CCNA 2 Practice Final (as of May 2021)

¡Supera tus tareas y exámenes ahora con Quizwiz!

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the administrative distance?

1

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the destination network?

10.3.0.0

What address and prefix length is used when configuring an IPv6 default static route?

::/0

Match the dynamic routing protocol component to the characteristic. (Not all options are used.) A finite list of steps used to determine the best path

Algorithm

On which port should Dynamic ARP Inspection (DAI) be configured on a switch?

An uplink port to another switch

Which term describes the role of a Cisco switch in the 802.1X port-based access control?

Authenticator

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the route source protocol?

D

Refer to the exhibit. SW1(config)# ip arp inspection validate ip SW1(config)# ip arp inspection validate src-mac SW1(config)# ip arp inspection validate dst-mac SW1(config)# end SW1(config)# A network administrator is configuring DAI on switch SW1. What is the result of entering the exhibited commands?

DAI will validate only the destination MAC addresses

Match the purpose with its DHCP message type. (Not all options are used.) A message that is used to acknowledge that the lease is successful

DHCPACK

Match the purpose with its DHCP message type. (Not all options are used.) A message that is used to locate any available DHCP server on a network

DHCPDISCOVER

Match the purpose with its DHCP message type. (Not all options are used.) A message that is used to suggest a lease to a client

DHCPOFFER

Match the purpose with its DHCP message type. (Not all options are used.) A message that is used to identify the explicit server and lease offer to accept

DHCPREQUEST

Match the dynamic routing protocol component to the characteristic. (Not all options are used.) Tables or databased that are stored in RAM

Data structures

What is the best way to prevent a VLAN hopping attack?

Disable trunk negotiation for trunk ports and statically set nontrunk ports as access ports

Which Cisco solution helps prevent ARP spoofing and ARP poisoning attacks?

Dynamic ARP Inspection

Match the DTP mode with its function. (Not all options are used.) What passively waits for the neighbor to initiate trunking?

Dynamic auto

Match the DTP mode with its function. (Not all options are used.) What actively attempts to convert the link to a trunk?

Dynamic desirable

A network engineer is configuring a LAN with a redundant first hop to make better use of the available network resources. Which protocol should the engineer implement?

GLBP

Match the FHRP protocols to the appropriate description. (Not all options are used.) A Cisco proprietary FHRP that provides load sharing in addition to redundancy

GLBP

Match the FHRP protocols to the appropriate description. (Not all options are used.) A Cisco Proprietary FHRP that provides redundancy through use of an active device and standby deice

HSRP

Which statement describes the behavior of a switch when the MAC address table is full?

It treats frames as unknown unicast and floods all incoming frames to all ports within the local VLAN

Match the spanning-tree feature with the protocol type. (Not all options are used.) IEEE standard that reduces the number of STP instances

MSTP

Match the DTP mode with its function. (Not all options are used.) What require manual configuration of trunking or nontrunking?

Nonegotiate

Match the spanning-tree feature with the protocol type. (Not all options are used.) Cisco implementation of IEEE 802.1D

PVST+

What is an advantage of PVST+?

PVST+ optimizes performance on the network through load sharing

Refer to the exhibit. How is a frame sent from PCA forwarded to PCC if the MAC address table on switch SW1 is empty?

SW1 floods the frame on all ports on SW1, excluding the port through which the frame entered the switch.

A small publishing company has a network design such that when a broadcast is sent on the LAN, 200 devices receive the transmitted broadcast. How can the network administrator reduce the number of devices that receive broadcast traffic?

Segment the LAN into smaller LANs and route between them

A network administrator is using the router-on-a-stick method to configure inter-VLAN routing. Switch port Gi1/1 is used to connect to the router. Which command should be entered to prepare this port for the task?

Switch(config)# interface gigabitethernet 1/1 Switch(config-if)# switchport mode trunk

An administrator has configured a DHCPv4 relay router and issued these commands: Router(config)# interface g0/0 Router(config-if)# ip address 10.0.1.1 255.255.255.0 Router(config-if)# no shutdown Router(config-if)# exit Router(config)# ip dhcp pool RELAY Router(dhcp-config)# end The clients are not receiving IP parameters from the DHCPv4 server. What is a possible cause

The "ip helper-address" command is missing

Refer to the exhibit. Based on the command output shown, what is the status of the EtherChannel?

The EtherChannel is in use and functional as indicated by the SU and P flags in the command output

Refer to the exhibit. R1# show running-config <output omitted> ipv6 unicast-routing ! ipv6 dhcp pool Lan1 prefix-delegation 2001:DB8:5::/48 0030001000E84244E70 dns-server 2001:DB8:5::8 domain-name cisco.com ! interface FastEthernet0/0 no ip address ipv6 address 2001:DB8:5::100/48 ipv6 dhcp server LAN1 The users on the LAN network of R1 cannot receive an IPv6 address from the configured stateful DHCPv6 server. What is missing from the stateful DHCPv6 configuration on router R1?

The FA0/0 interface is missing the command that informs the clients to use stateful DHCPv6.

Refer to the exhibit. S1(config)# interface fa0/1 S1(config-if)# switchport port-security Command rejected: FastEthernet0/1 is a dynamic port. S1(config-if)# The administrator wants to enable port security on an interface on switch S1, but the command was rejected. Which conclusion can be drawn?​

The interface must be initially configured with the "switchport mode access" command

A network administrator is configuring a WLC to provide WLAN access to users in an office building. When testing the newly created WLAN, the administrator does not see the SSID from a wireless device. What is a possible cause?

The new WLAN needs to be enabled

Refer to the exhibit. R1# show ipv6 route <output omitted> S :: /0 [1/0] via Serial0/0/0, directly connected C 2001:DB8:CAFE:1::/64 [0/0] via GigabitEthernet0/1. directly connected L 2001:DB8:CAFE:1::1/128 [0/0] via GigabitEthernet0/1, receive C 2001:DB8:CAFE:2::/64 [0/0] via GigabitEthernet0/0, directly connected L 2001:DB8:CAFE:2::1/128 [0/0] via GigabitEthernet0/1, receive C 2001:DB8:CAFE:3::/64 [0/0] via Serial0/0/0, directly connected L 2001:DB8:CAFE:3::1/128 [0/0] via Serial0/0/0, receive S 2001:DB8:CAFE:4::1/128 [1/0] via Serial0/0/0, directly connected L FF00::/8 [0/0] via Null0, receive How was the host route 2001:DB8:CAFE:4::1/128 installed in the routing table?

The route was manually entered by an administrator

Refer to the exhibit. Fa0/1 (Switch) > Fa0/2, Fa0/3, Fa0/4 (PCs) <output omitted> interface FastEthernet 0/1 switchport trunk allowed vlan 10.20.30 switchport mode access switchport nonnegotiate ! interface FastEthernet 0/2 switchport access vlan 10 switchport mode access switchport nonegotiate ! interface FastEthernet 0/3 switchport access vlan 20 switchport mode access switchport nonegotiate ! interface FastEthernet 0/4 switchport access vlan 30 switchport mode access switchport nonegotiate Inter-VLAN communication between VLAN 10, VLAN 20, and VLAN 30 is not successful. What is the problem?

The switch interface FastEthernet0/1 is configured as an access interface and should be configured as a trunk interface.

Match the DTP mode with its function. (Not all options are used.) What is a permanent trunking mode?

Trunk

Which type of traffic is designed for a native VLAN?

Untagged

In what situation would a Layer 2 switch have an IP address configured?

When the Layer 2 switch needs to be remotely managed

What is the reason for disabling SSID broadcasting and changing the default SSID on a wireless access point?

Wireless clients must have the SSID manually configured to connect to the wireless network

Consider the following command: ip route 192.168.10.0 255.255.255.0 10.10.10.2 5 What does the 5 at the end of the command signify?

administrative distance

What are two switch characteristics that could help alleviate network congestion? (Choose two.)

fast internal switching large frame buffers

Which command will start the process to bundle two physical interfaces to create an EtherChannel group via LACP?

interface range GigabitEthernet 0/4 - 5

Which command would create a valid IPv6 default route?

ipv6 route ::/0 2001:db8:acad:2::a

Refer to the exhibit. ____________________________________________ DLS1# show interfaces trunk Port Mode Encapsulation Status Native vlan Fa0/1 on 802.1q trunking 99 Port Vlans allowed on trunk Fa0/1 1, 10, 20, 30, 99, 1001-1005 Port Vlans allowed and active in management domain Fa0/1 1, 10, 20, 30, 99 Port Vlans in spanning tree forwarding state, not pruned Fa0/1 10, 20, 30, 99 DLS1# *Mar 1 00:05:53:54: %CDP-4 NATIVE_VLAN_MISMATCH: Native VLAN mismatch discovered on FastEthernet0/1 (99), with DLS2 FastEthernet0/1 (66). ______________________________________________ DLS1 is connected to another switch, DLS2, via a trunk link. A host that is connected to DLS1 is not able to communicate to a host that is connected to DLS2, even though they are both in VLAN 99. Which command should be added to Fa0/1 on DLS1 to correct the problem?

switchport trunk native vlan 66

What are the two methods that a wireless NIC can use to discover an AP? (Choose two.)

transmitting a probe request receiving a broadcast beacon frame

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the route timestamp?

00:22:15

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the next hop?

172.16.2.2

Refer to the exhibit. Match the description with the routing table entries. (Not all options are used.) 172.16.0.0/24 is subnetted, 3 subnets C 172.16.0.0/24 is directly connected, Serial0/1/0 D 172.16.1.0 {90/21024000} VIA 172.16.0.1, 00:22:15, Serial 10/1/0 C 172.16.2.0 is directly connected, Serial10/1/1 10.0.0.0/24 is subnetted, 1 subnets S 10.2.0.0 [1/0] via 172.16.2.2 C 10.3.0.0 is directly connected, FastEthernet0/0 What is the metric?

21024000

Which problem is evident if the show ip interface command shows that the interface is down and the line protocol is down?

A cable has not been attached to the port

Refer to the exhibit. Router R1 has an OSPF neighbor relationship with the ISP router over the 192.168.0.32 network. The 192.168.0.36 network link should serve as a backup when the OSPF link goes down. The floating static route command ip route 0.0.0.0 0.0.0.0 S0/0/1 100 was issued on R1 and now traffic is using the backup link even when the OSPF link is up and functioning. Which change should be made to the static route command so that traffic will only use the OSPF link when it is up?

Change the administrative distance to 120

A junior technician was adding a route to a LAN router. A traceroute to a device on the new network revealed a wrong path and unreachable status. What should be done or checked?

Check the configuration of the exit interface on the new static route.

A network administrator is implementing DHCPv6 for the company. The administrator configures a router to send RA messages with M flag as 1 by using the interface command ipv6 nd managed-config-flag . What effect will this configuration have on the operation of the clients?

Clients must use all configuration information that is provided by a DHCPv6 server.

After sticky learning of MAC addresses is enabled, what action is needed to prevent dynamically learned MAC addresses from being lost in the event that an associated interface goes down?

Copy the running configuration to the startup configuration

What are two characteristics of Cisco Express Forwarding (CEF)? (Choose two.)

Packets are forwarded based on information in the FIB and the adjacency table

A network administrator of a college is configuring WLAN security with WPA2 Enterprise authentication. Which server is required when deploying this type of authentication?

RADIUS

Match the spanning-tree feature with the protocol type. (Not all options are used.) Fast converging enhancement of IEEE 802.1D

RSTP

Match the spanning-tree feature with the protocol type. (Not all options are used.) Proprietary per VLAN implantation of IEEE 802.1w

Rapid PVST+

Refer to the exhibit. When a packet arrives on interface Serial0/0/0 on R1, with a destination IP address of PC1, which two events occur? (Choose two)

Router R1 will forward the packet out Gig0/1 Router R1 will de-encapsulate the packet and encapsulate it in an Ethernet frame

Match the dynamic routing protocol component to the characteristic. (Not all options are used.) Exchanges routing information and maintains accurate information about networks

Routing protocol messages

Match the FHRP protocols to the appropriate description. (Not all options are used.) An open standard FHRP that provides redundancy through use of a virtual routers master and one or more backups

VRRP

Refer to the exhibit. The routing table for R2 is as follows: Gateway of last resort is not set 10.0.0.0/30 is subnetted, 2 subnetsC 10.0.0.0 is directly connected, Serial0/0/0C 10.0.0.4 is directly connected, Serial0/0/1192.168.10.0/26 is subnetted, 3 subnetsS 192.168.10.0 is directly connected, Serial0/0/0C 192.168.10.64 is directly connected, FastEthernet0/0S 192.168.10.128 [1/0] via 10.0.0.6 What will router R2 do with a packet destined for 192.168.10.129?

Send the packet out interface Serial0/0/1

Refer to the exhibit: Gateway of last resort is not set. 172.18.109.0/26 is variously subnetted, 7 subnets, 3 masks O 172.18.109.0/26 [110/10] via 172.18.32.1, 00:00:24, Serial0/0/0 O 172.18.109.64/26 [110/20] via 172.18.32.6, 00:00:56, Serial 0/0/1 O 172.18.109.128/26 [110/10] via 172.18.32.1, 00:00:24, Serial 0/0/0 C 172.18.109.192/27 is directly connected, GigabitEthernet0/0 L 172.18.109.193/27 is directly connected, GigabitEthernet0/0 C 172.18.109.224/27 is directly connected, GigabitEthernet0/1 L 172.18.109.225/27 is directly connected, GigabitEthernet0/1172.18.32.0/24 is variably subnetted, 4 subnets, 2 masks C 172.18.32.0/30 is directly connected, Serial0/0/0 L 172.18.32.2/32 is directly connected, Serial0/0/0 C 172.18.32.4/30 is directly connected, Serial0/0/1 L 172.18.32.5/32 is directly connected, Serial0/0/1 S 172.18.33.0/26 [1/0] via 172.18.32.1, 00:00:24, Serial0/0/0R1# Which interface will be the exit interface to forward a data packet that has the destination IP address 172.18.109.152?

Serial0/0/0

A small coffee shop is offering free Wi-Fi to customers. The network includes a wireless router and a DSL modem that is connected to the local phone company. What method is typically used to configure the connection to the phone company?

Set the WAN connection in the wireless router as a DHCP client

Refer to the exhibit. PC-A and PC-B are both in VLAN 60. Port Mode Encapsulation Status Native vlan Fa0/18 on 802.1q trunking 99 Port Vlans allowed on trunk Fa0/18 1, 10, 20, 30, 40, 50, 70, 80, 90, 100, 1001-1005 Port Vlans allowed and active in management domain Fa0/18 1, 10, 20, 30, 40, 50, 70, 80, 90, 100 Port Vlans in spanning tree forwarding state, not pruned Fa0/18 1, 10, 20, 30, 40, 50, 70, 80, 90, 100 PC-A is unable to communicate with PC-B. What is the problem?

The VLAN that is used by PC-A is not in the list of allowed VLANs on the trunk.

What is a result of connecting two or more switches together?

The size of the broadcast domain in increased

What is a potential issue when using the WLC to upgrade and deploy the latest firmware image to all APs?

Users will not be able to use the WLAN

Which combination of WLAN authentication and encryption is recommended as a best practice for home users?

WPA2 and AES

Which three components are combined to form a bridge ID?

extended system ID bridge priority MAC address

What type of VLAN is configured specifically for network traffic such as SSH, Telnet, HTTPS, HTTP, and SNMP?

management VLAN

Refer to the exhibit. A network administrator is troubleshooting a problem with EtherChannel. What command was used to produce the exhibited output?

show interfaces fastethernet 0/11 etherchannel


Conjuntos de estudio relacionados

Spanish Influence at Home and Abroad

View Set

Asexual and Sexual Reproduction Flash Cards

View Set

Lifespan Developmental Psych Chapter 16

View Set

Chapter 6.2 U.S. History Vocabulary

View Set

SAUNDERS HESI STUDY for PHARM - Endocrine Meds

View Set

GACE: Major British Authors & Summary of Works

View Set

AP US History Chapters 26, 27, and 28

View Set

Final Exam Review US HISTORY Lyn Bordenet S2

View Set

Xcel solutions - Premiums and proceeds

View Set