AutoCAD & Print Reading

The multiview method represents ____.

All of the above / the shape description of the object

The AUPREC system variable sets the number of decimal places for

Angular units

The CURSORSIZE system variable sets the size of the crosshairs

As a percentage of the screen size

what size designation is and 11"x17" sheet?

B

Hidden lines ___?

Both a and b

Orthographic projection ___.

Both a and b

Standard is the default text style in which of the following?

Both a and b

A scale that shows that 1"=60' is a(n)

Civil Engineer's Scale

Which system variable is used to edit attributes within a block?

DDEDIT / DDATTDEF /

Thin lines capped on the ends with arrowheads.

Dimension Line

Additional lines of text placed while still in the TEXT command will appear

Directly below the first line of text /

DTEXT stands for which of the following?

Dynamic text

A scale that reads 1:2 is a(n):

Half Scale

A scale that reads 1:2 is a(n):

Half scale

To enter a command from the keyboard, enter the command name at the On-screen prompt:

Lowercase, Uppercase or Mixed case

The command alias for MULTILINE is

MLINE / Both b and c

Which system variable controls the configuration of a multiline?

MLSTYLE

Which of the following commands "processes" text in paragraph form?

MTEXT

What size designation is an 11"x17" sheet?

Mechanical B

Which of the following sheet sizes is 1189x841mm?

Metric A0

Which of the following sheet sizes is 420x297mm?

Metric A3

Which of the following sheet sizes is 297x210mm?

Metric A4

Which object snap mode snaps to a point object?

Node

A short break line is always____.

None of the above

Also called visible lines.

Object Line

To view a different portion of the drawing without changing it's magnification use

PAN

To view a different portion of the drawing without changing its magnification use

PAN

The key combination Ctrl + V is equivalent to the command

PASTECLIP

If a mechanical drawing shows a scale of 1:4, what does this mean?

Quarter Scale

What method of coordinate entry is being used when the user enters @distance<angle?

Relative polar

Which option deletes objects from the selection set and is a switch from the Add mode?

Remove

The "S.E.R" options of the ARC command is short for

Short, End, Rotate

A print in which an object can adequately be communicated by using only a single view is called a ____.

Single View Drawing / None of the above / Partial View / One View drawing

Regarding the ARC options, what does "S.E.R." mean?

Start, End, Radius

In the Auto option, if the target box does not touch an object when you pick a point, the selection method becomes either Window or Crossing.

TRUE

One option of the GROUP command is whether a group is selectable or not.

TRUE

When possible, a multiview shows the surface of the object in its true size and shape.

TRUE

The RECTANG command requests what information when drawing a rectangle?

The coordinates of diagonally opposite corners of the rectangle

Keeping in mind that the intent of a print is to communicate the manufacture of a product easily, which of the following are true?

Use enough views to describe the shape of the object accurately and completely. AND the accenting of rounded curves should be shown in multiviews with a phantom line so the curves are clearly accented.

The front view of and object should:

all of the above

An ERASE LAST command issued after the LINE command will result in

deletion of the last line segment

CHAMFERA & CHAMFERB system variables are used to set chamfer

distances

The height of an object shown in a multiview print is common between ____.

the front view and the right side view

If you see the width and height dimensions of an object in third-angle projection, which views of the multiview print are shown?

the front view, the right side view, and the top view / The Front View and the Right Side View /

In first-angle projection ____.

the object to be drawn is placed in the upper left quadrant, or the first quadrant AND the object is between the viewer's line of sight and the projection plane

A runout is _____.

the quality of a round in which a sharp corner has only a slight relief / a characteristic of intersecting features, determined by locating the line of intersection between the mating parts

In the absolute coordinate system, the origin location is

0,0,0

Which of the following coordinates will define a point at the screen default origin?

0,0,0

Which is the correct setting for the DIMTOLJ system variable to make tolerances middle justified in relationship to the dimension text?

1

What is the default value for the LTSCALE command?

1.0000

How many previous Zooms are available with the previous option of the ZOOM command?

10

The ARC command has how many options?

11

What is the default value for GRIPSIZE?

3

The default text rotation angle in AutoCAD (measured in a counterclockwise direction) is which of the following?

3 o'clock /

When a print shows a circle on a slanted surface in a multiview, the angle of ellipse is ____.

30° ellipse /

How many options are available in the CHPROP command?

6

To reproduce an object 7 times in a half circular pattern, use the polar option of the ARRAY command with the number of items and angle of

6 and 180 / 6 and 360 /

In the -LAYER command, which option provides a listing of the defined layer including layer name, state, color and linetype?

? (Question Mark)

A leader line is capped with this when the leader points inside the object:

A .05 in. (1.5 mm) arrowhead

When the MEASUREINIT system variable is set to zero, the drawing settings are based on the template

ACAD.DWT

The ___ command is used to make multiple copies of one or more objects in rectangular or polar patterns.

ARRAY

The ____ command is used to make multiple copies of one or more objects in rectangular or polar patterns.

ARRAY

Identify the ASME standard titled Decimal Inch Drawing Sheet Size and Format.

ASME Y14.1

Identify the ASME standard titled Metric Drawing Sheet Size and Format

ASME Y14.1M

The American Society of Mechanical Engineers (ASME) publication that recommends multiview drafting standards is:

ASME Y14.3, Multi and Sectional View Drawing

Which information is not given with the STATUS command?

Active space limits / Current Layer Name /

Phantom lines are:

All of the above

The LENGTHEN command has the following options available:

All of the above

The STRETCH command will alter the following elements if they reside inside the selection window:

All of the above

The front view of an object should:

All of the above

The front view should:

All of the above

Which part of a dimension will the DIMCLRD system variable assign color to?

All of the above / Arrowheads

A view enlargement ____.

All of the above / Is used primarily when a detail that needs to be dimensioned is too small to show the dimensions clearly / Is a view with a larger scale than that used on the regular multiviews / Is used primarily when a detail that needs to be dimensioned is too small to show the dimensions clearly AND Has a thick phantom line circle around the area to be enlarged with a detail view identification letter

When selecting an object to hatch, what selection mode controls the object selection?

Associative Hatch

The default settings of AutoCAD

Assumes that 0 degrees is to the right AND Assumes that angles increase in the counterclockwise direction

Toolbars can

Be resized, Be docked or floating, AND/OR Change their contents

The following objects may be used as a valid boundary edge when using the EXTEND command.

Both b and c

There are two types of this line one for short spaces and the other for longer spaces.

Break Line

Relieving stress factors on parts can be accomplished by the use of ____.

Break Points /

Which system variable sets the MULTILINE style?

CMLSTYLE

Which of the following is not supported by the noun/verb feature?

COPY / MOVE /

Once and object is erased from a drawing, which of the following commands could restore it to the drawing?

Cancel

Which is not a MULTILINE justification choice?

Center

Thick line made up of long and short dashes used to show portion of surface receives specified treatment

Chain Line

The SETVAR command

Changes system variables

Drafting revisions are completed in:

Chronological Order

When drawing a hexagon using the POLYGON command, the ____ option will allow you to use the distance across tC

Circumscribe

When drawing a hexagon using the POLYGON command, the ____ option will allow you to use the distance across the flats.

Circumscribe

What happens when you select the "close" option while in the LINE command?

Closes the polygon and terminates the line command

In the LAYER command, which option allows you to change the color of a named layer?

Color

Used for laying out the drawing, drawn so lightly that they are not mistaken for any other type of line.

Construction Line

Thin line used to show where the cutting-plane line has cut through material.

Cutting-Plane Line

Which system variable controls dimension user-positioned text options?

DIMTXT /DIMSTYLE /

Whenever you begin a new drawing, AutoCAD creates a new drawing called

DRAWING.DWG.

A hidden line is ____.

Dashed

A section line is similar to a visible object line, except it is ____.

Dashed

What command option allows you to key in a distance, and the direction is determined by the cursor location?

Direct distance

If a drawing extends outside the drawing limits, the ZOOM all option will

Display the entire Drawing

When a the line of sight in a multiview is perpendicular to a hole, the hole appears ____.

Elliptical / Round

A common use for and arc is one of the following

End of a slot

To repeat the previous command, you can press

Enter AND Spacebar

What command is used to remove objects from the drawing?

Erase

The ERASE command

Erases any object selected AND Erases any group of objects selected

Thin line used to establish the extent of a dimension.

Extension Line

Which function key toggles the SNAP mode on and off?

F9

A Fence must be closed.

FALSE

A drawing with a single view is always an inadequate way to describe an object.

FALSE

A first-angle projection shows only the front view, the right side view, and the top view.

FALSE

A multiview projection shows an object in a 3D picture.

FALSE

A sheet with the size designation of "A1" measures 8 1/2" by 11" and is in horizontal format.

FALSE

A view with the most contours is one of the functions of a partial view.

FALSE

An absolute rectangular coordinate is based on the last specified point.

FALSE

An enlarged view is shown directly above the portion of view from which it came.

FALSE

Fillets are slightly rounded outside curves at corners.

FALSE

First-angle projection is the principal multiview projection used in the United States.

FALSE

Hidden lines are not used in a first-angle projection.

FALSE

In a third-angle projection, the height is shown in only three views.

FALSE

In architectural and engineering units modes, the unit automatically equals one foot.

FALSE

Isometric circles appear round.

FALSE

It is easier for an individual to visualize an orthographic projection than it is to visualize a pictorial view.

FALSE

Lettering on sketches does not need to be readable.

FALSE

Lowercase letters are quite common in mechanical drafting.

FALSE

Multilines can be edited if they are exploded.

FALSE

Orthographic projection is any projection of the features of an object onto an imaginary plane called a pictorial plane.

FALSE

Rounds and fillets in multiviews always have lines projected onto the views that show the actual beginning and end of the round or fillet curves.

FALSE

Sketching a 45° line is helpful when transferring width dimensions between the front view and the top view.

FALSE

Standard line thicknesses are 0.06 mm minimum for thick lines and 0.03 mm minimum for thin lines.

FALSE

The 3 point circle option draws a circle based on two points on the circumference and the center point.

FALSE

The ERASE hot key, "ER", is a fast way to delete an object.

FALSE

The bottom view usually shows the most hidden features.

FALSE

The front view always has the longest dimensions.

FALSE

The function key used to toggle the coordinate display is the F8 key.

FALSE

The mechanical engineer's 50 scale is for scaling dimensions that require additional accuracy, because each inch has 50 divisions, making each increment .05 in. (1 ¸ 50 = .05).

FALSE

The third-angle projection symbol shows two symbols (views) of a truncated cone. The view on the right shows the cone with the larger base (longer line representing larger circle) on the left.

FALSE

There are always two dimensions common between adjacent views.

FALSE

There are six primary views that used to describe an object completely, it is often necessary to use all six views on a print.

FALSE

There is no need for proportion when sketching an object.

FALSE

To draw multiple connected line segments, you must invoke the line command multiple times.

FALSE

Views called portion views are used when symmetrical objects are shown in a limited space.

FALSE

Visible lines, also called object lines or outlines, describe the visible surface or edge of the object, and are drawn .2in. (0.6 mm) wide.

FALSE

When only two views are shown on a print, it is best to see the front view and the top view.

FALSE

When the grips system variable is set to 1, grips are turned off, while a setting of 0 turns grips on.

FALSE

When using the absolute coordinate entry method, the user must use the @ symbol.

FALSE

When using the window options, all objects within and touching the window are selected.

FALSE

Three views are always used to describe an object adequately.

False

Which option can cross itself as it is created?

Fence

In situations where the plane of projection is not parallel to the surface of the object, the resulting orthographic view is ____.

Foreshortened

Under which pull-down menu will you find Layer?

Format

The AutoCAD screen consists of the following:

Graphics window, Toolbars, AND/OR Command window

Represents an invisible edge of an object.

Hidden Line

What does the EDGEMODE system variable control?

How TRIM and EXTEND determine cutting edges

Which command displays the coordinates of a specific point in a drawing?

ID

Orthographic projection ____.

Is any projection of the features of an object onto an imaginary plane called a plane of projection AND is a projection of the features of an object which is made by lines of sight that are perpendicular to the plane of projection

To turn a series of line segments into a polyline, one uses the PEDIT option of

Join

To turn a series of line segments into a polyline, one uses which option of the PEDIT command?

Join

To turn a series of the line segments into a polyline, one uses which option of the PEDIT command?

Join

Used to connect a specific note to a feature.

Leader Line

In the LAYER command, which option allows a named layer to be visible, but does not allow entities on that layer to be edited with modify commands?

Lock

In the LAYER command, which option make the layer visible and enables regeneration of that layer?

Lock / Unlock /

Which of the following sheet sizes is 22"x17"?

Mechanical C

Which of the following sheet sizes is 34"x22"?

Mechanical D

The ERASE command can be found from panel named?

Modify

Which object snap mode snaps to the nearest point on an arc, circle, ellipse, elliptical arc, line, mline, point, polyline, spline, or xline

Nearest

Which object snap mode snaps to the nearest point on an arc, circle, ellipse, elliptical arc, line, mline, point, polyline, spline, or xline?

Nearest

What is the difference between cutting plane lines and viewing plane lines?

None of the above

What is the standardized lettering format that was established in 1935 by ANSI?

None of the above

In regards to a spline, what does "nurbs" mean?

None of the above /

If a 30° slanted surface has a perpendicular hole, then the angle of ellipse in the adjacent view is ____.

None of the above / 60° /

Once an object is erased from a drawing, which of the following commands could restore it to the drawing?

OOPS

Which command constrains cursor movements to the horizontal or vertical directions ( relative to the UCS)?

ORTHO

Which command constrains cursor movements to the horizontal or vertical directions (relative to the UCS)?

ORTHO

In the LAYER command, which option makes the named layer invisible?

Off

In the Drafting Settings dialog box, which of the following option(s) is in the Snap section?

Off, On, X-Spacing, Y-Spacing / Off, On, Snap Angle, X-Spacing /

Used to identify alternate positions of moving parts.

Phantom Line

These lines are used to identify alternate positions of moving parts.

Phantom Lines

The Object option of the AREA command is used to select

Polylines

In order to perform several commands on the same object, the ____ option is used to prevent having to select the same object again.

Previous

In order to perform several commands on the same object. the ___ option is used to prevent having to select the same object again.

Previous

Which is not an option of the UNDO command?

Previous

If you just used the U command, what command would restore the drawing to the state before the U command?

REDO

The ___ command only refreshes the screen display

REDRAW

The ____ command only refreshes the screen display.

REGEN /REFRESH /

When the AUNITS system variable is set to 3, angles are measured in

Radians

What kinds of runouts can exist on a multiview print?

Round and Eliptical /

When a sharp exterior corner has only a slight relief, it is called a ____.

Runout / Round / Fillet / None of the above / Break Corner

Which command allows you to change the size of an object, where the X and Y scale factors change equally?

SCALE

What command restricts cursor movements to specified intervals?

SNAP

The invisible grid which the crosshairs lock onto is called

SNAP GRID

Thick lines used to show where a section view is taken.

Section Line

These lines are used in the view of a section to show where the object has been cut.

Section Lines

Which is not an option of the AREA command?

Select

Which command allows you to select multiple objects by specifying criteria?

Select /Window /

The "S,E,R" options of the ARC command is short for

Start, End, Radius

There are two acceptable types of this line. One drawn with dashes, the other drawn with dots.

Stitch Line

"Continuation from line" is one of the options of the ARC command.

TRUE

A "bolt circle" is a pattern of holes arranged in a circle.

TRUE

A check box acts as a toggle.

TRUE

A cylinder is an object that can be shown with one view.

TRUE

A floating toolbar can lie anywhere on the screen and can be resized.

TRUE

A grid frame of reference is helpful when sketching an irregular object.

TRUE

A hidden line represents an invisible edge on an object. Hidden lines are thin lines drawn .01 in. (0.3 mm) thick.

TRUE

A hole through a slanted surface in the front view appears as an ellipse in the side view from which the slanted surface is projected.

TRUE

A multiview drawing can represents the shape of an object using one view.

TRUE

A multiview drawing represents the shape of an object using two or more views, but using one view is an option for some objects.

TRUE

A pictorial view shows three sides of an object.

TRUE

A scale establishes a proportion used in determining the dimensional relationship of an actual object to the representation of the same object on a drawing.

TRUE

A scale is an instrument with a system of ordered marks at fixed intervals used as a reference standard in measurement.

TRUE

A solid filled polygon is generated with straight sides.

TRUE

A spline-fit Pline can be turned into a spline.

TRUE

Absolute rectangular coordinates are located in relation to the origin.

TRUE

All lines of the same type have uniform thickness throughout the drawing.

TRUE

All surfaces should be shown true size on a multiview print when possible

TRUE

An object can be so complex as to warrant using all available views in order to describe it adequately.

TRUE

AutoCAD allows you to use certain commands transparently.

TRUE

AutoCAD can open multiple drawings in a single session.

TRUE

Certain casting methods require that inside corners of parts have fillets.

TRUE

Cylindrical objects can be represented with only a front view and a top view.

TRUE

Depth dimensions are the same between top views and side views.

TRUE

Extension lines are thin lines used to establish the extent of a dimension and begin with a .06 in. (1.5 mm) space from the object and extend to about .125 in. (3 mm) beyond the last dimension.

TRUE

Extension lines can be used to show the extension of a surface to a theoretical intersection.

TRUE

In a third-angle projection, the quadrant of visualization from which the object derives its views is the lower right quadrant, also known as the third quadrant.

TRUE

In an orthographic view, some planes can be foreshortened.

TRUE

In general, a REDRAW is quicker than a REGEN.

TRUE

In order to draw two RAY's with different starting points, you must use the RAY command twice.

TRUE

Isometric lines are parallel to the isometric axes lines

TRUE

It is important to have contours represented correctly for accurate print reading.

TRUE

It is important to sketch features of an object lightly by estimating distances within the rectangular box, which has already been drawn.

TRUE

Keeping views aligned in a multiview sketch makes the sketching and understanding easier.

TRUE

Like a Block, a Group is one object until it is exploded.

TRUE

Major and minor diameters represent the width and length of an ellipse.

TRUE

Military (MIL) standards recommend three line thicknesses: thick (cutting and viewing-plane, short break, and object), medium (hidden and phantom), and thin (center, dimension, extension, leader, long break, and section).

TRUE

Multiline vertices can be deleted.

TRUE

Multiview projection establishes views of an object projected upon two or more planes of projection by using orthographic projection techniques, and the result of multiview projection is a multiview drawing

TRUE

Multiview projection establishes views of an object projected upon two or more planes of projection by using orthographic projection techniques, and the result of multiview projection is a multiview drawing.

TRUE

On ten of the triangular architect's scales, each inch represents a specific increment of feet. Each of the feet is subdivided into multiples of 12 parts to represent inches and fractions of an inch.

TRUE

Orthographic projection is any projection of the features of an object onto an imaginary plane called a plane of projection, and the projection of the features of the object is made by lines of sight that are perpendicular to the plane of projection.

TRUE

Partial views can be used when symmetrical objects are drawn in limited space or when there is a desire to simplify complex views.

TRUE

Points can be added to a spline after it is drawn.

TRUE

Regardless of the current unit setting, you can always enter units in decimal format.

TRUE

Scroll bars located on the side and bottom of the view screen work similar to the PAN command.

TRUE

The @ symbol must be used for the input of relative polar coordinates.

TRUE

The ASME standard for lines and lettering is, Line Conventions and Lettering, ASME Y14.2.

TRUE

The American Society of Mechanical Engineers (ASME) publication ASME Y14.3, Multi and Sectional View Drawings recommends standards for multiview drawings.

TRUE

The American Society of Mechanical Engineers (ASME) recommends two-line thickness, which are thick and thin lines.

TRUE

The Box option resembles both the Window and Window Crossing in selection methods.

TRUE

The DONUT command lets you draw solid-filled circles and rings by specifying outer and inner diameters of the filled area.

TRUE

The Implied Window selection option default is set to "on".

TRUE

The NEW command allows you to begin a new drawing.

TRUE

The OPEN command allows you to open an existing drawing.

TRUE

The SKETCH command creates a series of freehand line segments.

TRUE

The SPLINE command creates an irregular curve.

TRUE

The TTR option of the CIRCLE command draws a circle tangent to two objects with a specified radius.

TRUE

The VPORTS command creates tiled viewports.

TRUE

The approximate inch conversiion for standard line thickness is .02 in. (0.6 mm) for thick lines and .01 in. (.03 mm) for thin lines. This establishes a two-to-one ratio between thick and thin lines.

TRUE

The arrowhead is omitted when a leader line points to a dimension line. This is done when there is not enough space for text to be inserted at the dimension line, and the text is connected to the leader.

TRUE

The center option of the Polygon command first prompts you for a center point of the polygon to be drawn.

TRUE

The centerline method for creating a circle is when you sketch very light horizontal, vertical, and 45° lines that meet at the center of the proposed circle.

TRUE

The centerline method for sketching a circle is different from the box method.

TRUE

The civil engineer's scales are calibrated in multiples of ten.

TRUE

The common form of multiview alignment is one in which the front view is the most important view to select first.

TRUE

The default limits, if MEASUREINIT is set to zero, are set to 0,0 for the lower left, and 12,9 for the upper right corner.

TRUE

The drawing pen can be easily raised and lowered while in the SKETCH command.

TRUE

The drawing title block usually indicates the scale at which most views are drawn, or the predominant scale of a drawing.

TRUE

The front view is usually the most important view.

TRUE

The mechanical engineer's scale typically has full-scale divisions that are divided into 1/16, 10, and 50.

TRUE

The result of a multiview projection is a multiview drawing.

TRUE

The size that the POINT appears on the screen depends on the value to which the PDSIZE system variable is set.

TRUE

The status bar at the bottom of the screen displays the cursor's coordinates and important information on the status of various modes.

TRUE

The title bar displays the current drawing name for the AutoCAD application window.

TRUE

The two standard projection methods for creating multiviews are first- and third-angle projection.

TRUE

The versatile PLINE command draws lines and arcs of different widths and tapered lines.

TRUE

Vertical uppercase letters are the industry standard.

TRUE

When a sub-dialog box appears, you must respond to the options in the sub-dialog box before the underlying dialog box can continue.

TRUE

When an object has a uniform shape and thickness, more than one view is normally unnecessary.

TRUE

When an object has shape and a uniform thickness, more than one view is unnecessary, especially if the view is identified by dimensional shape.

TRUE

When prompted to select an object, typing L will select the last object created.

TRUE

When you draw the POINT, it will appear on the display as a blip if the BLIPMODE system variable is set to ON.

TRUE

When you use a template to create a new drawing, AutoCAD copies all the information from the template drawing to the new drawing.

TRUE

XLINE and RAY commands allow you to draw lines that extend infinitely in one or both directions.

TRUE

The following are AutoCAD tools available, except

TSNAP

Hidden lines ____.

Take precedence over centerline AND should be kept to a minimum in front views

To create a rectangular ARRAY of objects, you must specify

The Number of Rows, the number of Columns, and the unit cell size

If you see the depth and height dimensions of an object in third-angle projection, which views of the multiview print do you see?

The Right Side View

The depth of an object shown in a multiview print is common between ____.

The Top View and the Right Side View

Points are located by relative rectangular coordinates in relation to

The last specified point or position

Points are located by relative rectangular coordinates in relation to?

The last specified point or position

Relative polar coordinates are based on a distance from

The last specified position at a given angle

Relative polar coordinates are based on a distance from ?

The last specified position at a given angle

The TRACE command acts just like the LINE command, except

The line width is never set *WRONG

ASME gives several recommendations for lettering. Which one among the following list is not part of those considerations?

The minimum lettering size is .125 mm on engineering drawings

By default, the Start Point option of TEXT indicates which of the following?

The upper left corner of the text / The center of the text /

Text can be highlighted by doing which of the following?

Triple-Clicking to select a paragraph /All of the above /

How many line thicknesses does ASME recommend?

Two

Slightly contoured objects can be shown in multiview as having rounded features by ____ to accent the rounded features.

Using phantom lines AND using shading / Using light continuous lines / Shading /

A ____ can be used when a view has features that cannot be dimensioned clearly.

View Enlargement

If a centerline, a hidden line, and a visible line all occur at the same space on a multiview print, which line takes precedence?

Visible Line

Which option can create a non-rectangular window that cannot cross itself?

WPolygon

Which of the following features produce runouts?

When a cylindrical shape has a point of tangency with a rectangular shape / When a pipe and an elbow connect /

The view on the plane of projection of an object shows which dimensions?

Width, Depth, Height /

Which PEDIT option and its description is NOT correct?

X: Returns to the command prompt /Width: Allows selection of new width for all segments of polylines /

A(n) ___ is used to terminate a dimension line.

arrowhead

To reverse the effect of the last 11 commands, you could

both a and b

DBLIST

both a and b /displays information about entities in the current drawing

The MOVE command allows you to

both a and c

Which option of the ZOOM command will display the entire drawing?

both a and c

A polyline

can have width / is one object /

By default, what direction does a positive number indicate when specifying angles in degrees?

counter-clockwise

A hidden line is ___

dashed

When the grips show as unfilled squares but the object is not highlighted, grips are

hot /warm /

The DISTANCE command

measures the distance between two points.

When the surface of an object is ____ the plane of projection, the surface appears in its true size and shape on the plane of projection.

parallel to

Multiviews are views of and object in which the line of sight is ___the surfaces of the object.

perpendicular to

These lines are used to identify alternate positions of moving parts

phantom lines

Whit is the term for when the arc touches the line at only one point and does not cross over the line?

tangent

The QTEXT utility command reduces regeneration time when

the drawing contains a great amount of text / all of the above

If a center line, a hidden line, and a visible line all occur at the same space on a multiview print, which line takes precedence?

visible line