Woodshop Test

1/32

1/8 inch clockwise turn of the elevation wheel on the planer removes ____ of an inch of wood. this is the perfect amount to remove each pass especially with hardwoods. when you remove too much material to quickly, the surface will have blemishes and planer marks. it is better to remove less and by doing this it greatly enhance your thickness accuracy

cutting to fast, board is moving, board not completely pushed back on fence, board is warped

4 main safety concerns for kickback or binding on the miter saw

splitter not being used, edge against fence is not jointed, board not pushed all the way past blade, board is warped, fence is not locked

5 main safety concerns for kickback or binding on table saw

4 inches

MAINTAIN A ______ MARGIN OF SAFETY ON THE BANDSAW

fence

NEVER CUT STOCK FREEHAND. use the _____ as a rip guide

reliefcuts

a few well-placed _______ openings will give you sufficient turning room to make tight cuts on the bandsaw. sometimes, corner holes are used just to make band saw cutting easier.

1/2 inch

adjust the blade guard assembly so it is no more than _____ above your work on the bandsaw. (about the thickness of your thumb)

complete stop

after making a cut, but before raising the saw blade on the miter saw make sure that the blade has come to a ____

7 inches

all wood scrap goes in the fire pit bin, not the scrap bin unless it's over _____ long

speed

allow the bandsaw to reach full ____ before starting to feed the work

lower

always ________ the guard to the surface of your stock on the bandsaw so work does not bounce or break while cutting

tighten, tension, test, breakage

always _________ the blade in, then properly ________ the arm, then ______ the tension before starting. doing this in the wrong order is the most common cause for blade ________ on the bandsaw and donut parties

cracked, damaged

always inspect the router before each use of the router and never use a bit if the carbide is ______ or ______ in any way

clamped

always make sure your smaller work is _______ on the drill press

grain, through

always plane with the ______ never against it. the grain direction should be pointed _____ the planer mouth

chuck key

always tighten the drill bit with a ______ before using the drill press

done

clean the siding table saw machine and work area when you are _______

large

crosscut _____ of plywood on the sliding table saw. do not use the traditional table saw for crosscutting full plywood sheets!

front, back

crosscut narrow stock on the ______ side of the fence and wide stock on the _____ side of the fence

table saw

crosscutting on the ______ is dangerous. cross cuts should be made on the grizzly sliding table saw

drop

do not ____ plywood on the sliding table saw table; this might throw the machine out of alignment

cut to fast

do not _______ move slow and steady on the scroll saw

end

do not joint _____ grains on the jointer

fingers

do not place ________ near the blade while cutting or removing scraps, use a scrap piece of wood for that on the bandsaw

adjust

do not remove the quard. do not _____ the jointer without shop teachers permission

teeth, remove

feed the bandsaw only as fast as the _____ will ____ the wood easily

with

feed the work so that the knives will cut "_____ the grain" on the jointer (only use new stock that is free of knots , splits and checks)

firmly, fence

hold stock ____ on the table and against the ____ so it does not shift or kick out when using the miter saw

unstable

holding the work piece by hand is _____ and may lead to loss of control. use push sticks

blade

if the ______ breaks on the bandsaw, turn off the machine and notify the instructor

teacher, back

if you ever need to remove the splitter or the guard on the table saw to make a cut, you must get the _____ to help, when you complete the cut put the splitter ___ in place

clicking

if you hear a ______ noise, turn off the machine at once. this sound indicates a crack in the blade. if the blade breaks, shut off the power and move away from the machine until both wheels stop

stop

if your work comes loose on the drill press, _____ the machine and step back to allow the machine to come to a complete stop

best

joint the _____ edge on your board

sharp

jointer knives must be _____. dull knives will vibrate the stock and may cause a kickback

proper

keep the blade guard in the ______ position at all times

guard

keep your hands away from the cutter head, even though the ______ is in position on the jointer

4 inches

maintain a _____ margin of safety from the blade, This means that you must keep your hands _______ away from the saw blade.

4 inches

maintain a _____ margin of safety on the table saw. a variety of pushsticks are provided and must be used when cutting closer than ______

4 inches

maintain at least a ____ margin of safety. this means that your hands should always be at least _____ from the cutter head at all times

plugging

make sure router is turned off before ______ it in

secure and tight

make sure the blade is ________ before cutting on the scroll saw

nails and knots

make sure the work surface is free from ______- and other foreign objects

twist, break

make turns carefully on the bandsaw and do not cut a radius so small that the blade _____ or ________

3/8

material cannot be less than ______ thick on the jointer

1/16th inch

maximum cut depth for jointing an edge is _____

thick, 3/8

most boards are too ________ to use on the scroll saw blades. our lumber has to be _______ of an inch thick or less to cut. lumber that is thicker than that will break the blades

under

never move your hands _____ the blade, whether it is moving or not on the miter saw

hand

never try to stop the spindle on the drill press by _____ turn off the machine and step back wile the machine comes to a complete stop

backing

plan cuts before using the bandsaw to avoid _____ out of cuts/curves whenever possible. stop the machine before backing out of a long curved cut

parallel

planer makes two faces ______

scrap, chipping out

put a _____ board underneath your work if you are trying to prevent ______ on the bottom side of your work during the drill press

scrapwood

remove wood scrap from the band saw with a piece of _______

2nd, parallel

rip ______ side on your board ______ to the jointed edge

jointed

rough stock must have at least one edge _______ before being cut on the table saw

jointer

second step in squaring a board

parallel

sliding table saw makes board ends ______

reach, behind

stand to the left side of the blade on the table saw. do not ____ across it or stand _____ the blade due to kickback

planer

step 4 in squaring a board

sliding table saw

step 5 in squaring a board

miter saw

step one in squaring a board

7 inches, 3/8th inch

stock must be at least _____ long to pass through and at least _____ inches thick on the jointer

tailoff

students helping to ______ stock from the table saw should not push or pull the stock. they should support the boards as necessary. the operator must control the speed and direction of the cut

helper

support large sheets of plywood properly; you might need a _____ for this

ripping wood to exact width

table saw is used for _________

lathe

the accuracy stop that is used on the sliding table saw for mass production needs to be put on the _____ bench when not in use, not the floor

4 inches

the margin of safety on the sliding table saw is ______. never reach your fingers in close to the blade to remove scrap or even to remove your project

cross

the miter saw will only be used for a type of cut called ______

surfacing

the planer is used for ______ the faces of lumber to create a desired thickness

7

the shortest length board you may push through the table saw is ____ inches

width, 15 inches, 13 inches

the size of a planer is determined by the length of its _________. our heavy duty planer is ______ while the smaller planer is _______

crosscutting

the sliding table saw is used for ______ plywood as well as cross cutting solid lumber

10 inches, 7 inches

the smallest length board you may push through the large planer is ______ and at least _____ long on the small planer. these numbers will be labeled on each machine

3/4

the smallest length board you may push through the table saw is ______ inches

towards

the table saw blade spins _____ you; this allows you to control the cut

blade guard, important

the table saw is equipped with a _______. this device is the most ____ safety feature for this machine and may not be removed

table saw

third step in squaring a board

drill press

this is usually done after your board has been dimensioned

drill press

tuck in loose clothing, tie back long hair, roll up sleeves and wear safety glasses on the _____

fire

turn off the machine as soon as you finish working on the bandsaw. all scraps must be taken to the ____ bin

pushstick

use a ______ with smaller stock to protect your fingers on the table saw

knives

use a push stick when jointing a flat surface or a board that is less than 4 inches high. never apply pressure direction over the _____ with your hand

drill press

used for boring holes as well as predrilling for screws

sliding table saw

used for crosscutting big sheets of plywood and smaller solid wood to exact length (crosscutting)

miter saw

used for crosscutting wood to rough or exact length (1/8th inches long)

Jointer

used for jointing and edging wood

planer

used for thinning wood to a desired thickness

scroll saw

used to cut intricate curves and joints

bandsaw

used to cut out irregular shapes either cross the grain or with the grain

router/router table

used to put decorative edges on your boards

severe pinching

watch your fingers on the back of each board as you push it through the planer due to _________

safety glasses

wear ______

guard

wheel guard door must be closed and the blade ______ must be properly adjusted before turning on the bandsaw

left side

when boring a hole through the board, make sure the long end of the board is off to the ______ of the drill press. doing this will ensure that if you have spin out, your work piece will come into contact with the column, instead of your body

clamp

when crosscutting larger panels of plywood on the sliding table saw, use our orange _____ to keep your panel tight to the fence

greater

when crosscutting stock on sliding table saw, make sure the amount of lumber on the sliding fence is _______ than the length of cut

wrist touches, kickback

when using the table saw make sure that your lumber is pushed past the blade and that your _____ the black guard pole before removing your pushstick. this means the board is past the blade and has no chance of _____

1/2 inch

when using the table saw set the blade so that it extends no more than ____ above the stock to be cute

zero

when you complete your operation on the table saw, clear the saw of dust and wood scrap. return the saw blade to the ____ setting

machine, work area

you must clean the ______ and ______ when done with jointer