Solid Professor (5-15)
Which of the following can NOT be used as a path for the Sweep Command?
Planes
Which of the following is NOT an option in the Thread Command Window?
Diameter
What happens when the web command does not have geometry to end at?
The web can not be created
Drafts can only be applied to a 3D model when performing an extrude. True or False?
False
Only straight lines that are coincident with the edge of a 3D body can be used as a selection by the Web Command. True or False?
False
The Slide Edge Command moves the adjacent edges around the T-Spline body to adjust the geometry's contour. True or False?
True
Quad Ball command
more akin to six-sided cube that had been pulled out to form a perfect sphere and contains 8 STAR POINTS
The four Plane types are:
-Offset Plane -Plane at an angle -Tangent Plane -Midplane
How many star points does a Quad Ball have?
8
What must be selected in order to perform the Redefine Sketch Plane Command?
A Plane or 3D surface
The Point at Edge and Plane Command requires:
A plane or face to be selected along with a linear edge or sketch line
Drafts can be created in which of the following directions?
All of these are correct (Two side, One Side, and Symmetric)
Edit Form
Allows for sets of vertices, edges, and faces to be manually pushed and pulled in different directions
Redefine Sketch plane
Allows for sketches to be relocated to a new plane
Draft Command
An angle added to any planar face
The Subdivide Command
Can add a lot of detail by grouping faces and splitting them into equally spaced faces
Points
Can be added through construction geometry's when a point is not present in the model
Insert point command
Can be used to divide faces into custom shapes by selecting points on adjacent edges to create a new edge between
Measure Command
Can measure key parts of a model
Combine Command
Combines bodies together
Press and Pull
Command that allows you to access the extrude, fillet, and offset face command
Sweep Command
Creates geometry by extending a closed profile along a path
Section Analysis
Cuts through components in the model to see interior spaces in the model
Which of the following is NOT a Construction Point Command?
Cylindrical Point
Dimensions
Dimensions are applied to sketch entities to define their lengths, angles, radii, diameters, etc.
Putting related profiles on the same sketch makes it impossible to perform the Revolve command. True or False?
False
Since the "Smooth Display" mode is much less memory intensive, it is often efficient to edit the model in that mode and switch to "Box Display" for final adjustments. True or False?
False
The Loft Command can only be used between dissimilar profiles. True or False?
False
The Revolve Command is NOT able to create new components. True or False?
False
The Section Analysis Command will often end up adding/removing 3D geometry from the model. True or False?
False
The Weld Vertices Command will have the same effect on both a symmetrical body and a non-symmetrical one. True or False?
False
The mirror Command is only capable of selecting one object to mirror at a time. True or False?
False
When using Insert Edge, multiple loops can be selected for T-Spline edge selection. True or False?
False
When using the "Loft" command, Fusion 360 automatically connects all of the available sketch profiles on screen, while also influencing the direction of the lofted body. True or False?
False
When using the Delete Command to erase vertices, only the entities (including vertices and faces) completely enclosed will be selected and deleted. True or False?
False
Fillet command
Fillets are used to cut internal edges of a model or to reduce high stress concentrations along a model edge
What is the Main difference between the Fillet and Chamfer Commands?
Fillets create round edges while Chamfers create angled faces
Which of the following is NOT a Hole Type found in the Hole Command
Flat-Head
Box display
Gives up vital fidelity but reduces processing power required to generate models with many faces, so your model still retains responsiveness, good for speed
Insert Edge
Inserts edges at a specified position from the original edge
Weld Vertices
Joins two vertices together on sculpted bodies
When the "Keep Tools" option is checked, the Combine Command will...
Keep the original Tool Bodies after completing the command
Break Link to Projected Geometry
Makes the projected geometry independent from the original geometry
The modify command is very good at...
Making T-Spline bodies manageable and detailed by adding and removing faces, edges, or vertices
The Edit Form Command can perform a combination of which of the following commands
Move, Rotate, Scale
What two selections must be made in order to define what is duplicated in a Rectangular Pattern?
Objects, Directions
Scale Command
Scales up or down sketches
How would you use the Shell Command to hollow out a body without removing any faces?
Select the entire body for the Faces/Body section of the Shell Command
Vertex to midpoint
Selected vertices will be welded at the midpoint between them
Split Body Command
Separates the body's in the model
Which of the following is Not a type of Construction Plane?
Symmetric Plane
Revolve command
Takes a closed sketch profile(s) and rotates them around an axis to create a three-dimensional profile
Extrude Command
Takes an existing sketch or face and adds depth by projecting, or extruding it out linearly in order to create 3d geometry
What command can be used to copy objects around a center point?
The Circular Pattern command
Which Extrude option allows you to join two or more extruded bodies together?
The Join option
Smooth display
The default display when working with T-Spline bodies, good for details
The display mode command can be accessed from...
The toolbar, which can switch the display of the model by selecting entities on the model
Which of the following is not a Boolean operation found within the Combine Command?
Unite
Weld to Tolerance
Used as a distance check
Offset
Using the offset command is a quick and easy way to recreate and scale geometry, but it can only offset on enclosed profile at a time even if they were created from a single sketch element
Which of the following can be created when applying Primitives?
Water-tight volumes and Surface Bodies
Parameters
like mathematical variables that can edit many model geometries across a canvas
Sketch Fillet
A sketch fillet is a sketch element that is used to create a smooth transition by adding a tangent arc between 2 elements
Design Intent
Strategy where geometry is defined in such a way that changes produce desired, predictable results
Intersect
The intersect command is used to copy the models contours into the sketch where the plane cuts through the model
In order to complete a Circular Pattern, both the desired objects and an axis MUST be selected. True or False?
True
The Offset command can only be used to modify one enclosed profile at a time. True or False?
True
The Offset command is unable to create new sketch geometry, it can only create derived geometry from and existing sketch. True or False?
True
The mirror command can use a construction line as the line of symmetry. True or False?
True
Threads can only be added to cylindrical faces. True or False?
True
When analyzing a model, the Interference Detection Command can be used to identify any overlapping bodies within a model. True or False?
True
Web Command
Used to create geometry from sketch curves that intersect with pre-existing bodies
Shell Command
Used to hollow out material and create thin walls in the part - remove faces from the model
Planes
Used to place sketches in specific angles relative to the model
Vertex to Vertex
Welds the selected vertices by moving the FIRST on selected to the second
Edit form facts
-Can be accessed in the modify drop down, the right click menu, and the toolbar -Like a combination of the scale, move, and rotate command -The coordinate space defines what type of axis is used for manipulation -Object Snap allows you to snap to the closest geometry -Soft modification allows you to change the area of influence your modifications will have on the rest of the model, and, when enabled is visually represented with red and white highlighting
Threads Command
Adds simple thread types to any cylindrical face
Which of the following is NOT a Loft type demonstrated in the videos?
Sketch LOft
Trim and Extend
Used to clean up and refine the geometry without having to resketch entire sections
Slide edge
allows you to reposition and edge in a particular direction
Rib Command
Adds geometry to a model based on a single sketch element that intersect with already created geometry
Delete Vertices
Deletes vertices, very important because the shape of the body is determined by the placement of the vertices
Direct Modeling
Directly edits surfaces and faces of a design without regard for previously established relationships
Managing the Number of faces
The amount of detail in the body is directly related to how many faces the model has
The Rib command requires pre-existing geometry and can not be added alone. True or False?
True
Which of the following is NOT an acceptable object to define a direction for a Rectangular Pattern Command?
A dimension
Which of the following is a type of Construction Axis Command?
All of these are correct (Axis Perpendicular to Face at Point, Axis Through Two Planes, and Axis through Cylinder/Cone/Torus)
Yellow capped faces are the only areas where a crease can be applied. True or False?
False
What command can be used to replicate or pattern an object linearly about a sketch?
The Rectangular Pattern Command
Rectangular Pattern
The Rectangular Pattern command takes the original geometry and replicates it across the sketch with a specified spacing in a number of instances
What command can be used to correct downstream issues that can occur when deleting reference geometry?
The Redefine Sketch Plane command
Mirror
The mirror command copies and flips sketch entities across a line of symmetry and creates a relationship between the mirror and original entity
After performing a Mirror Command, the resulting geometry will automatically update if the original geometry is modified. True or False?
True
In the Measure Command, until the selection is cleared, the first selection made will always be used as the reference for the measurement. True or False?
True
Once you create a sketch using the projected geometry command, it will update to match any changes made to the original geometry. True or False?
True
The Curvature Spacing option in the extrude command produces denser T-Spline geometry along areas of high curvature, while the Uniform option spaces the T-spline vertices equally across the geometry. True or False?
True
The Extrude Command creates 3D geometry by moving a face or sketch profile along a linear path. True or False?
True
The Intersect Command creates sketch geometry that references the cross section of a model. True or False?
True
The Project Command can be accessed simply by pressing the P key on your keyboard. True or False?
True
The Shape of a Sweep feature will change if additional faces are added along the length of the path. True or False?
True
The Shell Command can remove material from multiple faces in the model. True or False?
True
The Trim Command Cuts line segments back to the nearest sketch entity. True or False?
True
To insert the Bevel edge, the bevel location uses a percentage marker between the beveled edge and the two closest edges on the other sides of the adjacent faces. True or False?
True
Unlike bodies, Sketches must be selected from the browser in order to apply the Scale Command to them. True or False?
True
Loft Command
Used to create geometry between enclosed profiles or points, and is most commonly used between dissimilar profiles, such as rectangles and circles
Hole Command
Adds holes without having to make time consuming sketches
Quad ball vs Sphere
Both create simple spheres, but they lay out the edges differently
Chamfer Command
Chamfers can be used whenever the edge of the model will be interacting with another model or component in an assembly
Which of the following options is dependent on the "Angle" option when applying the Revolve Command?
Direction
When working with T-Spline bodies, it is recommended to use the highest number of faces possible to get the exact shape, then start reducing faces to simplify the model. True or False?
False
Primitives
Starts off with simple base sketch Shapes like rectangles and circles and then it pulls it outward to give its final shape. There are many types of primitives in the create menu. primitives are often called "sculpted geometry"
Circular Pattern
The circular pattern command is used to copy the geometry around the sketch
Which of the following is NOT a type of fillet?
Variable Circumference
Bevel Edge
replaces a single edge with a specified number of adjacent edges
Axes
used to control model edges
