Exam Prep 1

15. Cost Estimate and Job Cost system are the most _______ ways to keep an eye on monies going in and out. a. Efficient b. Expensive c. Hardest d. Useless

A ... Explanation: Cost Estimate and Job Cost system are the most efficient ways to keep an eye on monies going in and out. Ref-Business Law and Project Management Page 8-9

25. _____is the remaining time after a task is complete and before the next task begins. a. Float time b. Free time c. Both A and B d. None of the above

A ... Explanation: Float Time is the remaining time after a task is complete and before the next task begins. Ref-Business Law and Project Management Page 8-2

37. A company ________ to pay overtime to executives or administrative employees. a. Is not required b. Is required c. Can decide d. None of the above

A...Explanation: A company is not required to pay overtime to salaried or commissioned employees. Ref-Business Law and Project Management Page 10-4

67. Calculate how many square feet will 2 squares of asphalt shingles cover? a. 200 square feet b. 100 square feet c. 400 square feet d. 188 square feet

A...Explanation: A roofing square is the amount of roofing material needed to provide 100 square feet of finished roof surface. 2 squares x100 sq. ft./square = 2 x 100 sq. ft. = 200 sq. ft.

12. A _____ is similar to the design/build contract, however it also contains the duties of attaining the funds and property associated with the project. a. Turnkey b. Build c. Design d. None of the above

A...Explanation: A turnkey agreement is a contract for the construction, installation, etc. whereby the contractor assumes total responsibility from design through completion of the project. The project is ready to produce cash flow upon completion. Ref-Business Law and Project Management Page 7-6

55. Which of the following buildings would be classified as an A-2 occupancy? a. Restaurants b. Libraries c. Arenas d. Theatres

A...Explanation: Assembly uses intended for food and/or drink consumption including, but not limited to: Banquet halls, Casinos (gaming areas), Nightclubs, Restaurants, cafeterias, and similar dining facilities (including associated commercial kitchens), Taverns and bars. Ref-2015 IBC 303.3

35. An OSHA approved spreader bar must be how long when lifting materials 30 foot or longer? a. At least one-half the length of the reinforcing bars b. At least two-times length of the reinforcing bars c. At least three-times the length of the reinforcing bars d. At least four-times the length of the reinforcing bars

A...Explanation: At least one-half the length of the reinforcing bars. Ref-Placing Reinforcing Bars Page 8-5

53. During construction barriers shall be not less than _____ in height and shall be placed on the side of the walkway nearest the construction. a. 8 feet b. 10 feet c. 12 feet d. 15 feet

A...Explanation: Barriers shall be not less than 8 feet (2438 mm) in height and shall be placed on the side of the walkway nearest the construction. Ref-2015 IBC 3306.5

3. Calculate how many board feet is required if you need 10-inch wide, 3/4 board that measures 96-inches in length for your project? a. 5bf b. 6bf c. 7bf d. 10bf

A...Explanation: Board feet is the measurement of the volume of wood needed for a project. One board foot equals 144 cubic inches. It is calculated by multiplying thickness by width by length and then dividing the total by 144. So you would multiply 96 by 10 by .75 for a total of 720. Then, you divide 720 by 144 for a total of 5bf.

24. Which of the following estimate considerations will not increase the cost of a project? a. Increased availability of labor b. Increased square footage c. Increased inflation d. Increased quality expectations

A...Explanation: Building project price is affected by the size of the project, the quality of the project, the location, construction start and duration, and other general market conditions. Ref-Construction Project Management Page 195

80. ________are the cash in your bank and other assets that can be converted into cash in less than one year. a. Current assets b. Balance c. Debts d. Credits

A...Explanation: Current assets are the cash in your bank and other assets that can be converted into cash in less than one year. Ref-Business Law and Project Management Page 13-3

58. __________ will secure someone's position within a company up to 12 weeks not paid, but still eligible to stay on the companies health insurance (if for Maternity reasons or other medical problems). a. Family and Medical Leave Act b. Americans with Disabilities Act c. IRS d. Any of the above

A...Explanation: FMLA will secure someone's position within a company up to 12 weeks not paid, but still eligible to stay on the companies health insurance (if for Maternity reasons or other medical problems). Certain other instances would apply as well, such as taking care of a husband/wife, mom/dad. Ref-Business Law and Project Management Page 10-7

75. Income Statement, Balance Sheet and Statement of Cash Flows are types of __________. a. Financial Statements b. IRS Documents c. Financial Liabilities d. None of the above

A...Explanation: Financial statements for businesses usually include: income statements, balance sheet, statements of retained earnings and cash flows, as well as other possible statements. Ref-Business Law and Project Management Page 13-3

49. Generally, the more efficient a building is, __________. a. The less it will cost to operate b. The more it will cost to operate c. The easier it will be to maintain d. The harder it will be to maintain

A...Explanation: Generally, the more efficient a building is the less it will cost to operate. Ref-Green Building Fundamentals Page 27

22. In a wall, reinforcement steel is kept in place by_______. a. Wire ties b. Concrete c. Shoring d. Nails

A...Explanation: In a wall, reinforcement steel is kept in place by wire ties. Ref- Placing Reinforcing Bars Page 11-27

38. In any general construction area where work is being performed, the least amount of light radiance is _______. a. 3 foot-candles b. 4 foot-candles c. 5 foot-candles d. 6 foot-candles

A...Explanation: In any general construction area where work is being performed, the least amount of light radiance is 3 foot-candles. Ref-OSHA Part 1926 Page 1926.56(a) Table D-3

30. Why is it important to track incoming cash and expenditures during the construction project? a. To ensure that you have enough working capital b. To balance the liabilities and debts c. To eliminate your debts d. It's a required part of project management

A...Explanation: It is important to track incoming cash and expenditures during the construction project to ensure you have enough working capital to complete the job. "Working Capital" refers to the amount of cash available after the liabilities or debts are paid. Ref-Business Law and Project Management Page 8-6

71. It is the _______ responsibility to furnish eye protection on jobsites when machines or operations present potential eye injury from physical, chemical, or radiation agents. a. Employer b. Contractor c. Building Official d. Subcontractor

A...Explanation: It is the employer's responsibility to furnish eye protection on jobsites when machines or operations present potential eye injury from physical, chemical, or radiation agents. Ref-OSHA Part 1926 1926.102(a)(1)

52. What two types of mortar are approved for laying masonry unit footings? a. Type M and S b. Type N and O c. Type M and N d. Type O and S

A...Explanation: Masonry units shall be laid in running bond and installed with Type M or S mortar. Ref-2015 IBC 1807.1.6.3(7)

63. The _____ will tell you what to do if there is an accident regarding dangerous liquids. a. MSDS b. ADA c. FMLA d. All of the above

A...Explanation: Material Safety Data Sheet (MSDS) is a formal document containing important information about the characteristics and actual or potential hazards of a substance. It identifies the manufacturer of the material (with name, address, phone, and fax number) and usually includes (1) chemical identity, (2) hazardous ingredients, (3) physical and chemical properties, (4) fire and explosion data, (5) reactivity data, (6) health hazards data, (7) exposure limits data, (8) precautions for safe storage and handling, (9) need for protective gear, and (10) spill control, cleanup, and disposal procedures. Mandated by the US Occupational Safety and Health Administration (OSHA). Ref-Business Law and Project Management Page 11-6

60. Why should you perform the slump test? a. To measure the stiffness of concrete b. To measure the amount of lime in the mix c. To measure the amount of sand in the mix d. All of the above

A...Explanation: No explanation needed.

33. Steel deck is made by _____ structural grade sheet steel into a repeating pattern of parallel ribs. a. Cold forming b. Concrete c. Melting d. Separating

A...Explanation: Steel deck is made by cold forming structural grade sheet steel into a repeating pattern of parallel ribs. The strength and stiffness of the panels are a result of the shape of the ribs and the material properties of the steel. Deck lengths can be varied to suit job conditions but, because of shipping considerations, are usually less than 40'. Standard deck width varies with the product used but full sheets are usually 12", 18", 24", 30" or 36". Deck is typically furnished in a standard width with the ends square cut. Any cutting for width, such as at openings or for angular fit, is done at the job site. Ref-SDI Manual of Construction with Steel Deck Page 4

2. __________ specifically consider a building project's long-term impact on the environment. a. Sustainable practices b. Renewable practices c. Recyclable practices d. Green practices

A...Explanation: Sustainable practices specifically consider a building project's long-term impact on the environment. Ref-Green Building Fundamentals Page 1

28. Temperature and shrinkage steel, also known as ______________ rods are placed at right angles to the main stress resisting steel. a. Reinforcement b. Rectangular footings c. Combined footings d. All of the above

A...Explanation: Temperature and shrinkage steel, also known as reinforcement rods are placed at right angles to the main stress resisting steel. Ref-Placing Reinforcing Bars Page 5-7

13. The spacing of Trusses along bearing support must be within _____ of plan dimension. a. +/- 1/4" b. +/- 1/2" c. +/- 1" d. +/- 2"

A...Explanation: The spacing of Trusses along bearing support must be within +/- ¼" of plan dimension. Field conditions that force spacing beyond this tolerance shall be reviewed and approved by the Building Designer and Truss Designer. Ref-BCSI Guide to Good Practice for Handling, Installing, Restraining & Bracing of Metal Plate Connected Wood Trusses Page 11

6. You would use a ______ contract when you have no way of knowing the exact span of the project. a. Unit Price b. Lump Sum c. Cost Plus d. None of the above

A...Explanation: This kind of contract is based on estimated quantities of items included in the project and their unit prices. The final price of the project is dependent on the quantities needed to carry out the work. Ref-Business Law and Project Management Page 7-5

90. Reference (IRS) provides a handbook to help employers: an Employers Tax Guide, commonly referred to as _______ and also known as Publication 15. a. Circular D b. Circular E c. Circular F d. Circular G

B...Explanation: (IRS) provides a handbook to help employers: an Employers Tax Guide, commonly referred to as Circular E — and also known as Publication 15 or Federal Tax Circular E, or IRS Circular E. Ref-Business Law and Project Management Page 14-3

65. Which of the following best describes a company's legal debts or obligations that arise during the course of business operations? a. Assets b. Liabilities c. Operations d. Income

B...Explanation: A company's legal debts or obligations that arise during the course of business operations. Ref-Business Law and Project Management Page 13-3

82. W-2 forms should be mailed out to employees by no later than ________ for forms derived from the previous calendar year. a. January 1 b. January 31 c. April 16 d. December 1

B...Explanation: According to the Internal Revenue Service, W-2 forms should be mailed out to employees by no later than January 31 for forms derived from the previous calendar year. While employees may not receive them in the mail on this date, they must -- at the very least -- be sent out at this point. Ref-Business Law and Project Management Page 14-6

78. Assets, Liabilities and Owners Equity are on a __________. a. Income Statement b. Balance Sheet c. Cash Flow d. Inventory

B...Explanation: The balance sheet is a snapshot of your business financials. It includes assets, and liabilities and net worth. The "bottom line" of a balance sheet must always include (assets = liabilities + net worth). Ref-Business Law and Project Management Page 13-3

96. Under the _______, income is counted when the sale occurs, and expenses are counted when you receive the goods or services. a. Credit method b. Accrual method c. Cash method d. None of the above

B...Explanation: Accrual method is a system of accounting based on the accrual principal, under which revenue is recognized (recorded) when earned, and expenses are recognized when incurred. Totals of revenues and expenses are shown in the financial statements (prepared at the end of an accounting period), whether or not cash was received or paid out in that period. Accruals basis accounting conforms to the provisions of GAAP in preparing financial statements for external users, and is employed by most companies except the very small ones (which use cash basis accounting). Ref-Business Law and Project Management Page 13-7

66. When admixtures are used for water reduction and setting time modification they shall conform with which of the following Standards?

B...Explanation: Admixtures for water reduction and setting time modification shall conform to ASTM C494. Admixtures for use in producing flowing concrete shall conform to ASTM C1017.

93. Which is the most dangerous effect of air bubbles in mortar? a. Interrupts consistency of mortar b. Weakens mortar strength c. Changes the chemical composition d. Changes texture

B...Explanation: Air bubbles in mortar weaken mortar strength, which is the most dangerous effect.

47. Average new construction projects traditionally generate about ______ of waste per square foot of building area. a. 2 pounds b. 4 pounds c. 6 pounds d. 8 pounds

B...Explanation: Average new construction projects traditionally generate about 4 pounds of waste per square foot of building area. Ref-Green Building Fundamentals Page 97

85. What is the MINIMUM size covered mall building that is required to have a standby power system? a. Greater than 40,000 sq. feet b. Greater than 50,000 sq. feet c. Greater than 60,000 sq. feet d. Greater than 70,000 sq. feet

B...Explanation: Covered mall buildings greater than 50,000 square feet and open mall buildings greater than 50,000 square feet within the established perimeter line shall be provided with standby power systems that are capable of operating the emergency voice/alarm communication system. Ref-2015 IBC 402.7.3

64. On construction sites, exit passageway enclosures shall have walls, floors and ceilings of not less than a ____ fire-resistance rating, and not less than that required for any connecting interior exit stairway or ramp. a. 1/2-hour b. 1-hour c. 2-hours d. 3-hours

B...Explanation: Exit passageway enclosures shall have walls, floors and ceilings of not less than a 1-hour fire-resistance rating, and not less than that required for any connecting interior exit stairway or ramp. Exit passageways shall be constructed as fire barriers in accordance with Section 707 or horizontal assemblies constructed in accordance with Section 711 or both. Ref-2015 IBC 1024.3

40. The employee must fill out Form I-9 that shows his or hers identity and employment authorization within _____________ of the date employment begins. a. One business day b. Three business days c. Seven business days d. No time limit

B...Explanation: Form I-9 helps employers to verify individuals who are authorized to work in the United States. You must complete Form I-9 each time you hire any person to perform labor or services in the United States in return for wages. Ref-Business Law and Project Management Page 10-5

16. It is estimated that green buildings use an average of __________ energy than conventional buildings. a. 26% less b. 36% less c. 46% less d. 56% less

B...Explanation: It is estimated that green buildings use an average of 36% less energy than conventional buildings and that they have corresponding reductions in CO2 emissions. Ref-Green Building Fundamentals Page 29

31. Activity on arrow and activity on node are both examples of which method of scheduling? a. Bar chart b. Network c. Matrix d. Linear Matrix

B...Explanation: Network schedules can take two forms: activity on arrow notation or activity on node notation. Ref-Construction Project Management Page 229

4. Concrete used for building foundations included in Seismic Design Category A, B or C shall have what MINIMUM specified compressive strength? a. 2,000 lbs. b. 2,500 lbs. c. 2,800 lbs. d. 3,000 lbs.

B...Explanation: Ref-2015 IBC Table 1808.8.1

95. In _______ depreciation method, depreciation is charged uniformly over the life of an asset. a. Simple line b. Straight line c. Amortization d. None of the above

B...Explanation: Ref-Business Law and Project Management Page 13-11. The formula to calculate the straight-line depreciation of an asset for a full accounting period is: Depreciation = Cost − Salvage Value Life in Number of Periods Example 1: On Jan 1, 2015 Company ABC purchased a vehicle costing $40,000. It is expected to have a value of $1,000 at the end of 4 years. Calculate depreciation expense on the vehicle for the year ended Dec 31, 2015. Solution: We will first find the depreciable amount, which is $30,000 ($40,000 cost minus$10,000 residual value). Then we divide the depreciable amount by the 4, which is the useful life of the vehicle. This will give a figure of $7,500 for the yearly depreciation. Or by using the formula Depreciation = ($40,000 − $10,000) / 4 = $7,500

99. Skylights shall not be installed in the plane of the roof where the roof pitch is less than ______ from the horizontal. a. 30 degrees b. 45 degrees c. 60 degrees d. 90 degrees

B...Explanation: Skylights shall not be installed in the plane of the roof where the roof pitch is less than 45 degrees from the horizontal. Ref-2015 IBC 2405.4

89. Strength tests for shotcrete shall be made by an approved agency on specimens that are representative of the work and which have been water soaked for at least _______ prior to testing. a. 12 hours b. 24 hours c. 36 hours d. 48 hours

B...Explanation: Strength tests for shotcrete shall be made by an approved agency on specimens that are representative of the work and which have been water soaked for at least 24 hours prior to testing. When the maximum-size aggregate is larger than 3/8 inch, specimens shall consist of not less than three 3- inch-diameter cores or 3-inch cubes. When the maximum-size aggregate is 3/8 inch or smaller, specimens shall consist of not less than 2-inch-diameter cores or 2-inch cubes. Ref-2015 IBC 1908.10

18. Swales are __________ that are constructed out of soil and used to direct the flow of runoff water. a. Roads b. Channels c. Rafters d. Solar panels

B...Explanation: Swales are channels that are constructed out of soil and used to direct the flow of runoff water. Ref-Green Building Fundamentals Page 51

51. The building official is __________ to suspend or revoke a permit issued under the provisions of the code wherever the permit is issued in error or on the basis of incorrect, inaccurate or incomplete information, or in violation of any ordinance or regulation. a. Not Authorized b. Authorized c. Only the contractor can make changes to the permit d. Only the owner can make changes to the permit

B...Explanation: The building official is authorized to suspend or revoke a permit issued under the provisions of this code wherever the permit is issued in error or on the basis of incorrect, inaccurate or incomplete information, or in violation of any ordinance or regulation. Ref-2015 IBC 105.6

21. Steel joists must be manufactured to specifications from the Steel Joist Institute. Which of the following is NOT a specification from SJI? a. SJI K b. SJI M c. SJI LH/DLH d. SJI JG

B...Explanation: The design, manufacture and use of open web steel joists and joist girders shall be in accordance with one of the following Steel Joist Institute (SJI) specifications: Ref-2015 IBC 2207.11. 1. SJI CJ 2. SJI K 3. SJI LH/DLH 4. SJI JG

8. What is the MINIMUM clear width of each door opening in a commercial building? a. 31" b. 32" c. 33" d. 34"

B...Explanation: The minimum width of each door opening shall be sufficient for the occupant load thereof and shall provide a clear width of 32 inches. Clear openings of doorways with swinging doors shall be measured between the face of the door and the stop, with the door open 90 degrees. Ref-2015 IBC 1010.1.1

77. The thickness of concrete floor slabs supported directly on the ground shall not be less than _______. a. 2 1/2 inches b. 3 1/2 inches c. 4 1/2 inches d. 5 1/2 inches

B...Explanation: The thickness of concrete floor slabs supported directly on the ground shall not be less than 3 1/2 inches. Ref-2015 IBC 1907.1

44. How should you determine the perimeter dimension from blueprints? a. It can't be done b. Add first in one direction, then in the other direction c. Add clockwise d. Use rendition drawings

B...Explanation: To determine the perimeter dimension from blueprints, first add in one direction, then in the other direction, since it doesn't really matter in which direction you add.

23. Top Chord bearing flat or Parallel Chord Trusses shall be installed so that the gap between the inside edge of the bearing and the first diagonal or vertical web member does not exceed____. a. 1/4" b. 1/2" c. 1" d. 2"

B...Explanation: Top Chord bearing flat or Parallel Chord Trusses shall be installed so that the gap between the inside edge of the bearing and the first diagonal or vertical web member does not exceed 1/2". Ref-BCSI Guide to Good Practice for Handling, Installing, Restraining & Bracing of Metal Plate Connected Wood Trusses Page 11

45. When not specified, concrete that is placed in contact with the ground must have how much concrete cover at the sides of the reinforcing bars? a. 2" b. 3" c. 4" d. 5"

B...Explanation: When not specified, 3" at sides is the least amount of coverage. Ref-Placing Reinforcing Bars Page 11-3

32. 30 inches is the minimum diameter of a collapsible spiral with a spiral bar of what size? a. 7/8" b. 1/2" c. 5/8" d. Any of the above

C...Explanation: 5/8". Ref-Placing Reinforcing Bars Page 6-11

27. A general rule of thumb is that thermal mass materials are effective at absorbing heat only up to about _____. a. 4 inches b. 5 inches c. 6 inches d. 7 inches

C...Explanation: A general rule of thumb is that thermal mass materials are effective at absorbing heat only up to about 6 inches. Ref-Green Building Fundamentals Page 63

14. Adobe units shall have an average compressive strength of? a. 100 psi b. 200 psi c. 300 psi d. 400 psi

C...Explanation: Adobe units shall have an average compressive strength of 300 psi. Ref-2015 IBC 2109.3.1.1

92. An Employer Identification Number (EIN) is also known as a Federal Tax Identification Number, issued by _____ and is used to identify a business entity. a. USDA b. NSA c. IRS d. All of the above

C...Explanation: An Employer Identification Number (EIN) is also known as a Federal Tax Identification Number, and is used to identify a business entity. Generally, businesses need an EIN. This is a free service offered by the Internal Revenue Service and you can get your EIN immediately. Ref-Business Law and Project Management Page 14-1

50. How many square feet does a circular slab of 50 feet in diameter cover? a. Over 1,200 b. Under 1,500 c. Over 1,962.5 d. Over 2,188.25

C...Explanation: Area = 3.14 x r2 3.14 x (25 x 25) = 1962.5 sq. ft.

29. Which of the following is a limitation of a bar chart schedule? a. Scheduling information is presented at a summary level b. Ease of preparation c. Does not communicate the interrelationships among project activities d. Ease of interpretation

C...Explanation: Bar Chart does not communicate the interrelationships among project activities. Ref-Construction Project Management Page 225

39. What could happen if you purposely violate the Fair Labor Standards Act? a. Fines up to $10,000 b. Criminal charges could be filed against you c. Both A and B d. None of the above

C...Explanation: Both A and B are correct. Ref-Business Law and Project Management Page 10-5

81. Light-weight concrete shall contain aggregate that meets the density specifications determined by_____. a. ASTM C330 b. ASTM C33 c. ASTM C567 d. ASTM C496

C...Explanation: Concrete containing lightweight aggregate and an equilibrium density, as determined by ASTM C567, between 90 and 115 lb/ft3. Ref-ACI 318 2.2

5. A _____ contract is when a single business is contracted to do the job from beginning to end. a. Cost Plus b. Turnkey c. Design/Build d. Lump Sum

C...Explanation: Design-build is a method of project delivery in which one entity (the design-build team) works under a single contract with the project owner to provide design and construction services. Ref-Business Law and Project Management Page 7-6

46. Employers with __________ people on staff are not required by law to follow the ADA (Americans with Disabilities Act). a. Less than 5 b. Less than 10 c. Less than 15 d. Less than 30

C...Explanation: Employers with less than 15 people on staff are not required by law to follow the ADA (Americans with Disabilities Act). Ref-Business Law and Project Management Page 10-6

41. It is mandated that an I-9 form for every employee be stored for how long? a. 3 years from the date the person was hired b. 1 year after termination c. The longest of the first two options d. None of the above

C...Explanation: Forms I-9 must be stored for three years after the date you hire an employee, or one year after the employee's employment ends, whichever is later, which can result in a long retention period. For example, if an employee retires from your company after 15 years, you will need to store his or her Form I-9 for a total of 16 years. Ref-Business Law and Project Management Page 10-5

20. If a noise decibel level of 110db for 60 minutes at a time occurs, it is still within acceptable limits. a. The statement above is correct b. No, only 45 minutes are allowed c. No, only 30 minutes are allowed d. No, only 15 minutes are allowed

C...Explanation: If a noise decibel level of 110db for 60 minutes at a time occurs, it is NOT within acceptable limits. Ref-OSHA Part 1926 Page 1926.52 (Table D-2) and 1926.52 (d)(2)(iii)

36. In a network schedule, what is the fundamental unit of work? a. Node b. Event c. Activity d. Arrow

C...Explanation: In network scheduling each item of work is called an activity. These activities are each given a duration (in hours, days, weeks, etc.), and they are connected by network diagrams. Ref-Construction Project Management Page 229

43. Only those installation drawings that have been stamped ______________ should be used for deck erection. a. "APPROVED FOR USE" b. "STAMPED FOR CONSTRUCTION" c. "APPROVED FOR CONSTRUCTION" d. "APPROVED FOR CONTRACTORS"

C...Explanation: Only those installation drawings that have been stamped "APPROVED FOR CONSTRUCTION" i.e."FIELD USE" should be used for deck erection. Ref-SDI Manual of Construction with Steel Deck Page 12

70. What is the MINIMUM specified compressive strength at 28 days for concrete driveways exposed to severe weather conditions? a. 2500 b. 3000 c. 3500 d. None of the above

C...Explanation: Ref-2015 IBC 1904.2

76. How many of the units must be accessible with roll-in showers for a newly built hotel, which contains 290 sleeping units. a. 1 unit b. 2 units c. 3 units d. 4 units

C...Explanation: Ref-2015 IBC Table 1107.6.1.1

94. Which of the following hazard categories requires barricade construction for explosion control? a. Flammable liquids b. Cryogenic flammables c. Organic peroxides d. Pyrophoric gas

C...Explanation: Ref-2015 IBC Table 414.5.1

57. What is the MAXIMUM allowed number of stories in height for Group R-4 occupancy in Type IIB construction?

C...Explanation: Ref-2015 IBC Table 504.4

73. In order for a safety net to provide for falls on the perimeter of the work surface, they should extend out ________ feet beyond that surface. a. 6 b. 7 c. 8 d. 9

C...Explanation: Safety nets shall extend 8 feet beyond the edge of the work surface where employees are exposed. Ref-OSHA Part 1926 1926.105 (c)(1)

100. Which of the following buildings would be classified as an A-3 occupancy? a. Restaurants b. Theaters c. Museums d. Taverns

C...Explanation: The Group A-3 occupancy includes assembly uses intended for worship, recreation or amusement and other assembly uses not classified elsewhere in Group A. Ref-2015 IBC 303.4

97. The _______ is the more commonly used method of accounting in small business. a. Credit method b. Accrual method c. Cash method d. None of the above

C...Explanation: The cash method is the more commonly used method of accounting in small business. Under the cash method, income is not counted until cash (or a check) is actually received, and expenses are not counted until they are actually paid. Ref-Business Law and Project Management Page 13-7

69. The _________ must supply, maintain and require hard hats to be worn on his jobsite in areas where there is a possible danger of head injury from impact. a. Contractor b. Building Official c. Employer d. Subcontractor

C...Explanation: The employer must provide each employee with head protection that meets the specifications for employees working in areas where there is a possible danger of head injury from impact, or from falling or flying objects, or from electrical shock and burns. Ref-OSHA Part 1926 1926.100 (b)(1)

11. The __________ is the most difficult factor to determine because both the hourly wage rate and crew productivity must be considered. a. Unit Pricing b. Material Costs c. Labor Costs d. All of the above

C...Explanation: The price of labor is the most difficult factor to determine because both the hourly wage rate and crew productivity must be considered. Ref- Construction Project Management Page 210

79. Approximately how many concrete blocks 8W x 10H x 12L are required for a wall 50' long and 6' high? a. 120 b. 250 c. 360 d. 500

C...Explanation: The simplest way to approach this problem is to convert the wall and block dimensions to square inches and divide wall area by block area. 50ft = 600in & 6ft = 72in Wall area: 600 x 72 = 43,200 sq. in. Block Face area: 10 x 12 = 120 sq. in. 43,200 ÷ 120 =360 blocks

84. Calculate the total price for 200 2" x 4"x 100" boards at 80 cents per board foot? a. $1,370 b. $2,660 c. $888 d. $970

C...Explanation: Thickness x Width x Length (in inches) divided by 144 is equal to the board foot measure of those dimensions. (2x4x100) ÷144 = 5.5 board feet. 5.5bf/boards x 200 boards needed =1,111bf x $0.80/bf =$888

74. How many board feet are in a 1" x 9" x 96"-long board? a. 8 b. 10 c. 6 d. 5

C...Explanation: To calculate the number of board feet in a piece of lumber, multiply the board's thickness by its width, then its length, all in inches. Then divide by 144 to get the answer. 1 x 9 x 96 = 864 / 144 = 6

54. State and Federal unemployment taxes must be paid by a company if there is one or more employees on their payroll for ____ in a year. a. 10 weeks b. 15 weeks c. 20 weeks d. 30 weeks

C...Explanation: Unemployment Insurance (UI) is a federal-state program jointly financed through Federal and state employer payroll taxes (federal/state UI tax). Generally, employers must pay both state and Federal unemployment taxes if: (1) they pay wages to employees totaling $1,500, or more, in any quarter of a calendar year; or, (2) they had at least one employee during any day of a week during 20 weeks in a calendar year, regardless of whether or not the weeks were consecutive. Ref-Business Law and Project Management Page 10-11

10. A_____ define the contractor's liability for the repair of defects to the construction project after its completion. a. Contract b. Specification c. Warranty d. All of the above

C...Explanation: Warranty. Ref-Business Law and Project Management Page 7- 5

83. What is stamped on construction documents after they have been reviewed by the building department? a. "Accepted for Code Compliance" b. "Processed for Code Compliance" c. "Reviewed for Code Compliance" d. "Approved for Code Compliance"

C...Explanation: When the building official issues a permit, the construction documents shall be approved, in writing or by stamp, as "Reviewed for Code Compliance." One set of construction documents so reviewed shall be retained by the building official. The other set shall be returned to the applicant, shall be kept at the site of work and shall be open to inspection by the building official or a duly authorized representative. Ref-2015 IBC 107.3.1

86. IRS Form _____ is due on Jan. 31st. a. 1040 b. 8062 c. 940 d. None of the above

C...Explanation: You are only required to deposit FUTA taxes if the liability during any quarter exceeds $500. However, if you expect to pay less than $500 in FUTA taxes for the year, you can pay the tax with your Form 940 return, which is due and payable January 31, of the following tax year. Ref-Business Law and Project Management Page 14-6

7. _______ contract is an agreement wherein the purchaser agrees to pay the cost of all labor and materials plus an amount for contractor overhead and profit. a. Unit Price b. Lump Sum c. Cash Sum d. Cost Plus

D...Explanation: A contract agreement wherein the purchaser agrees to pay the cost of all labor and materials plus an amount for contractor overhead and profit (usually as a percentage of the labor and material cost). Ref-Business Law and Project Management Page 7-6

42. What would be considered acceptable proof of eligibility to work for a company associated with filling out the I-9 form? a. Drivers License with Social Security Card b. Alien Registration receipt with picture c. Certificate of U.S. Citizenship d. All of the above

D...Explanation: All of the above. Ref-Business Law and Project Management Page 10-6

68. Expansive soil is usually treated with: a. Lime treatment b. Sand treatment c. Moisture treatment d. Any of the above

D...Explanation: All the answers provided are correct.

62. If a company has _ people on payroll, they are not required to have an Emergency Action Plan in writing mandated by OSHA. a. 3 b. 6 c. 9 d. All of the above

D...Explanation: An emergency action plan must be in writing, kept in the workplace, and available to employees for review. However, an employer with 10 or fewer employees may communicate the plan orally to employees. Ref-Business Law and Project Management Page 11-3

17. When a contractor is compensated for expenses associated with the work and supplies in addition to the operating cost and revenue, it is called a ____ contract. a. Lump Sum b. Liability c. Design/Build d. Cost Plus

D...Explanation: Cost Plus. Ref-Business Law and Project Management Page 7- 5

9. How long after work is suspended or abandoned does a permit expire? a. 30 days b. 60 days c. 90 days d. 180 days

D...Explanation: Every permit issued shall become invalid unless the work on the site authorized by such permit is commenced within 180 days after its issuance, or if the work authorized on the site by such permit is suspended or abandoned for a period of 180 days after the time the work is commenced. The building official is authorized to grant, in writing, one or more extensions of time, for periods not more than 180 days each. The extension shall be requested in writing and justifiable cause demonstrated. Ref-2015 IBC 105.5

34. Exposure to impulsive or impact noise should not exceed _______ sound pressure level. a. 110 dB peak b. 120 dB peak c. 130 dB peak d. 140 dB peak

D...Explanation: Exposure to impulsive or impact noise should not exceed 140 dB peak sound pressure level. Ref-OSHA Part 1926 Page 1926.52(e)

19. Which of the following documents is NOT required for each job? a. Contract b. Construction drawings c. Specifications d. Fax Cover sheet

D...Explanation: Fax Cover sheet. Ref-Business Law and Project Management Page 6-2

91. What is the MAXIMUM flame spread index allowed for fire retardant treated wood? a. 10 b. 15 c. 20 d. 25

D...Explanation: Fire-retardant-treated wood is any wood product which, when impregnated with chemicals by a pressure process or other means during manufacture, shall have, when tested in accordance with ASTME 84 or UL723, a listed flame spread index of 25 or less and show no evidence of significant progressive combustion when the test is continued for an additional 20-minute period. Ref-2015 IBC 2303.2

59. What is the MAXIMUM allowed travel distance to toilet facilities in an office building for employees and the public? a. 100 feet b. 200 feet c. 400 feet d. 500 feet

D...Explanation: In occupancies other than covered mall buildings, the required public and employee toilet facilities shall be located not more than one story above or below the space required to be provided with toilet facilities and the path of travel to such facilities shall not exceed a distance of 500 feet. Ref-2015 IBC 2902.3.2

98. ________ measure the ability of a company to meet its short-term debt obligations. a. Liabilities b. Current assets c. Owner's equity d. Liquidity ratios

D...Explanation: Liquidity ratios are the ratios that measure the ability of a company to meet its short-term debt obligations. If the value is greater than 1, it means the short-term obligations are fully covered. The three key liquidity ratios include the current, quick, and the cash ratio. Each of these measures has the same basic structure, whereby assets are placed in the numerator and liabilities in the denominator. The word "liquidity" is used to describe how easily an asset can be converted into cash. As a rule of thumb, the value of these liquid assets should be twice as high as the company's short-term debt obligations. Ref- Business Law and Project Management Page 13-6 Formulas: Liquidity Ratio = Current Assets / Current Liabilities Quick Ratio = Current Assets - Inventory / Current Liabilities Debt Ratio = Total Debt / Total Assets Profitability Ratio = Net Income / Revenues

61. What is the MINIMUM corridor width where a required occupancy has a capacity less than 50? a. 30" b. 32" c. 34" d. 36"

D...Explanation: Ref-2015 IBC Table 1020.2

48. In a building that is classified as an F-1 occupancy, how many water closets are required? a. 1 per 25 b. 1 per 50 c. 1 per 75 d. 1 per 100

D...Explanation: Ref-2015 IBC Table 2902.1

72. A fall protection belt has to be minimum of _" nylon to provide for a fall of no greater than _______feet. a. 3 b. 4 c. 5 d. 6

D...Explanation: Safety belt lanyard shall be a minimum of 1⁄2-inch nylon, or equivalent, with a maximum length to provide for a fall of no greater than 6 feet. Ref-OSHA Part 1926 1926.104(d)

26. The principle of economy of scale is an important factor when addressing project size, essentially, as projects get bigger, a. They get less expensive but at a less rapid rate. b. They get more expensive at a faster rate. c. They get less expensive at a faster rate. d. They get more expensive but at a less rapid rate.

D...Explanation: The principle of economy of scale is an important factor when addressing project size. Essentially, as projects get bigger, they get more expensive but at a less rapid rate. This occurs because the larger the project, the more efficiently people and equipment can be used. Also, as people repeat a task, they get better and faster, reducing the cost of labor. Ref-Construction Project Management Page 196

56. When a preconstruction load test is conducted, what is the MINIMUM amount of time the test shall be left in place? a. 6 hours b. 10 hours c. 18 hours d. 24 hours

D...Explanation: The test load shall be left in place for a period of 24 hours. The tested assembly shall be considered to have successfully met the test requirements if the assembly recovers not less than 75 percent of the maximum deflection within 24 hours after the removal of the test load. Ref-2015 IBC 1709.3.1

1. Which of the following type of financial statements companies use? a. Balance sheet b. Income Statement c. Statement of cash flows d. All of the above

D...Explanation: There are three types of financial statements companies use: balance sheet, income statement, and statement of cash flows. Ref-Business Law and Project Management Page 13-3

88. If you spend more than $600 a year paying subcontractors, you would report that on IRS Form ________. a. W-2 b. 940 c. 1040A d. 1099-MISC

D...Explanation: This form is used to report income to independent contractors, and other self-employed individuals who, as their own employer, are generally responsible for paying their share of taxes. Ref-Business Law and Project Management Page 14-6

87. What type of construction is classified as heavy timber? a. Type I b. Type II c. Type III d. Type IV

D...Explanation: Type IV construction (Heavy Timber, HT) is that type of construction in which the exterior walls are of noncombustible materials and the interior building elements are of solid or laminated wood without concealed spaces. Ref-2015 IBC 602.4