imposed on the cover at any one time

twice

The final step in the lockout procedure is to ______ the energy isolation

verify

All employers must prepare a _________________ hazard communication program.

written

Describe the hazard in the photo on your phone

you should not step on either of the top two platforms of the ladder