Shop Safety Test - Ag

Before one plugs in the drill motor, it should be

Checked if the switch is off

Sharp or pointed tools or materials should not be carried in the clothing; hold sharp points or edges _____________.

Down

Eye glasses must never be substituted for face shields or __________________.

Goggles

When using the grinder/sander, it is better to

Make light passes; don't force it

A three-wire ground plug on a drill is

Necessary for short circuit protection

Chips, shavings and scraps are cleaned from benches and work surfaces with ____________.

a brush

Safe eye protection for arc welding is

a welding hood with properly tinted lens

One must keep ______________ away from revolving spindle, chuck drill and chips.

all

Your hands should be as free as possible of __________.

all

Because of the unusual danger involved when using the grinder/sander, you should

all of the above

Files are very hard and brittle. You should avoid striking against them or using them as a _________________.

all of the above

One should be sure and turn the power off after using the grinder and keep all __________________ away from the grinder.

all of the above

What must be arranged so that it will not me caught in the drill press?

all of the above

When hammering on machined, tempered or hardened surfaces, you should use a soft-faced hammer, such as _____________.

all of the above

You should never use ______________ on a screwdriver to increase the torque on the screw.

all of the above

You should use a screwdriver with ______________ handle when working around electrical equipment.

an insulated

When drilling with a portable electric drill, one should

apply firm, steady pressure

One should set the grinder tool rest ________________.

as close as possible without touching the wheel

When carrying a long piece of stock, the student should ask another student to______________

assist in carrying the stock

A cracked or broken wheel should always be reported to the teacher ____________________.

at once

If work comes loose and is seized by the drill, one should __________________.

attempt to turn off the power

Fingers should be kept _________ the blade when in operation.

away from

Fingers should be kept __________ moving belt or disc.

away from

Before starting a new welding project, it must

be inspected/approved by the teacher

The chuck key must be removed

before power is turned on

You should select the right type of hacksaw ___________ for the type of material to be cut.

blade

Vise handles and control knobs are to be tightened ____________________.

by hand

Smaller pieces to be ground or sanded should be

clamped or secured in a vise

The table should be kept as ________ as possible to the belt or disc.

close

One should always keep the hands _____________ the grinding wheel.

close to

Oily rags and waste must be put in a ____________

closed metal container

What should you do as the drill begins to break through the work?

ease up on the feed pressure

As the drill bit breaks through the material, one should

ease up on the pressure

When completing a cut with a saw, one must ___________________.

ease up pressure on the saw

One should only use the ______________ of the wheel for grinding.

face

One should hold the work so it will not be pulled out of or pushed into one's ______________.

feet

All material used on the grinder needs to be held ______________ the tool rest.

firmly against

Do not grind in a crowded area, there is danger of

flying particles or fractured disc

Long pieces of stock should be on the ____________ side of the column.

front

Because of the extreme hazards of high-speed particles from the abrasive wheel, you must wear

goggles or a face mask

One should check with the instructor to determine if correct _________ is being used for the material being sanded.

grit

You should only use chisels and punches that are in good condition. Keep the cutting edges _____________.

ground sharp

You should never use a hacksaw as a ____________ to knock off a piece of material that has been partially cut.

hammer

Files should be kept clean and have a tight fitting _____________________.

handle

Serious injury to the eyes or skin may be caused by exposure to the arc, due to the

harmful rays the arc emits

Before using a hammer, one should check the ____________.

head and handle for damage

No one should ever allow

his/her eyes to be exposed to the arc

When holding the portable electric drill, one should

hold firmly and keep both hands away from the chuck

When using a chisel, one should __________________.

hold the work with a vise or clamp

You should stand to one side of the grinder as it gathers speed because ______________________.

if it has a defect in the wheel, it may fly apart

Upon entering another lab/class, a student shall report to the teacher _________________.

immediately

When one uses a screwdriver on a small object, the object should be held _________________.

in a vise

One should never make adjustments to the drill press while it _______________.

in motion

Take care regarding the power cord when using the grinder/sander because

it may be entangled in the spinning disc

Before turning on the drill press, one must make sure that the ____________ is not in the chuck.

key

One must apply a ______ pressure against the belt or disc.

light

As with all other portable power tools, you must

make sure the machine is grounded

Before using a chisel, punch or drift, one should check to see that the head is__________________.

not mushroomed

If the switch does not function as designed, one should

notify the instructor immediately

Arc welding must be done

only in approved, screened areas

Gasoline, paint, kerosene and other flammable materials are never to be used near _____________.

open flames

You should not grind aluminum, brass, copper or _______________ on the grinder.

plastic

You should inspect the hacksaw frame to see that the blade is ______________ installed.

properly

One must wear a face shield, safety glasses or goggles when using the grinder because these ___________________.

protect the eyes from flying particles

For protection against ultraviolet rays, infrared rays, flying sparks and heat, the welder must wear

protective clothing and a welding helmet

To grind small pieces of stock, one must _____________.

receive special permission and insturction

Once you have checked the condition of the cord, sanding disc or grinding wheel and you fine something defective, you should

report it to the instructor

One should consult with the instructor before attempting to _________ the edge of thin gauge material.

sand

The protection of everyone in the shop from injury by sparks and flashes while arc welding is the responsibility of the

school

All work must be carefully ________________ on the drill press so that personal injury and damage are avoided.

secured

One should clamp material in the vise

securely

If a wrench is too small, it is best to __________.

select the proper size for the job

Before using a drill bit, you should make sure that the bit is _________________.

sharp

Before using drill bits, you should check for ______________?

sharpness

If the operator leaves the welding job, he/she must

shut off the machine

The larger the bit, the __________ the speed of the drill press.

slower

When the electrode holder is not in use, it should be placed only on the

special hanger in the booth

Adjustments are made only when the machine is

stopped

You should never apply a wrench to _____________ machinery.

stopped

Electric drills must not be used when wet or around wet areas because of

the danger of being shocked

One should brush chips or cuttings from the drill press table only when ________________.

the power is off

As soon as the hole is drilled, one should back the drill out of the hole with _________________.

the power on

In case of injury, a student should report at once to ________________.

the teacher

Before beginning an operation, one should make certain that all angle clamps are

tight

Screwdrivers are designed to _________________.

to drive screws

You are required to keep _____________ from projecting over the edges of tables and work-surfaces.

tools and materials

When using adjustable (crescent) wrenches, you should pull _________________.

toward the movable jaw

If the drill catches on a piece of work and spins it, one should ______________________.

turn off the power

One should make all guide adjustments where required before the power is

turned on

One must always check the belt or disc on the sander to determine the amount of wear before

turning on the power

One should make all adjustments on the machine before

turning on the power

Use the proper _____________ hammer for the job at hand.

type and size

The switch and switch locking features should be

understood and used as instructed

If the drill motor sparks, smokes or makes unusual noises, one should

unplug the drill and report it to the teacher immediately

When using the chipping hammer, the operator is required to

wear clear goggles or face shield

Goggles or face shield should be worn

when cutting anything

When drilling thin material, one should back up the material with ___________ and clamp it firmly.

wood

A drill and bit should be assembled at the _____________.

work station